1. Product Overview
The Seauto SAT 20 Pro is a powerful cordless robotic pool cleaner designed for efficient and thorough cleaning of various pool types and surfaces. Featuring sonar precision, dual-engine efficiency, and a dual-brush system, it provides comprehensive cleaning for floors, walls, and waterlines.
2. Package Contents
Ensure all items are present in the package:
- 1 x Seauto SAT 20 Pro Device
- 1 x Charger
- 1 x User Manual
- 1 x Hook (for retrieval)
- 1 x Set of Filters
3. Specifications
| Feature | Specification |
|---|---|
| Applicable Pool Shapes | In-ground and above-ground pools (Round, Rectangle, Kidney, Irregular) |
| Applicable Pool Size (Max) | Up to 2150 sq ft (200 m²) |
| Water Depth Supported | 1.6 - 16.4 ft (0.5 - 5 m) |
| pH Value Supported | 7.0 - 7.8 |
| Filter Density | 250 µm |
| Debris Type | Leaves, Algae, Stones, Pollen, Soil, etc. |
| Battery Capacity | 7800mAh |
| Continuous Cleaning Time | Up to 3.0 hours |
| Charging Time | Approx. 2.5 hours |
| Motor Lifespan | 10,000 Hours |
| Suction Motor Quantity | 1 |
| Motor Power | 108W |
| Motor RPM | 3200 RPM |
| Flow Rate | 80 GPM |
| Suction Power | 45,000Pa (brushless) |
| Key Features | Cordless, Press & Go, Auto-Dock, Floor Cleaning, Wall Cleaning, Waterline Cleaning, Sonar Navigation, N-path Cleaning, App Control, 10-Second Swappable Battery System |
4. Setup
-
Initial Charging
Before first use, fully charge the robotic pool cleaner. Connect the charger to the device and a power outlet. The charging indicator will show the charging status. A full charge takes approximately 2.5 hours.
Figure 5: Quick Charging -
Filter Installation
Ensure the filter basket is correctly installed inside the cleaner. Refer to the 'Maintenance' section for details on accessing and securing the filter.
-
Placement in Pool
Gently lower the cleaner into the pool. Ensure it is fully submerged and air bubbles have escaped before starting operation.
5. Operating Instructions
-
Starting Operation (Press & Go)
With the cleaner submerged, simply press the Start button on the device. The cleaner will automatically begin its cleaning cycle based on its default or last selected mode.
-
Cleaning Modes
The Seauto SAT 20 Pro offers various cleaning modes for comprehensive coverage:
- Floor Mode: Focuses on cleaning the pool floor using intelligent N-path planning to ensure no areas are missed.
- Wall Mode: Engages the cleaner to climb and scrub pool walls and the waterline.
- All-Terrain Mode: Combines floor and wall cleaning for complete pool coverage.
Figure 6: Floor Mode Cleaning
Figure 7: Wall Cleaning
Figure 8: All-Terrain Mode Logic -
App Control (Optional)
For full customization and precise control, download the official Seauto app. The app allows you to select specific cleaning modes and monitor the cleaner's progress.
Figure 9: App-Controlled Cleaning -
Auto-Docking
When the battery is low, the cleaner will automatically navigate to a position where it can be easily retrieved.
-
Retrieval
Use the provided hook to safely retrieve the cleaner from the pool. Avoid pulling the cleaner by its tracks or brushes.
6. Maintenance
-
Cleaning the Filter Basket
After each cleaning cycle, remove and clean the filter basket. Open the cleaner's lid, extract the filter basket, and rinse it thoroughly with a hose to remove collected debris. Ensure the filter is completely clean before reinserting.
Figure 10: Easy Maintenance Steps -
General Cleaning
Periodically wipe down the exterior of the cleaner to remove any residue. Inspect the tracks and brushes for wear or trapped debris and clean as necessary.
-
Battery Care
Always fully charge the battery after each use. If storing the cleaner for an extended period, ensure the battery is charged to at least 50% and recharge every 3 months to prolong battery life.
-
Swapping the Battery (if applicable)
The Seauto SAT 20 Pro features a 10-second swappable battery system. If you have a spare battery, you can quickly swap it to extend cleaning time without tools.
Figure 11: 10-Second Swappable Battery System
7. Troubleshooting
-
Robot not climbing walls effectively:
Ensure the pool's slope gradient is less than 90 degrees. Some tiled surfaces might reduce grip. Check if the filter is clean, as a clogged filter can affect suction and climbing ability. Ensure the battery is fully charged.
-
Incomplete cleaning coverage:
Verify that the pool size is within the recommended maximum of 2150 sq ft. For larger pools or heavily soiled pools, multiple cleaning cycles or a battery swap might be necessary. Ensure no large obstacles are impeding the cleaner's path.
-
Robot stops unexpectedly:
Check the battery level. The robot will auto-dock when the battery is low. Ensure there are no large debris items or obstructions causing the robot to get stuck.
-
Poor suction or debris collection:
Clean the filter basket thoroughly. A clogged filter is the most common cause of reduced suction. Inspect the brushes for wear or damage.
8. User Tips
- For optimal wall climbing, ensure your pool's surface is suitable. Tiled pools may sometimes present challenges for wall adhesion.
- Regularly clean the filter basket after each use to maintain peak performance and suction power.
- Utilize the provided hook for easy and safe retrieval of the cleaner from the pool.
- For pools with many corners, the cleaner may require additional manual attention to ensure all areas are spotless.
- If you have a smaller pool (e.g., 10m³), a single charge might be sufficient for multiple cleaning cycles in floor mode.
9. Warranty and Support
The Seauto SAT 20 Pro comes with a 3-year protection plan, which includes full machine replacement. This ensures your pool stays clean without service delays or repair wait times.
For any issues, malfunctions, or warranty claims, please contact Seauto customer support or your original seller. Provide your purchase details and a description of the problem for prompt assistance.