1. Important Safety Warnings
IMPORTANT! Read carefully and keep for future reference.
Please mind potential fire risk and strictly follow the instruction manual for charging and storage. While using the product, please wear protective equipment and fully comply with the applicable law and regulations.
- Always wear a helmet and appropriate safety gear (e.g., knee and elbow pads) when riding.
- Familiarize yourself with local laws and regulations regarding electric scooters before riding.
- Do not ride in adverse weather conditions (heavy rain, snow, ice) or on slippery surfaces.
- Regularly check the brakes, tires, and all fasteners before each ride.
- Avoid riding under the influence of alcohol or drugs.
- This product is designed for individuals aged 14 and above.
2. Package Contents
Ensure all items listed below are included in your package. If anything is missing or damaged, please contact customer support.

Figure: iScooter Y16 Package Contents
- 1. Scooter
- 2. NFC Key Cards (2 pieces)
- 3. Mirrors (2 pieces)
- 4. Front Wheel & Axle & Drum Brake
- 5. Left Shock Absorber & Trims
- 6. Front Basket & Mounting Kit
- 7. Saddle
- 8. Passenger Seat
- 9. Front Fender
- 10. Rear Fender
- 11. Rear Reflector
- 12. Drop Stand
- 13. Tools
- 14. Charger
- 15. User Manual & Safety Instructions
3. Product Overview
Familiarize yourself with the different parts of your iScooter Y16 electric scooter.

Figure: Labeled Parts of the iScooter Y16
- Saddle
- Passenger Seat
- Taillight
- Rear Fender
- Rear Reflector
- Shock Absorbers
- Drop Stand
- Footrests
- Battery Disconnect Switch
- Charging Port
- Mirrors
- Brake Levers
- Display
- Headlight
- Front Basket
- Suspension Fork
- Front Fender
4. Assembly Instructions
Before starting assembly, remove all items from the box and protective packaging. Place the scooter stably on a flat surface.
4.1. Install the Handlebar

Figure: Handlebar Installation
- Insert the handlebar post fully into the steerer tube.
- Adjust the handlebar so that it is parallel to the fork crown.
- Tighten the stem expander bolt securely.
4.2. Install the Display

Figure: Display Installation
Align the mounting holes of the display, then tighten the screws securely.
4.3. Install the Mirrors

Figure: Mirror Installation
- Remove the plastic plugs from the mirror mounting holes.
- Rotate the mirror stems into their mounts to the desired angle.
- Tighten the lock nuts and slide down the rubber covers to cover the lock nuts.
4.4. Install the Front Wheel

Figure: Front Wheel Installation
- Attach the drum brake assembly to the front wheel snugly.
- Place the front wheel between the fork legs, ensuring the pin on the inside of the left fork leg fully goes into the slot on the outside of the drum brake backing plate.
- Remove the nut and bushing from the front wheel axle.
- Pass the axle rod through the dropout of the left fork leg, bushing, wheel hub, and the dropout of the right fork leg, ensuring the flange on the axle is fully seated into the hole on the left fork leg.
- Tighten the nut securely.
4.5. Install the Front Fender

Figure: Front Fender Installation
Place the front fender between the fork legs and adjust so that the fork legs seat into the fender grooves. Slide the fender down the fork legs to align the mounting holes, then tighten the bolts securely.
4.6. Install the Shock Absorbers

Figure: Shock Absorber Installation
- Remove the front basket's bottom mounting plate from the rear left side of the frame.
- Install the left shock absorber with the position of its damper body/cylinder the same as that of the right shock absorber.
- Tighten the lower bolt and nut of the right shock absorber.
- Install the shock absorber trim on two sides as shown.
4.7. Install the Front Basket

Figure: Front Basket Installation
- Use the screw to secure the plastic accessory to the rear of the basket.
- Align the mounting holes of the front basket mounting plate and secure it with bolts.
- Attach the basket to the front of the steerer tube, ensuring the plastic accessory hooks onto the bracket on the steerer tube.
- Pass the bolts through the holes on the metal plate, then tighten the bolts securely.
- Tighten the bolts to secure the bottom of the basket in place.
- Use the plug to cover the screws in the slot.
4.8. Install the Drop Stand

