Supstable S3 Lite

Contents

Supstable 2 in 1 Electric Pole Saw & Cordless Chainsaw

Model: S3 Lite

Supstable 2-in-1 Electric Pole Saw and Cordless Chainsaw with two batteries and two guide bars

Supstable 2-in-1 Electric Pole Saw and Cordless Chainsaw with included accessories.

Introduction

Please read this instruction manual thoroughly before using the product and keep it accessible for future reference.

Intended Use:

This equipment is suitable for gardening pruning, shrub pruning, twig pruning, and wood cutting. It is widely used in gardens, parks, farms, highways, pastures, orchards, barns, etc.

For additional information, a PDF version of this manual is available: User Manual (PDF)

Safety & Operation Guidelines

WARNING

Be sure to read and understand all safety instructions in this Operator's Manual, including all safety alert symbols such as "WARNING" and "CAUTION" before using this tool. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury.

For Optimal Performance, We Recommend:

  1. Battery Prep: Fully charge the battery before initial use.
  2. Chain Direction Check: Ensure the chain is installed correctly (cutting edge faces forward).
  3. Chain Tension Adjustment:
    • Keep the chain slightly loose (hand-pulling should expose 5 drive links).
    • Over-tightening (especially for brushless motors) may cause startup failure, increased friction, overheating, or motor damage.
  4. Lubrication Routine:
    • Apply lubricant to the guide bar groove and chain before use.
    • Re-lubricate every 3-5 cuts or press the oil bubble 2-3 times (automatic oilers exempt).
  5. Operation Sequence: Start the chainsaw first, then position it against the cutting area.
  6. Avoid Excessive Pressure: Do not force the saw during use. Over-pressing increases current, triggering motor/battery overheating protection (may cause shutdown).
  7. Chain Loosening: Normal during high-speed operation. Carry a chain adjustment tool (excludes tool-free tensioning models).
  8. Avoid Forked Branches: Hardwood forks may damage the chain.
  9. Branch Size Limits:
    • Do NOT cut branches ≤2cm diameter (high kickback risk).
    • Branches ≤5cm may cause severe vibration (secure small branches first).
  10. Oil Tank Level: Fill to two-thirds max. Press oil bubble 2-3 times per 3-5 cuts. Avoid over-pumping to prevent leaks.
  11. Emergency Shutdown Causes:
    • Motor Overheat Protection (120°C limit): Cool for ~20 minutes.
    • Battery Low/Over-Discharge: Replace battery.
    • Battery Overheat: Cool in shade for 20-30 minutes.
    • Battery Charging Lock (>45°C): Cool to <45°C before charging.

Pole Chainsaw-Specific Guidelines:

  1. Safety Gear Required: Safety harness, anti-slip shoes, goggles, cut-resistant gloves, helmet (against falling branches).
  2. Voltage Requirement: Use only at 19.5-21V; never below 19.5V.
  3. Pre-Use Lubrication: Mandatory for pole operation.
  4. Pole Inspection:
    • Confirm all telescopic sections are locked securely.
    • Verify angle adjustment button functions smoothly and locks firmly.
  5. Large Branch Cutting (>5cm): Cut from the outer end in sections. Never cut near the trunk first. Max diameter: 10cm (heavy branches pose drop hazards).
  6. Stable Posture:
    • Stand with feet apart on stable ground (no ladders/unsteady platforms).
    • Grip handles with both hands (right hand dominant). No single-hand use!
  7. Cutting Angle Warning: Never touch branches with the tip (kickback risk!).
  8. Operator Position: Maintain a 60-90° angle to the pole. Never stand directly under branches.
  9. Worksite Safety:
    • Clear area of people/pets within 3-meter radius.
    • Check for overhead wires. Adjust stance to avoid debris blowing toward face.
  10. Usage Control:
    • Limit continuous cutting to 10-15 minutes to prevent motor overheating.
    • Pause if battery overheats.
  11. Pole Saw Start Order: Start the machine before positioning the blade.
  12. Proper Handling: Let the saw's weight do the work—gently support the pole. Forcing it downward may cause jams or unsafe branch drops.
  13. Power Loss Note: Extended poles reduce efficiency due to voltage drop (e.g., 20V battery → 19V at tip).
  14. Post-Operation Protocol:
    • Battery Care: Remove battery post-use; avoid high-temperature storage (e.g., hot cars). Store long-term at ≥60% charge (never full/empty).
    • Maintenance: Clean resin/sawdust from chain/guide bar; apply rust-proof oil. Tighten all screws, especially pole joints.
    • Storage: Attach chain guard. Store in dry, child-proof area.
  15. Prohibited Actions (Extreme Risk!):
    • No use in rain/humidity (lithium battery fire hazard).
    • Never cut metal, stone, or frozen wood (chain breakage risk).
    • No branch dropping from height—use ropes or manual cleanup.
    • No battery modifications or overloading (explosion risk).
  16. Emergency Response:
    • Chain Jam: Power off immediately. Pry branch open with a wooden wedge.
    • Battery Fire: Use dry powder extinguisher (no water!).
    • Injury: Shut off power. Seek medical aid for chain-related wounds.

