HGLRC Draco FPV HD VTX System

Contents

HGLRC Draco FPV HD VTX System User Manual

Model: Draco FPV HD VTX System (A1 LITE+, A1 PRO, A2 PRO, Ground Unit)

1. Introduction

The HGLRC Draco FPV HD VTX System is a high-performance digital video transmission system designed for FPV (First Person View) drones and other remote-controlled vehicles. It offers high-definition video transmission, low latency, and ultra-long distance capabilities, operating on the 5.8GHz frequency band with up to 1W power output. This manual provides essential information for the safe and effective use of your Draco FPV HD VTX System, covering its components, specifications, setup, operation, and maintenance.

HGLRC Draco FPV HD VTX System components overview

Figure 1: HGLRC Draco FPV HD VTX System Components

2. Safety Information

Please read and understand all safety warnings before operating the HGLRC Draco FPV HD VTX System. Failure to follow these instructions may result in injury, damage to the product, or other property.

  • Power Supply: Ensure the power supply voltage is within the specified range (8-30V for Air Unit, 8-36V for Ground Unit). Incorrect voltage can cause permanent damage.
  • Antenna Connection: Always connect the antennas to both the Air Unit and Ground Unit before powering on. Operating without antennas can damage the VTX module.
  • Heat Dissipation: The VTX system can generate significant heat, especially at higher power outputs. Ensure adequate airflow and avoid enclosing the units in confined spaces without ventilation.
  • Line of Sight: For optimal performance and safety, maintain a clear line of sight between the Air Unit and Ground Unit antennas during operation.
  • Local Regulations: Always comply with local laws and regulations regarding FPV operation, frequency usage, and power output.
  • Handling: Handle electronic components with care to avoid electrostatic discharge (ESD) damage.

3. Package Contents

The HGLRC Draco FPV HD VTX System comes in different versions (A1 LITE+, A1 PRO, A2 PRO, Ground Unit). Please verify the contents of your package against the list below. Note that the specific components may vary slightly depending on the version purchased.

Package contents for A1 LITE+, A1 PRO, A2 PRO versions

Figure 2: Package Contents Overview

Table 1: Package Contents by Version
Product A1 Camera A2 Camera Air Unit Cable VTX Antenna Multi-hole Camera Adapter
A1 LITE+ ✓ LITE+ Air Unit 2 pcs 2 pcs ✓
A1 PRO ✓ PRO Air Unit 2 pcs 2 pcs ✓
A2 PRO ✓ PRO Air Unit 2 pcs 2 pcs ✓

Note: The Ground Unit is sold separately and includes the Ground Unit itself, 2 VTX antennas, and a power cable.

4. Product Overview and Dimensions

Understanding the physical characteristics of your Draco FPV HD VTX System components is crucial for proper installation and integration into your FPV setup.

4.1 Ground Unit

Ground Unit dimensions 70x100x20mm, 78g

Figure 3: Ground Unit Dimensions (Approx. 70x100x20mm, Weight: Approx. 78g)

Note: Both the Ground Unit and the A1 LITE+/A1 PRO/A2 PRO VTX (Air Unit) use SMA female interfaces for antenna connection.

4.2 Cameras and Air Units

Camera and Air Unit dimensions for A1/A2 Cameras, Multi-hole Camera Adapter, LITE+ Air Unit, PRO Air Unit

Figure 4: Camera and Air Unit Dimensions

  • A1 Camera: 14x14x17mm, Mounting Hole Spacing: 14mm, Screw Hole Spacing: Single hole fixing.
  • A2 Camera: 19x19x29mm, Mounting Hole Spacing: 19mm, Screw Hole Spacing: 6.5mm.
  • Multi-hole Camera Adapter: Includes left and right pieces, one each. Mounting hole spacing: 20mm/Screw hole spacing: 16mm. Adapter weight: ≈4g. Compatible with most mainstream frames.
  • LITE+ Air Unit: 32x32x10mm, Mounting Hole Spacing: 20mm/25.5mm.
  • PRO Air Unit: 32x32x18mm, Mounting Hole Spacing: 20mm/25.5mm.

