Product Introduction
The Seauto SAT 40 is an advanced cordless robotic pool cleaner designed for efficient and thorough cleaning of swimming pools up to 300 m² (3230 sq.ft). It features AI sonar navigation, multiple cleaning modes, and a long-lasting rechargeable battery.
Safety Warnings and Precautions
PLEASE READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE USE.
- Use the device only according to these safety instructions. The manufacturer is not liable for any loss or injury caused by improper use.
- Use only the original battery and battery charger provided by Seauto.
- Keep the device out of reach of children and vulnerable persons. Children should not perform cleaning or maintenance tasks.
- Be careful when handling the battery casing to avoid fire and/or burns. Do not open, crush, or place near heat sources.
- Do not insert hands or fingers into the impeller motor area.
- Remove the pool cleaner from the pool before anyone enters the water.
- Always switch OFF the device before cleaning filters or examining the robot.
- Be careful when lifting the device to avoid bodily injury.
- Do not use the device or its battery if there is any mechanical damage.
- Do not use an extension cord to connect the battery charger to the electric socket. Use only an appropriately located power outlet.
- If the power cord is damaged, the entire charger must be replaced with an original part.
- Place the battery charger at least 3.5 m (12 ft) from the pool edge during operation.
- Place the battery charger at least 11 cm (4 in) above the ground to protect users against electric shock.
- Use a Residual Current Device (RCD) with a rated residual operating current not exceeding 30mA to power up the battery charger.
- The Lithium-Ion battery should be recycled at a certified battery electronics recycler. Batteries should NOT be discarded as waste or placed in municipal recycling bins. Do not disassemble the battery.
- Only for use in swimming pool water. Do not use out of water.
- Do not use when people or animals are in the pool.
- Do not let children play with the device.
- Unplug the device from the power supply before any cleaning or maintenance operation.
- Do not charge the product immediately after use and ensure that the charging port is completely dry.
- Do not expose the battery to a heat source or fire.
- Do not immerse or expose the charger to rain.
- When using the product, always make sure to insert the battery correctly to ensure its water tightness.
Product Structure and Packaging List
Structure Overview
The Seauto SAT 40 features a robust design with tracks for mobility and an integrated cleaning system. The main components include the robot body, filter basket, and control panel.

Diagram of the Seauto SAT 40 robotic pool cleaner.
Packaging List
The product package includes the following items:
- 1 x Robotic Pool Cleaner Device
- 1 x Hook
- 1 x User Manual
- 1 x Charger
- Filters & Foam (Filter Basket, Cartridge, Foam)

Contents of the Seauto SAT 40 package.
Specifications
| Feature | Specification |
|---|---|
| Supported Water Depth | 1.6-9.8 ft (0.5-3 m) |
| Charger Input | 100-240 VAC, 50-60 Hz |
| Lithium Battery Capacity | 10400 mAh |
| Battery Runtime (Default Mode) | 2-3 hours (advertised 4 hours) |
| Charging Time | 5-5.5 hours (actual observed: >4 hours) |
| Filtration System | 294µm Filter Basket + Ultra-fine Foam (3.7L + 180 µm + 90 µm) |
| Movement Speed | 40-80 ft/min (12-24 m/min) |
| Smartphone Application | Android / iOS (SEAUTO IOT Mobile Application) |
| Connection Protocol | Bluetooth® |
| Dimensions (L x W x H) | 17.32 x 14.88 x 8.82 in / 44 x 37.8 x 22.4 cm |
| Net Weight | 19.8 lbs / 9 kg |
| Waterproof Rating | IP68 |
| Storage Temperature | 32 to 104°F (0 to 40°C) |
| Cleaning Modes | All-cover, Wall-only, Floor-only, Waterline-only |
| Applicable Pool Shapes | In-ground pools, above-ground pools with flat ground (Rectangle, Custom, Kidney, Curved) |
| Applicable Pool Size (Max) | Up to 300 m² (3230 sq.ft) |
| PH Value Supported | 7.0-7.8 |
| Debris Type | Leaves, Algae, Stones, Pollen, Soil, etc. |
| Lifespan | 10000 Hours |
| Removable Battery | Yes |
| Suction Motors Quantity | 4 |
| Motor Power | 320W |
| Flow Rate | 120 GPM (7200 GPH) |
| Other Features | Cordless, Press & Go, Auto-Dock When Low Battery |

The Seauto SAT 40 offers a 240-minute runtime and covers up to 3230 sq.ft. Charging takes approximately 5 hours.
LED Status Indicators
| LED Color | Solid Light | Flashing Light |
|---|---|---|
| Blue | Operating | Flashes once per second (Device idle, stays on continuously when powered on) |
| Red | Charging | Battery level is low |
| Green | Fully Charged | - |
| Purple | Device failed to escape obstacle | Device is shutting down |
| White | - | Firmware is updating |

