Haier PSR-K1 0034001009C

Contents

Haier Washing Machine Water Level Sensor Instruction Manual

Model: PSR-K1 0034001009C

1. Product Overview

This manual provides instructions for the installation, operation, maintenance, and troubleshooting of the Haier Washing Machine Water Level Sensor, model PSR-K1 0034001009C. This sensor is a critical component responsible for accurately detecting the water level inside your washing machine, ensuring proper operation during wash cycles.

Top view of the Haier washing machine water level sensor

Figure 1: Top view of the Haier washing machine water level sensor.

Haier washing machine water level sensor with its accompanying wiring harness

Figure 2: The water level sensor shown with its wiring harness.

2. Safety Information

Before proceeding with installation or maintenance, please read and understand the following safety precautions:

  • Always disconnect the washing machine from the power supply before attempting any installation, repair, or maintenance.
  • If you are not confident in performing the replacement, seek assistance from a qualified technician.
  • Handle the sensor and wiring carefully to avoid damage.
  • Ensure all connections are secure and properly insulated after installation.

3. Setup and Installation

This water level sensor is designed as a direct replacement part for compatible Haier washing machines. The installation process typically involves accessing the sensor compartment within the washing machine and replacing the old unit with the new one.

3.1. Required Tools

  • Screwdriver set (Phillips and flathead)
  • Pliers (optional, for stubborn connectors)
  • Multimeter (for testing, optional)

3.2. Installation Steps

  1. Disconnect Power: Unplug the washing machine from the electrical outlet and turn off the water supply.
  2. Access Sensor: Depending on your washing machine model, you may need to remove the top panel, back panel, or front panel to access the water level sensor. Refer to your washing machine's service manual for specific access instructions.
  3. Locate Old Sensor: Identify the existing water level sensor. It is typically a small, round or rectangular component with a pressure hose connected to it and electrical wires.
  4. Disconnect Old Sensor: Carefully disconnect the pressure hose and the electrical wiring harness from the old sensor. Note the orientation of the wiring if it's not keyed.
  5. Remove Old Sensor: Unmount the old sensor from its housing. This may involve unscrewing it or releasing clips.
  6. Install New Sensor: Mount the new PSR-K1 0034001009C sensor in the same position as the old one.
  7. Connect Wiring: Connect the wiring harness to the new sensor. Ensure the connection is firm and correct.
Side view of the water level sensor, showing the model number V13305 316 91 006 0034001009C

Figure 3: Side view of the sensor displaying its model and serial numbers.

Close-up of the wiring harness for the water level sensor

Figure 4: The wiring harness connector for the water level sensor.

  1. Connect Pressure Hose: Reattach the pressure hose to the new sensor. Ensure it is securely fastened and free from kinks or leaks.
  2. Reassemble: Reattach any panels removed during the process.
  3. Restore Power: Reconnect the washing machine to the power supply and turn on the water supply.
  4. Test: Run a short wash cycle to verify the sensor is functioning correctly and the machine fills and drains properly.

4. Operating Principles

The water level sensor (also known as a pressure switch) works by detecting the air pressure in a small air trap located at the bottom of the washing machine tub. As water fills the tub, it compresses the air in the trap, and this pressure is transmitted through a hose to the sensor. The sensor then converts this pressure into an electrical signal, which is sent to the washing machine's control board. The control board uses this signal to determine the current water level and to stop filling when the desired level is reached for a selected wash program.

5. Maintenance

The Haier water level sensor PSR-K1 0034001009C is a sealed unit and generally requires no direct maintenance. However, to ensure its longevity and accurate operation, consider the following:

  • Hose Inspection: Periodically check the pressure hose connected to the sensor for any kinks, cracks, or blockages. A damaged or blocked hose can lead to inaccurate water level readings.
  • Connection Check: Ensure the electrical connections to the sensor remain secure and free from corrosion.
  • Cleanliness: Keep the area around the sensor free from lint, debris, or moisture buildup.

6. Troubleshooting

If your washing machine exhibits water level-related issues after sensor replacement, consider the following troubleshooting steps:

SymptomPossible CauseSolution
Washing machine overfills or underfillsFaulty sensor, kinked/blocked pressure hose, loose wiring.Check pressure hose for obstructions. Verify electrical connections. If issues persist, the sensor may be faulty.
Washing machine does not fill with waterSensor not signaling correctly, water inlet valve issue, control board issue.Ensure water supply is on. Check sensor wiring. Consult a technician if other components are suspected.
Error code related to water levelSensor malfunction, wiring issue, control board issue.Refer to your washing machine's user manual for specific error code meanings. Check sensor connections.

If troubleshooting steps do not resolve the issue, it is recommended to contact a qualified appliance repair technician.

7. Specifications

FeatureDetail
Model NumberPSR-K1 0034001009C
CompatibilitySuitable for Haier washing machines (verify part number for specific model)
Dimensions (Approx.)Length: 15 cm, Width: 15 cm, Height: 15 cm
Weight (Approx.)0.01 kg
OriginMainland China
High-concerned chemicalNone

8. Warranty and Support

For warranty information, please refer to the terms and conditions provided by your original seller or retailer at the time of purchase. For technical support or assistance with installation, it is recommended to contact a certified appliance repair professional or the customer service department of your washing machine's manufacturer.

9. User Tips

No specific user tips are available from reviews or Q&A for this product at this time. Always ensure the washing machine is unplugged before attempting any inspection or repair.

© 2023 Haier. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.