4.3 Total Product Weights

Total weights for LITE+ Air Unit, A1 PRO Air Unit, A2 PRO Air Unit, and Ground Unit

Figure 5: Total Product Weights

  • LITE+ Air Unit total Weight: 53g
  • A1 PRO Air Unit total Weight: 59g
  • A2 PRO Air Unit total Weight: 75.3g
  • Ground Unit total Weight: 193.1g

5. Specifications

Detailed technical specifications for the HGLRC Draco FPV HD VTX System components are provided below.

Detailed parameter tables for Air Unit (A1 LITE+, A1 PRO, A2 PRO) and Ground Unit

Figure 6: Parameter Tables for Air Unit and Ground Unit

5.1 Air Unit Specifications

Table 2: Air Unit Parameter Table
Parameter Draco A1 LITE+ Draco A1 PRO Draco A2 PRO
Power <30dBm (FCC) <30dBm (FCC) <30dBm (FCC)
Air Unit Power Supply 8-30V 8-30V 8-30V
Air Unit Mounting Hole Spacing 20mm/25.5mm 20mm/25.5mm 20mm/25.5mm
Air Unit Dimensions 32x32x10mm 32x32x10mm 32x32x18mm
Camera Mounting Hole Spacing 14mm/20mm 14mm/20mm 19mm
Antenna Dual antenna Dual antenna Dual antenna
Coax length ≈160mm ≈160mm ≈140mm
Air Unit Weight ≈30g (Without antenna) ≈36g (Without antenna) ≈42g (Without antenna)
FOV 170° 170° 160°
Resolution 1080P 1080P 1080P
Frame Rate 60fps 60fps 60fps
Aspect Ratio 4:3/16:9 4:3/16:9 4:3/16:9
OSD Data BF/INAV (MSP) BF/INAV (MSP) BF/INAV (MSP)
Air Unit SH1.0-6pin SH1.0-6pin SH1.0-6pin

5.2 Ground Unit Specifications

Table 3: Ground Unit Parameter Table
Parameter Draco Ground Unit
Dimensions 70x100x20mm
Power Supply DC Interface 8-36V
Weight ≈78g
Ground Unit Video Output HDMI interface
Antenna connector Dual SMA female connector
Mounting method 1/4 Nut
TF Slot Slot

6. Setup Instructions

This section details the steps for connecting and configuring your HGLRC Draco FPV HD VTX System. Refer to the comprehensive diagram (Figure 7) for visual guidance on wiring and settings.

Comprehensive diagram including connection diagrams, OSD settings, VTX settings, binding steps, and firmware upgrade instructions

Figure 7: Detailed Setup and Configuration Diagram

6.1 Connection Diagram (Refer to Figure 7, top-middle section)

Carefully follow the wiring instructions for both the Air Unit and Ground Unit:

  • Air Unit Wiring: Connect the Air Unit to your flight controller (FC) and camera using the provided cables. Ensure correct polarity for power (VCC, GND) and proper connection for data (TX, RX for OSD/MSP) and camera video input.
  • Ground Unit Wiring: Connect the Ground Unit to a suitable power source (8-36V DC) and your display device (e.g., FPV goggles, monitor) via the HDMI interface.
  • Antennas: Always attach the VTX antennas securely to both the Air Unit and Ground Unit before powering on.

6.2 OSD Settings (Refer to Figure 7, middle section)

The Draco system supports OSD (On-Screen Display) data via BF/INAV (MSP). Configure your flight controller's OSD settings to display relevant flight information on your FPV feed.

  • Ensure MSP is enabled on the UART port connected to the Air Unit.
  • Use your flight controller's configurator software (e.g., Betaflight Configurator, INAV Configurator) to customize OSD elements.

6.3 VTX Settings (Refer to Figure 7, middle section)

Adjust VTX parameters such as channel, band, and power output. These settings can typically be changed via the OSD menu using your flight controller's stick commands or through the flight controller configurator.