Four-color indicator lights provide real-time status of the robot.
Cleaning Modes
The Seauto SAT 40 offers four versatile cleaning modes to suit your pool's needs. Modes can be selected via the APP or by pressing the button on the device.
| Mode | Coverage Area | Voice Reminder | Runtime |
|---|---|---|---|
| All-cover Mode | Covers all areas (floor, walls, waterline) | All-cover Mode | 2.5-3 hours |
| Wall Mode | Cleans walls only | Wall Only | 2.5-3 hours |
| Floor Mode | Cleans floor only | Floor Only | 3-3.5 hours |
| Waterline Mode | Cleans waterline only | Waterline Only | 2-2.5 hours |
Note:
- The default mode upon startup is All-cover Mode.
- For Floor-Only Mode, you can insert the foam into the debris bin to capture finest particles smaller than 180 microns.
- For All-cover, Waterline, and Wall modes, do not place the foam in the filter basket, as it may reduce the power needed for wall climbing.

The robot offers various cleaning modes for comprehensive pool care.
Setup and Operation
1. Charging the Robot
Connect the charger to the robot and a power source. The LED will show a solid red light during charging. Once fully charged, the LED will turn solid green, and the device will automatically shut down after 10 minutes.

Robot connected to charger, red LED indicates charging.

Robot fully charged, green LED.
2. Placing in the Pool
- Before turning on the device, ensure the Cartridge is removed to allow the machine sufficient power for wall climbing and optimal waterline cleaning.
- Reassemble the basket into the device.
- Press the button to turn it on. It will display a flashing blue light and announce: "Hello, I'm ready to work, Now it's All-cover Mode."
- Place the device into the pool, ensuring the water level is above the top of the machine for normal operation. When it begins cleaning, the LED will change to a solid blue light.

Placing the robot into the pool.
3. Removing from the Pool
Attach the hook (included in your package) to a compatible pole (not included). Use the pole to hook and lift the machine from the pool. Before cleaning the filter basket, press and hold the button to turn off the pool cleaner.

Easy retrieval of the robot from the pool.
4. Smart Features and Navigation
The SAT 40 utilizes AI sonar navigation and a built-in IMU chip for smart route planning, ensuring no missed spots regardless of your pool's shape. It can clean floors with a CROSS pattern and walls with an N-Path.

Smart route planning ensures comprehensive cleaning.

The robot's treads provide superior mobility over various pool features.
5. Using the SEAUTO IOT Mobile Application
Download the Seauto app from Google Play (Android) or the App Store (iOS). Before connecting, ensure your phone's location and Bluetooth are enabled, and keep your phone within 16.4 feet (5 meters) of the robot for a stable connection.
Product demonstration video showing cleaning modes, navigation, and ease of use, including app control.
Maintenance
1. Cleaning the Filter Basket After Use
Clean the filter basket before it dries out. Ensure the machine is turned off.
- Press the switch to ensure the machine is turned off.
- Open the cover and remove the filter screen.
- Open the lid of the filter basket.
- Release the buckle and remove the fastener from the debris bin.
- Place the foam into the debris bin (for Floor-Only mode).
- Press the fastener to secure the foam in place.
- Place the debris bin into the filter basket and reassemble the filter basket.

Diagram of the filter basket.

