GEYA GPS8-17/18

Contents

GEYA GPS8-17/18 Automatic Transfer Switch Instruction Manual

Models: GPS8-17 (Dual Power) and GPS8-18 (Triple Power)

1. Introduction

The GEYA GPS8 Series Automatic Transfer Switch (ATS) is a high-performance dual or triple power controller designed to guarantee power continuity for critical loads. Combining rapid switching capabilities with advanced digital protection, this device monitors voltage and current in real-time, automatically transferring the load to a backup power source (such as a generator, inverter, or secondary grid) when the main power fails or becomes unstable. Ideal for residential, commercial, and industrial applications, the GPS8 ensures your equipment remains safe and operational.

The GPS8-17 is a dual power supply automatic transfer switch, 63A AC220V (L1-N1, L2-N2). The GPS8-18 is a three-way power supply automatic transfer switch, 63A AC220V (L1, L2, L3-N).

GEYA GPS8-17 Dual Power and GPS8-18 Triple Power Automatic Transfer Switches
Figure 1: GPS8-17 Dual Power and GPS8-18 Triple Power Automatic Transfer Switches

2. Safety Information

  • Qualified Electrician Required: The products must be installed by qualified electricians. All electrical connections shall comply with appropriate safety standards.
  • No Isolation Function: This product does not have an isolation function. Always disconnect the superior MCB (Miniature Circuit Breaker) during maintenance to prevent electric shock.
  • Neutral Connection: For both GPS8-17 and GPS8-18 models, the neutral (N) poles are straight through to the load end N poles and are not cut off or converted with the switch. This is a critical design aspect for installation.

3. Product Features

  • Integrated Protection: Combines 2/3-way automatic power transfer with over/under voltage and overcurrent protection, enhancing load safety and reducing installation costs.
  • Real-time Monitoring: Digital display shows voltage and current values for easy observation and maintenance.
  • Flexible Settings: Configurable power-on delay, protection delay, transfer delay, and adjustable power priority (no rewiring needed).
  • Convenient Control: Panel button with 0.5s long-press anti-misoperation function to turn on/off load power (L line only).
  • Flame Retardant Shell: Constructed with flame retardant PA66 material to prevent spontaneous ignition.
  • DIN Rail Mounting: Designed for easy installation on a 35MM DIN rail (EN/IEC 60715) with securing clips and tunnel-type wiring ports for secure connections.
GEYA GPS8-18 80A Automatic Transfer Switch with features highlighted
Figure 2: GPS8-18 with key features: Overcurrent, Overvoltage, Undervoltage, Monitoring, Adjustable parameters, Digital display.
GEYA GPS8-18 63A features: LED Indication for Operating Voltage, 35MM Rail Mounting, Flame Retardant Shell
Figure 3: Detailed features including LED voltage indication, 35MM rail mounting, and flame retardant shell.

4. Specifications

ParameterSpecification
FunctionAutomatic Transfer Switch with Protection
Rated Supply VoltageAC220V (L1,L2,L3-N)
Rated Frequency45Hz ~ 65Hz
Operation Voltage Range80V ~ 400V (L-N)
Rated Operational Current63A, 80A (AC1)
BurdenAC max. 3VA
Over Voltage SettingOFF, 230V ~ 300V (Adjustable)
Under Voltage SettingOFF, 140V ~ 210V (Adjustable)
Over/Under Voltage Action Delay0.1s ~ 10s
Over Current Setting1A ~ 63A (or 80A)
Over Current Action Delay2s ~ 600s
Power-up Delay2s ~ 600s
Reset Time2s ~ 900s
Switching Time0s ~ 900s (Adjustable)
Measurement Error≤ 1%
Electrical Life (AC1)1 × 104
Mechanical Life1 × 106
Operating Temperature-20°C ~ +60°C
Storage Temperature-35°C ~ +75°C
MountingDIN Rail EN/IEC 60715
Protection DegreeIP40 (front panel), IP20 (terminals)
Overvoltage CategoryIII
Pollution Degree2
Dimensions82mm x 72mm x 68mm
Weight320g
CertificationCE
Technical parameters table and panel diagram from the user manual
Figure 4: Technical parameters and Panel Diagram (from original manual).
Dimensions of the GEYA GPS8-18 63A Automatic Transfer Switch
Figure 5: Dimensions of the GPS8-18 63A model.

5. Setup and Installation

Installation must be performed by a qualified electrician in compliance with all local and national electrical codes and safety standards.

5.1 Mounting

The GPS8 series ATS is designed for 35MM DIN rail mounting. Use the securing clips for easy installation.

  1. Ensure the back panel display is accessible.
  2. Press the latches on the device.
  3. Insert the device onto the DIN rail.
  4. Release the latches to secure the device.
35MM Standard Rail Installation of the ATS device
Figure 6: The ATS can be directly installed into a household lighting distribution box on a 35MM DIN rail.
Simple Installation steps for DIN rail mounting
Figure 7: Step-by-step guide for simple DIN rail installation.

5.2 Wiring

The GPS8-18 model can accept three input power sources. The upper end terminal is connected to the neutral wire of the three-phase power supply. L1, L2, and L3 are connected to the live wires of three separate power supplies. Connect the lower end to the output load.

Important Note on Neutral: For both GPS8-17 and GPS8-18, all neutral (N) poles are straight through to the load end N poles and are not cut off or converted with the switch. This means the neutral line is always connected, and only the live lines are switched.

Video 1: Usage demonstration of the GPS8-18 63A model, showing wiring and automatic switching between three power sources.

5.3 Wiring Diagrams

Below are example wiring diagrams for the GPS8-17 (Dual Power) and GPS8-18 (Triple Power) models. These diagrams illustrate power conversion scenarios.