  • Access the VTX settings menu through your OSD.
  • Select the desired channel and band.
  • Choose the appropriate power level (e.g., 25mW, 200mW, 500mW, 1W) according to local regulations and your flying environment.

6.4 Binding Steps (Refer to Figure 7, lower-middle section)

To establish a connection between the Air Unit and Ground Unit, follow these binding steps:

  • Power on both the Air Unit and Ground Unit.
  • Initiate binding mode on the Ground Unit (specific button press or menu option, refer to Figure 7).
  • Initiate binding mode on the Air Unit (specific button press or sequence, refer to Figure 7).
  • Wait for the units to bind. An indicator light or on-screen message will confirm successful binding.

6.5 Firmware Upgrade (Refer to Figure 7, bottom section)

Periodically check for and install firmware updates to ensure optimal performance and access new features.

  • Download the latest firmware from the official HGLRC website.
  • Connect the unit (Air Unit or Ground Unit) to your computer using a USB cable (if applicable) or a dedicated flashing tool.
  • Follow the instructions provided with the firmware update utility to flash the new firmware.

7. Operating Instructions

Once the system is set up and bound, operating the HGLRC Draco FPV HD VTX System is straightforward:

  • Power On: Ensure all connections are secure and antennas are attached. Power on your FPV drone (Air Unit) and then your Ground Unit/display device.
  • Verify Signal: Check your display for a clear video feed. If the signal is poor or absent, re-check VTX settings (channel, band, power) and antenna connections.
  • OSD Monitoring: Utilize the OSD to monitor critical flight data such as battery voltage, RSSI, and flight mode.
  • Recording (if applicable): If your Ground Unit or Air Unit supports onboard recording, ensure it is activated before flight if you wish to capture footage.
  • Power Off: Always power off the Air Unit (drone) first, then the Ground Unit/display device.

8. Maintenance

Proper maintenance will extend the lifespan and ensure reliable performance of your Draco FPV HD VTX System:

  • Cleaning: Keep the units clean and free from dust, dirt, and moisture. Use a soft, dry cloth for cleaning. Avoid using solvents or harsh chemicals.
  • Antennas: Inspect antennas regularly for damage. Bent or broken antennas can significantly degrade video quality and range.
  • Cables: Check all cables for fraying or damage. Replace any damaged cables immediately.
  • Storage: Store the VTX system in a cool, dry place away from direct sunlight and extreme temperatures.
  • Firmware: Keep firmware updated to the latest version for optimal performance and bug fixes.

9. Troubleshooting

If you encounter issues with your HGLRC Draco FPV HD VTX System, refer to the following common troubleshooting steps:

Table 4: Common Troubleshooting Guide
Problem Possible Cause Solution
No video signal Incorrect channel/band, loose antenna, power issue, un-bound units. Verify VTX settings, check antenna connections, ensure units are powered and bound.
Poor video quality/short range Interference, low VTX power, damaged antennas, obstructions. Change VTX channel/band, increase VTX power (if legal), replace damaged antennas, fly in open areas.
OSD not displaying Incorrect FC wiring, MSP not enabled, OSD disabled in FC configurator. Check wiring between Air Unit and FC, enable MSP on the correct UART, enable OSD in Betaflight/INAV configurator.
Unit overheating Insufficient airflow, high power output in confined space. Ensure adequate ventilation, consider lowering VTX power if not needed, avoid prolonged ground testing at high power.

If the problem persists after trying these steps, please contact HGLRC customer support.

10. User Tips

  • Antenna Placement: For best signal, ensure your Air Unit antennas are positioned away from carbon fiber frames and other electronics. On the Ground Unit, position antennas for maximum reception.
  • Power Management: While the system supports 1W output, use the lowest power setting necessary for your flight environment to minimize heat generation and potential interference.
  • Cable Management: Secure all cables to prevent them from interfering with propellers or other moving parts, and to reduce strain on connectors.

11. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the seller or visit the official HGLRC website. Keep your proof of purchase for warranty claims.

© 2023 HGLRC. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.