Figure: Drop Stand Installation
Place the drop stand behind the rear wheel, adjust it so that the tabs on the stand hook the slots on two sides. Then, align the mounting holes and tighten the bolts securely.
4.9. Install the Passenger Seat

Figure: Passenger Seat Installation
- Attach the passenger seat to the rear rack with the three hooks beneath the seat engaging into the corresponding slots.
- Push the seat forward so that the mounting hole beneath the seat aligns with that on the rear rack.
- Firmly tighten the bolt to lock the passenger seat in place.
4.10. Install the Saddle

Figure: Saddle Installation
Align the three studs underneath the saddle with the mounting holes, attach the saddle to the mounting plate, and tighten the nut securely.
4.11. Install the Rear Fender & Footrests

Figure: Rear Fender and Footrest Installation
- Attach the rear fender to the rear fender as shown, pass the bolts through the reflector's mounting holes and those on the rear fender, and tighten the bolts and nuts with the supplied tools.
- Place the rear fender over the rear wheel, align the mounting holes on the front of the rear fender with those on the brackets, and tighten the bolts securely.
- Pass the bolts through the mounting holes of the footrests and then the rear fender, then tighten the bolts securely.
4.12. Pre-Ride Check
After assembling and before each ride, check the tires. If they feel soft or spongy, inflate them to the proper pressure.
5. Basic Operations
Video: iScooter Y16 Product Demonstration
5.1. Battery Disconnect Switch

Figure: Battery Disconnect Switch
The Battery Disconnect Switch is toggled to "OFF" during shipping to prevent battery drain.
- Toggle it to the “ON” position before each ride.
- Toggle it to the "OFF" position for long-term storage.
5.2. Power ON/OFF (NFC)

Figure: NFC Key Card Usage
Place the NFC Key Card flat against the front of the display to power on/off the scooter.
5.3. Headlight ON/OFF
Toggle the Headlight Switch to turn on/off the headlight and taillight simultaneously while the scooter is powered on.
5.4. Riding Mode
Press the "S" Button while the scooter is powered on to cycle through riding modes. The riding mode defaults to "1" after each restart.
5.5. Horn
Press or hold the "Horn" Button while the scooter is powered on.
5.6. Anti-Theft Alarm
Moving the scooter while it is powered off will trigger the anti-theft alarm.
5.7. P Mode (Parking Mode)
The scooter will enter the "P" mode every time you restart it. In this mode, it will not accelerate when you twist the throttle.
- To exit the “P” mode, squeeze the left or right brake lever. Then, you can twist the throttle to accelerate the scooter.
- The scooter will re-enter P mode after 20 seconds of inactivity.
6. Display and Controls
The iScooter Y16 features a large 4.5-inch round color LED screen for clear display of riding information.

Figure: Display Indicators
6.1. Display Indicators
- Headlight indicator
- Ready indicator
- Real-time Speed
- Riding Mode
- Battery Level
- Battery Voltage
- Fault Codes
- Total Mileage (Odometer)
6.2. Speed Levels
| Riding Mode | Max Speed (European) | Max Speed (North American) |
|---|---|---|
| 1 | 6 km/h | 9 mph |
| 2 | 10 km/h | 15 mph |
| 3 | 15 km/h | 21 mph |
| 4 | 25 km/h | 28 mph |
7. Charging the Battery
Proper charging practices ensure the longevity and safety of your scooter's battery.

Figure: Charging Port Location
- Fully charge the battery before first use.
- The scooter is fully charged when the charger indicator changes from red to green.
- With charging protection, the scooter will cut off charging automatically after a full charge. However, overcharging is not recommended.
- Keep the charging port cover closed when not charging to prevent dust and moisture ingress.
- The scooter cannot be turned on during charging for safety reasons.
8. Specifications
Below are the technical specifications for the iScooter Y16 electric scooter.

