ROBORE X5F

Contents

ROBORE X5F Foldable Treadmill User Manual

Model: X5F

1. Important Precautions

IMPORTANT!

Your satisfaction is very important to us. If you encounter any issues such as shipping damage, missing parts, error code, or defects, please contact us. We will ensure to provide a satisfactory solution.

PLEASE DO NOT RETURN UNTIL YOU HAVE CONTACTED US:

E-Mail: service_sports@163.com

Please provide your Order ID and Product problem (attached pictures or videos if necessary).

2. Main Technical Features

  • Motor: 3.0HP (Quiet operation, <45db low noise)
  • Weight Capacity: 330lbs / 150kg
  • Max. Speed: 10km/h (6.3MPH)
  • Incline Levels: 2%, 10%, 16% (Adjustable slope)
  • Running Belt: Non-slip diamond pattern, multi-layer shock-absorbing system (92cm x 39cm)
  • Exercise Modes: 4-in-1 (Working, Walking, Jogging, Running)
  • Display: LED screen to track Speed, Time, Distance, Calories
  • Control: Remote Control
  • Portability: Foldable design with smooth mobile wheels for easy storage
  • Versatility: Under-desk usable for office settings, adjustable handles
  • Power Supply: AC 220-240V
3.0HP Powerful & Quiet Motor diagram with specifications

Figure 1: Motor specifications and noise level.

Treadmill with 16% incline and calorie burning graph

Figure 2: 16% Incline Treadmill with calorie burning graph.

Treadmill showing 4-in-1 exercise modes and speed ranges

Figure 3: 4-in-1 Treadmill modes and speed ranges.

3. Assembly Instructions

The ROBORE X5F Treadmill requires minimal assembly. Please follow the steps below carefully. Refer to the assembly video for visual guidance.

Video 1: ROBORE X5F Treadmill Assembly Guide.

3.1. Package Contents

No. Item Quantity
1Remote Control1
2User Manual1
3Boost1
4Phone holder1
5Upper case1
6Armrest watch holder1
7Running deck1
8Washer M82
9Spring washer M82
10Steel ball latch M8*392
11Hexagon socket head cap screw M8*202
12Cross-recessed flat head self-tapping screw ST4*123
13Latex hole plug2
145#Hex key1
156#Hex key1
16Knob M8*202
17Knob M8*351
1813-14-15 multi-functional screwdriver1

3.2. Step-by-Step Assembly

  1. STEP1: Check if all parts are complete. Refer to the package contents list above.

  2. STEP2: Install the armrest watch holder. Align the tube holes of armrest holder (6) with running deck (7) sleeves. Use screws (11) with washers (8) and spring washers (9), tighten clockwise with hex key (15) to secure. Then fit knob (16) into the front hole as shown in Figure 4. Note: This knob is only for positioning to prevent shaking; it's normal if it can't be fully tightened.

    Diagram showing assembly of armrest watch holder

    Figure 4: Armrest watch holder assembly.

  3. STEP3: Install the side armrests, upper case, and phone holder. Align the side armrest holes with those on the armrest tube, insert steel ball latch (10). Align upper case (5) and phone holder (4) with the lower case holes on the armrest tube. Use 2 screws (12) and multi-function screwdriver (18) to tighten clockwise at marked positions for securing. Then insert phone holder into the case's corresponding position as shown in Figure 5.

    Diagram showing assembly of side armrests, upper case, and phone holder

    Figure 5: Side armrests, upper case, and phone holder assembly.

  4. STEP4: Install the hole plugs and adjust the foot pads. Take silicone hole plugs (13) and install them into the marked holes on the armrest tubes. Adjust the folding foot pads on running deck (7) to the unfolded position. Refer to Figure 6.

    Diagram showing installation of hole plugs and adjustment of foot pads

    Figure 6: Hole plug installation and foot pad adjustment.

  5. STEP5: Installation completed. Your treadmill should now be fully assembled and ready for use.

  6. STEP6: Storage state. To store the treadmill, pull out the side armrest latch, loosen armrest tube knob (16) counterclockwise, fold the armrest watch holder down to the diagram position, align its middle hole with the running deck sleeve, and secure with knob (17) (one side only). Refer to Figure 7.

    Diagram showing how to fold the treadmill for storage

    Figure 7: Folding the treadmill for storage.

4. Operating Instructions

  1. Step 1: Insert 2 AAA batteries (not included) into the remote controller.

  2. Step 2: Turn on the power switch of the treadmill.

  3. Step 3: In standby mode, press the 'M' key on the remote control to enter three countdown modes: Time, Distance, and Calorie. During mode selection, the indicator light for the current mode will always be on.