Wiring diagram for GEYA GPS8-17 Dual Power Automatic Transfer Switch
Figure 8: Example wiring for GPS8-17. Scenario 1: Power conversion between photovoltaic inverter and mains power. Scenario 2: Power conversion between mains and backup power sources such as generators.
Wiring diagram for GEYA GPS8-18 Triple Power Automatic Transfer Switch
Figure 9: Example wiring for GPS8-18. Scenario 1: Power conversion between photovoltaic inverter, mains power, and generator. Scenario 2: A power consumption scenario in which different phases are used as single-phase power supplies in a three-phase power system (equivalent to phase selector function).

6. Operation

6.1 Panel Overview

Panel Diagram of the GEYA ATS with indicators and buttons
Figure 10: Panel Diagram showing select phase indicator, operating voltage/current values, fault indicator, and control buttons.
  • Power Button (Power button icon): Used to manually turn on or off the load. Press and hold for 0.5 seconds to activate.
  • Setting Button (M button icon): Press and hold for 3 seconds to enter the setting mode. After modifying, press and hold for 3 seconds to save.
  • Up Arrow Button (Up arrow button icon): Used to increase the value when setting parameters.
  • Down Arrow Button (Down arrow button icon): Used to reduce the value when setting parameters.

6.2 Power-on and Reset Delay

During power-on or fault reset, the product will display a countdown. Once the countdown ends, the device will enter its normal running state.

6.3 LED Status Indicators

  • LED: L1/L2/L3: Indicates if the corresponding phase is selected or not.
  • LED: FLT: Indicates voltage fault recovery delay in progress, or if L1, L2, L3 voltages are all faulty, or a contact disconnection fault.

7. Parameter Setting

To enter parameter setting mode, press and hold the 'M' key for 3 seconds. Use the up and down arrow keys to adjust values. Press and hold 'M' for 3 seconds again to save changes and exit, returning to running mode. If no key is operated for 60 seconds, the device will automatically exit setting mode without saving changes.

Flowchart for parameter setting on GEYA GPS8-18
Figure 11: Parameter setting flowchart for GPS8-18, showing adjustable settings for overvoltage, undervoltage, overcurrent, and various delays.
Detailed parameter setting instructions from the user manual
Figure 12: Detailed parameter setting instructions and factory default values.

7.1 Factory Settings

ParameterRangeStep valueFactory settings
Over voltage valueOFF, 230V~300V1V275V
Over voltage recovery value225V~295V1V265V
Under voltage value140V~210V, OFF1V175V
Under voltage recovery value145V-215V1V180V
Voltage fault action time0.1s~10s0.1s0.5s
Over current valueOFF, 1A~63A0.1A60A, 80A
Over current action delay2s~600s1s5s
Power on delay time2s~600s1s5s
Reset time2s~900s1s10s
Switching time0s~900s—0s
Fault resetON-OFF—ON
Priority phaseL1-L2-L3-AUTO—L1

8. Applications

The GEYA GPS8 ATS is suitable for a wide range of applications requiring uninterrupted power supply and protection against voltage and current fluctuations.

Wide Range of Applications for GEYA ATS: Commercial, Hospitals, Data Centers, Industrial Facilities, Telecom Hubs
Figure 13: Examples of applications including Commercial buildings, Hospitals, Data Centers, Industrial Facilities, and Telecom Hubs.

9. Troubleshooting

If you encounter issues with your GEYA GPS8 ATS, refer to the following common problems and solutions:

  • Slow Switching / Outputs Reboot: If the device exhibits slow switching between lines or causes outputs to reboot, check the configured 'Switching Time' and 'Power-on Delay' parameters. Adjust these settings as needed (refer to Section 7: Parameter Setting).
  • Unexpected Neutral Behavior: Remember that the neutral (N) poles are always straight through and not switched. If your setup requires a switched neutral, this device may not be suitable. Ensure your wiring accounts for this design.
  • Fault Indication: If the FLT LED is on, check the voltage levels of L1, L2, L3. It may indicate a voltage fault recovery delay, all voltages being faulty, or a contact disconnection fault.
Functions Diagram showing fault reset and overcurrent fault logic
Figure 14: Functions Diagram illustrating fault reset logic and overcurrent fault behavior.

10. User Tips

  • Verify Neutral Connection: Always double-check that your neutral wiring is correctly configured, understanding that the N poles are straight through and not switched by the device.
  • Parameter Customization: Take advantage of the flexible parameter settings to fine-tune the device's response to your specific power supply conditions and load requirements.
  • Professional Installation: For optimal performance and safety, always have the device installed by a certified electrician.

11. Maintenance

Regular maintenance is crucial for the longevity and reliable operation of your ATS. Always ensure power is disconnected before performing any maintenance.

  • Disconnect Power: Before any maintenance, always disconnect the superior MCB (Miniature Circuit Breaker) to ensure no power is supplied to the ATS.
  • Visual Inspection: Periodically inspect the device for any signs of damage, loose connections, or overheating.
  • Cleaning: Keep the device clean and free from dust and debris. Use a dry, soft cloth for cleaning.

12. Disposal

All electrical waste should be disposed of in compliance with current WEEE (Waste Electrical and Electronic Equipment) regulations. Do not dispose of electrical appliances with unsorted municipal waste; use separate collection facilities. Contact your local government for information regarding available collection systems.

13. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the manufacturer or your authorized dealer. Ensure you have your product model number and purchase details available.

Contact Information:

GEYA ELECTRICAL CO.,LTD
Wenzhou Brige Industrial Zone, Beibaixiang Town,
Yueqing, Zhejiang, China 325603
Mobile: 0086-13567770207
E-mail: sale@cngeya.com
Web: www.geya.net

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.