1. Product Overview
This product consists of new original front earpiece receiver speakers designed for the Fossibot F113 and F106 PRO cell phone models. The earpiece speaker is a critical component responsible for delivering audio to your ear during phone calls. If you are experiencing issues such as no sound, low volume, or distorted audio from the earpiece during calls, replacing this part may resolve the problem.

Figure 1: Front view of the Fossibot F113/F106 PRO earpiece speaker.

Figure 2: Back view of the earpiece speaker, showing the electrical contact points.
2. Safety Information
- Always disconnect the phone's battery before performing any repairs to prevent electrical damage or short circuits.
- Use appropriate tools to avoid damaging the phone's components or casing.
- Handle small components with care. Static electricity can damage sensitive electronic parts. Consider using an anti-static wrist strap.
- If you are not confident in your ability to perform the repair, seek professional assistance.
3. Installation (Replacement)
Replacing the earpiece speaker requires disassembling your phone. This process should only be attempted by individuals with experience in phone repair or a good understanding of electronics. Incorrect installation can lead to further damage to your device.
Required Tools (Not Included):
- Small Phillips head screwdriver
- Prying tools (plastic spudger, opening picks)
- Tweezers
- Heat gun or hairdryer (optional, for adhesive removal)
- Anti-static wrist strap (recommended)
Installation Steps:
- Power Off Device: Ensure your Fossibot F113 or F106 PRO is completely powered off before beginning.
- Remove SIM Tray: Eject the SIM card tray.
- Disassemble Phone: Carefully open the phone casing. This typically involves removing screws and gently prying open the back cover or screen assembly. Refer to specific disassembly guides for your phone model if available.
- Disconnect Battery: Locate and disconnect the battery connector from the motherboard to prevent accidental power-on or short circuits.
- Locate Earpiece Speaker: Identify the existing earpiece speaker, usually located at the top of the phone's front frame or screen assembly.
- Remove Old Speaker: Gently remove the old earpiece speaker. It may be held in place by adhesive or small clips. Use tweezers or a spudger.
- Install New Speaker: Position the new earpiece speaker in its designated slot. Ensure the contact points align correctly with the corresponding pads on the phone's circuit board.
- Reassemble Phone: Carefully reassemble your phone by reversing the disassembly steps. Ensure all connectors are securely attached and screws are tightened appropriately.
- Test Functionality: Power on your phone and test the earpiece speaker by making a phone call.

Figure 3: Example of an earpiece speaker correctly positioned within the phone's internal chassis (indicated by red box and arrow).
4. Operation
The earpiece speaker operates automatically when you make or receive a phone call. It converts electrical audio signals into sound waves, allowing you to hear the other party during a conversation. No user configuration is required for its basic operation.
5. Maintenance
As a sealed internal component, the earpiece speaker requires minimal maintenance. To ensure its longevity and optimal performance:
- Keep Clean: Regularly clean the earpiece grille on your phone's exterior to prevent dust and debris from accumulating and obstructing sound. Use a soft, dry brush or compressed air.
- Avoid Liquid Exposure: Protect your phone from water and other liquids, as moisture can damage the speaker and other internal components.
- Prevent Physical Damage: Avoid dropping your phone or subjecting it to impacts that could dislodge or damage the speaker.
6. Troubleshooting
If you encounter issues after replacing the earpiece speaker, consider the following troubleshooting steps:
- No Sound / Low Volume:
- Double-check that the speaker is correctly seated and its contact points are making firm connection with the motherboard.
- Ensure the phone's volume is turned up during a call.
- Verify that the phone's audio settings are not configured for speakerphone or Bluetooth output.
- Re-open the phone and inspect for any loose connections or debris obstructing the speaker's path.
- Distorted Sound:
- Ensure the speaker grille is clean and free of debris.
- Check for any physical damage to the speaker itself or its surrounding components.
- Confirm the speaker is correctly installed and not pressing against other internal parts.
- No Change After Replacement:
- The original issue might not have been the earpiece speaker. Other components like the audio IC on the motherboard or the flex cable connecting the speaker could be faulty.
- Ensure the replacement part itself is not defective (though unlikely for new original parts, it can happen).
7. Specifications
| Feature | Detail |
|---|---|
| Product Type | Front Earpiece Receiver Ear Speaker |
| Compatibility | Fossibot F113, Fossibot F106 PRO |
| Quantity per Lot | 2 Pieces |
| Origin | Mainland China |
| Certification | None |
| Package Weight | Approx. 0.1 kg |
| Package Dimensions | Approx. 10cm x 10cm x 10cm |
8. User Tips
- Pre-test: Before fully reassembling your phone, it is highly recommended to connect the new earpiece speaker and the battery, then briefly power on the phone to test the speaker's functionality. This can save significant time if the part is faulty or incorrectly installed.
- Document Disassembly: Take photos or videos during the disassembly process to help remember the placement of screws and components for reassembly.
- Organize Parts: Keep track of all screws and small parts, perhaps using a magnetic mat or labeled containers, as they often vary in size and length.
9. Warranty and Support
For any questions regarding the product, installation, or potential defects, please contact the seller directly through the platform where the purchase was made. Keep your order details readily available for faster assistance.