  4. Step 4: Select a mode and adjust countdown value. Use the '+' and '-' keys to increase or decrease the value of the countdown function. After setting, press 'ON/OFF' to run.

  5. Step 5: To quit the countdown function, press 'ON/OFF' again to stop.

LED Screen and Remote Control for treadmill operation

Figure 8: Remote control and LED display for operation.

5. Incline Adjustment

This machine is equipped with two levels of incline adjustment. Please adjust the angle according to your actual needs.

  • Ensure that the support feet are properly adjusted to avoid unnecessary injuries.
  • The height-increasing foot pads should only be used after the support feet have been fully extended. If the rear cover touches the ground, please adjust the height of the rear foot pads.

Rotate to adjust the height from the ground to prevent the rear guard from scraping against the floor.

Diagram showing incline adjustment mechanism

Figure 9: Incline adjustment mechanism.

6. Running Belt Corrections

  1. Check first if the Running Belt is offsetting to the left or right with a rattling noise.
  2. If the above problem occurs, please adjust the running belt to the correct position.
Diagram showing how to adjust running belt if it shifts left or right

Figure 10: Running belt adjustment for left/right shift.

If the running belt slips, use a 5mm wrench to turn both side bolts 1/4 clockwise. Repeat this procedure until the belt is properly tightened.

Caution:

  • Heavy pedaling may cause shutdown (it's an overload protection, not machine failure).
  • Current and voltage overload may cause shutdown.
  • Each person's running habits (how hard the left or right foot tread) may cause the running belt to shift slightly.

7. Maintenance

7.1. Lubrication

LUBRICATION: Correct lubrication of the treadmill with silicon oil or Teflon is very important. (ONLY FOR NORMAL BELT, IF NEEDED)

This lubrication must be performed regularly depending on its use, even before the first use.

Please lift the belt, you can add the oil under the belt. After starting the machine, please change to the highest speed; the oil will be spread from the middle between the running belt and board. You can refer to Figure 11.

Diagram showing how to lubricate the treadmill belt

Figure 11: Treadmill belt lubrication process.

7.2. Lubrication Schedule

Usage Frequency Maintenance Frequency
<3 Hours/Week2 Months
4-7 Hours/Week1 Month
>8 Hours/Week2 Weeks

The treadmill was pre-oiled for instant use, and the oil provided is 30ml. Under normal circumstances, it can be used for about one year. If your usage time is around 4-7 hours per week, the approximate amount of oil used each time is 2.5ml.

8. Troubleshooting

Error Code Error Judgment Solution
E1 Connection Error
  • The interface of the upper and lower control main connections are loose.
  • The main connection line of the upper and lower control is damaged.
  • The monitor is damaged.
  • The controller is damaged.
  • Reinforce the motor cable.
  • Replace the main connecting cable of the upper and lower control.
  • Replace the monitor.
  • Replace the controller.
E2 Motor Damaged
  • The motor wire is not connected or loose.
  • Carbon brush cover for motor is damaged.
  • The motor is damaged.
  • Reinforce the motor cable.
  • Replace the carbon brush cover for motor.
  • Replace the motor.
E5 Over-current Protection
  • Excessive load.
  • The motor or roller is stuck with foreign objects.
  • The roller is not lubricated enough, and the resistance increases.
  • The motor is damaged and the resistance increases.
  • Reduce the load and try not to exceed the rated load.
  • Remove the stuck object.
  • Add lubricant.
  • Replace the motor.
E6 Motor Over-voltage Protection
  • The user's power grid or voltage is unstable, and the peak voltage is too high.
  • The wheel diameter value was set incorrectly.
  • Controller damaged.
  • Add an external filter regulator.
  • Re-set the wheel diameter value so as not to exceed the rated.
  • Replace the controller.

9. User Tips

  • Regular use of the treadmill is encouraged for optimal fitness results.
  • The treadmill offers a good speed range, allowing for varied workout intensities.
  • Ensure the running belt is properly aligned and lubricated according to the maintenance schedule for smooth operation and longevity.

10. Warranty & Support

10.1. 5 Year Warranty

The ROBORE X5F Treadmill provides a 5-year warranty.

Warranty Description:

  • 5 Year Frame
  • 1 Year Parts

10.2. Customer Support

Contact CursorCare for 7/24 response and 100% satisfaction guarantee.

  • 7*24 online California-based customer service team to solve after-sales problems without obstacles.
  • Return Policy: 30-Day Hassle-Free Return and Exchange.
  • Customer Service: California-based Service Team providing personalized solutions to ensure 100% customer satisfaction.
  • Exclusive Maintenance Service: We honor our commitment to quality and durability by offering free maintenance tools for orders within 6 months, including lubricants and remote control.

CursorCare E-Mail: service_sports@163.com

© 2023 ROBORE. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.