Steps for cleaning the debris bin.
2. Replacing the Battery
If the performance of a new battery is affected, let the machine sit for 2 days before replacement to ensure complete evaporation of moisture. Replace the battery as described below to maintain the pool cleaning robot in optimal cleaning condition.
- Remove the six screws securing the device and take out the old battery.
- Insert the new battery following the corresponding position of the old battery.
- Install, secure, and tighten the screws.
Note: Before placing the new battery, clean away any foreign objects such as water droplets, sand, etc., from the contact points.
Off-Season Storage
If the pool cleaner will not be used for an extended period, please follow these storage steps:
- Ensure there is no water inside the pool cleaner.
- Thoroughly clean the filter basket and debris bin, then reassemble them back in place.
- Store the pool cleaning robot in a protected location with a temperature between 5°C-45°C (41°F−113°F). Avoid direct sunlight, rain, or frost.
- Charge the pool cleaner once a month to protect the battery.
Troubleshooting and FAQs
- Q: Why does the pool cleaning robot not respond after being turned on?
- A: The battery may be depleted after prolonged transportation or storage. Please charge the device. The indicator light will remain solid red during charging.
- Q: Why can't it climb the wall?
- A1: It may be set to Floor-Only Mode. Connect it to the app and select the correct mode.
- A2: The debris bin may be inside the filter basket. Remove it to ensure sufficient power for wall climbing.
- A3: There may be debris or obstructions inside the filter basket. Remove and clean the filter basket.
- Q: Why does the pool cleaning robot fall when cleaning the waterline instead of moving down along the wall?
- A: In an infinity pool or a pool with raised edges near the waterline, the robot may fall more easily as it cannot perfectly adhere to the wall.
- Q: Why does the cleaner remain stationary or move slowly at the bottom of the pool?
- A1: It may be stuck on a floor drain. It will attempt to float autonomously to free itself. If still stuck after a few minutes, assist it using the pole.
- A2: If placed in a dirty pool, it may quickly collect a large amount of debris. Check and clean the filter basket if necessary.
- Q: Why does the front float while the rear remains on the floor?
- A: This is an intelligent function of our pool cleaner designed to help it escape from being stuck.
- Q: Why can't my phone connect to the robot?
- A: Follow these steps to connect to the pool cleaning robot:
- Keep the machine powered on.
- Check and/or enable Bluetooth on your phone.
- Ensure your phone is close enough to the pool cleaning robot (within 16.4 ft / 5 m).
- Q: Why doesn't the cleaner clean the walls or waterline All-cover Mode?
- A1: The filter basket may have collected too much debris, reducing its mobility.
- A2: The debris bin may be inside the basket. Remove it to ensure sufficient power for wall climbing.
- Q: How many smartphones can be connected to one pool cleaning robot?
- A: The pool cleaning robot can only be connected to one smartphone at a time. It cannot be connected to other smartphones. If you wish to connect a different smartphone, reset the pool cleaning robot or remove it from the app.
- Q: Why are there water droplets inside a newly purchased machine?
- A: Each machine undergoes rigorous pre-shipment testing, including underwater tests, which may leave a small amount of water inside. This is normal and safe for use.
- Q: Why does the pool cleaning robot automatically shut off after charging for several hours?
- A: It is designed to shut down automatically 10 minutes after a full charge to protect the battery and ensure its lifespan. You can leave it charging without safety concerns.
User Tips
- Battery Life & Charging: While advertised for 4 hours, actual runtime may be closer to 2.5-3 hours. Charging can take over 4 hours. Plan your cleaning sessions accordingly.
- Pool Compatibility: The SAT 40 is ideal for in-ground pools and above-ground pools with flat bottoms. It may struggle with sloped bottoms or diamond-tip pools, leading to random movements or getting stuck.
- Waterline Cleaning: In Waterline mode, the robot might get stuck on pool features like exhaust nozzles, lamps, or corners. Manual intervention may be required in such cases.
- Fine Debris Filtration: For very fine dust, the robot might not retain all particles, potentially clouding the water. Ensure regular filter cleaning.
- App Control: The mobile application allows mode selection. Note that advanced features like setting timers or stopping the robot remotely might not be available in the app.
Warranty and Support
Warranty Information
- 1-year warranty on the machine and 1-year warranty on the battery from the date of purchase.
- There is no extended warranty for consumables (filter net).
- The warranty is void if the product has been altered, misused, or repaired by unauthorized personnel.
- The warranty covers manufacturing defects only and does not cover damage from mishandling by the owner.
- The order number or record must be presented for any claim or repair during the warranty period.
- In accordance with French consumer and civil law, legal warranties apply in case of non-compliance or hidden defects.
Warranty Exclusions
The warranty does not cover:
- Improper or Inappropriate Use: Use in public/commercial pools, saltwater pools, pools with inappropriate chemicals, use outside recommended pH/temperature/chlorine levels, use out of water or in an empty/partially filled pool.
- Improper Maintenance and Storage: Lack of regular maintenance, storage in improper environments (freezing, excessive humidity, extreme heat, prolonged sun exposure), or damage caused by foreign objects in the pool.
- Physical or Cosmetic Damage: Damage due to impacts, drops, mishandling, scratches, cracks, aesthetic issues not affecting functionality, or water infiltration due to misaligned/non-original seals.
- Unauthorized Repairs or Modifications: Repairs/tampering by unauthorized personnel, disassembly without authorization, or use of non-original/non-certified spare parts.
- Electrical or Environmental Issues: Use with unsuitable electrical supply, damage from power surges/lightning/short circuits/faulty installation, or immersion of non-waterproof components.
- Normal Wear and Tear: Wear of consumable parts (brushes, filters, belts, wheels), gradual performance loss due to intensive use, or normal lifespan.
- Failure to Follow User Manual: Failure to follow usage, safety, or installation instructions.
- Force Majeure or Accidental Events: Damage from fire, flooding, earthquakes, vandalism, theft, or other unforeseeable external events.
Notice: Any warranty claim must be accompanied by proof of purchase, full compliance with the user manual, and may be subject to technical inspection.
Declaration of Conformity (CE)
Seauto declares that this product meets all the requirements of the applicable European directives 2014/35/EU (LVD); 2014/30/EU(EMC); 2011/65/EU (RoHS). N°1907/2006 (REACH).
Contact Information
For warranty issues, replacement parts, or further assistance, please contact Seauto:
- Phone: +1800-618-8968
- Email: support@seautorobots.com
- Operating Hours: Mon-Fri, 09:00-18:00 (EST)