Figure: Key Specifications
8.1. European Specifications
| Feature | Value |
|---|---|
| Model | Y16 |
| Scooter Size | 143 x 69 x 107 cm |
| Weight | 36.3 kg |
| Battery Capacity | DC 48 V, 20 Ah |
| Range | 90-100 km * |
| Motor Power | 1200 W |
| Max Speed | 25 km/h |
| Max Load Capacity | 120 kg * |
| Recommended Age | 14+ |
| Charger Input | AC 100-240 V, 50/60 Hz |
| Charger Output | DC 54.6 V, 2 A |
| Charging Time | 9-10 h |
| Operating Temperature | 20°C-25°C |
| Storage Temperature | -20°C-40°C |
| Charging Temperature | 0°C-40°C |
| Waterproof Rating | IPX4 |
* About the range: Measured in a laboratory under 100% battery level condition. The range will differ depending on different factors, such as load, humidity, wind speed, and operation habits. The structure of this scooter is designed to support a maximum load of 120 kg. For the best riding experience, 70% of the maximum load is recommended.
8.2. North American Specifications
| Feature | Value |
|---|---|
| Model | Y16 |
| Scooter Size | 56.3 x 27.2 x 42 in (143 x 69 x 107 cm) |
| Weight | 76.1 lbs (34.5 kg) |
| Battery Capacity | DC 48 V, 20 Ah |
| Range | 56-62 miles (90-100 km) * |
| Motor Power | 1200 W |
| Max Speed | 28 mph (45 km/h) |
| Max Load Capacity | 264 lbs (120 kg) * |
| Recommended Age | 14+ |
| Charger Input | AC 100-240 V, 50/60 Hz |
| Charger Output | DC 54.6 V, 2 A |
| Charging Time | 9-10 h |
| Operating Temperature | 68°F-77°F (20°C-25°C) |
| Storage Temperature | -4°F-104°F (-20°C-40°C) |
| Charging Temperature | 32°F-104°F (0°C-40°C) |
| Waterproof Rating | IPX4 |
* About the range: Measured in a laboratory under 100% battery level condition. The range will differ depending on different factors, such as load, humidity, wind speed, and operation habits. The structure of this scooter is designed to support a maximum load of 264 lbs (120 kg). For the best riding experience, 70% of the maximum load is recommended.
9. Troubleshooting: Error Codes
The display may show error codes if an issue occurs. Refer to the table below for common error codes. If you encounter any of these or other error codes, please contact customer support for assistance.
| Error Code | Description |
|---|---|
| ECU | Motor Fault |
| Controller Fault | |
| Brake Fault | |
| Throttle Fault |
10. Maintenance
Regular maintenance ensures the optimal performance and longevity of your iScooter Y16.
- Cleaning: Wipe the scooter with a soft, damp cloth. Do not use high-pressure water or harsh cleaning agents.
- Tires: Check tire pressure regularly (refer to specifications for recommended pressure). Inspect tires for wear and tear or punctures.
- Brakes: Periodically check brake levers and cables for proper function. Ensure brakes respond effectively.
- Battery Care: Store the scooter in a cool, dry place. If storing for extended periods, ensure the battery is charged to about 50-70% and recharge every 30-60 days to prevent deep discharge.
- Fasteners: Regularly check all screws and bolts to ensure they are tight.
11. User Tips
- For optimal range, maintain consistent speed and avoid aggressive acceleration/braking.
- Utilize the front and rear baskets for groceries or personal items to maximize convenience.
- When parking, always use the drop stand to ensure stability and prevent accidental falls.
- Take advantage of the dual suspension system by adjusting your riding posture to absorb bumps effectively on uneven terrain.
12. Warranty & Support
12.1. Compliance Statements
FCC Statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not explicitly approved by the manufacturer could void your authority to operate this equipment.
ISED Statement: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
CE Warning: The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction. Children being supervised not to play with the appliance.
12.2. Disposal of Electrical and Electronic Equipment
The crossed-out garbage can symbol indicates that you are legally obliged to dispose of these devices separately from unsorted municipal waste. Disposal via the residual waste bin or the yellow bin is prohibited. If the products contain batteries or rechargeable batteries that are not permanently installed, they must be removed before disposal and disposed of separately as a battery.
12.3. Manufacturer Information
Manufacturer: Dongguan Yicheng Shengda Information Technology Co., Ltd.
Address: Room 301, No. 28, Houshan Road, Nanchongkou, Humen Town, Dongguan City, Guangdong Province, China
E-mail: support@e-scootworld.com
For the full text of the EU Declaration of Conformity, please contact the support team at the provided email address.