Core Risks: Kickback, battery hazards, falling from heights. Always follow safety protocols. Review instructional videos before first use.

Do not use the pole saw for felling or bucking. To prevent electrocution, do not operate within 50 ft. (15m) of overhead electrical lines. Keep bystanders at least 50 ft. (15m) Away.

Safety Symbols

This section depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate it.

SymbolMeaning
☞Refer to instruction manual/booklet
⚠General warning sign
👁Wear eye protection
🎧Wear ear protection
LWA 97 dBNoise sign (97 dB sound power level)
🥄Wear protective gloves
👟Wear safety footwear
🎩Wear head protection
🤝Always use chain saw two-handed
☔Do not expose to rain
⚡Remove plug from the mains immediately if the cable is damaged or cut.
☠Beware of chain saw kickback and avoid contact with bar tip.
♻Recycle Symbols
⚠DANGER - Keep hands away from blade
⚡Keep sufficient distance away from electrical power lines

Specifications

1) Chainsaw Specifications

AttributeValue
Motor TypeBrushless Motor
Rated Voltage20V
Weight (without battery)2.5kg (5.51lbs)
Weight (with one battery)2.8kg (6.74lbs)
Standard Guide Bar Length8 inch/6 inch
Chain Drive Links47DL/36DL
Chain Gauge And Pitch1/4" pitch 0.43" gauge
Battery Capacity4000mAh
Charging Time3-3.5 Hours
Input Voltage Single-Phase AC100-240 V
Input Frequency50/60 Hz
Chain Oil Tank Volume30ml
Working time with 4.0Ah Battery20mins
Recommended Operating Temperature5°F-104°F (-15°C-40°C)
Recommended Storage Temperature-4°F-158°F (-20°C-70°C)

2) Battery Charger Specifications

AttributeValue
ModelXH2100-1670WE
Input100-240VAC 50/60Hz 0.8A
Output21V ⏸ 1.67A

3) Battery Specifications

AttributeValue
ModelT1840-10
Rated Voltage18.5V ⏸
Capacity4000mAh
Watt Hours74Wh

Product Description and Components

Familiarize yourself with the components of your pole saw attachment:

  1. Chain
  2. Guide Bar
  3. Chain Guard
  4. Chain Tightening Knob
  5. Oil Tank
  6. Housing-Cover
  7. Safety Switch
  8. Start Button
  9. Hand Grip
  10. Hand Guard
  11. Battery Pack
  12. Drive Sprocket
  13. Fastening Bar Knob
  14. Chain Sheath
  15. Additional Handle
  16. Rotary Button
  17. Cam-locks
  18. Shoulder Strap Buckle
  19. Soft Sleeve
  20. Start Button (on pole)
  21. Hand Grip (on pole)
  22. Hand Guard (on pole)
  23. Battery Pack (on pole)

Refer to the diagram in the original manual (page 10) for visual identification of these parts.

Assembly

WARNING

If any parts are damaged or missing, do not operate this product until the parts are replaced. Use of this product with damaged or missing parts could result in serious personal injury.

WARNING

Do not attempt to modify this product or create accessories not recommended for use with this pole saw. Any such alteration or modification is misuse and could result in a hazardous condition leading to possibly serious personal injury.

To install and remove the chainsaw from the pole:

  1. Step 1: Fit the mini chainsaw unit to the extension pole.
  2. Step 2: Secure the safety catch until it clicks into position.
  3. Step 3: Release the catch by turning anti-clockwise.
  4. Step 4: Detach the mini chainsaw from the pole.

Installing the battery on the pole saw:

WARNING

Ensure that the exterior of the battery is clean and dry before connecting the charger or the machine.

Insert the battery into the machine's base as shown. Push the battery forward until it clicks into place. (Be careful to align the slots and inserts).

Removing the battery from the pole saw:

Press the battery release button. Remove the batteries from the pole saw.

Charging the battery with the charger:

Indicator LightStatus
RedCharging
GreenCharging completed

Replacement and Installation of Chains:

WARNING

Before performing any maintenance, make sure that the battery pack is removed.

WARNING

Always wear gloves when handling the bar and chain; these components are sharp and may contain burrs.

WARNING

Never touch or adjust the chain while the motor is running. The saw chain is very sharp, always wear protective gloves when performing maintenance to the chain.

  1. Step 1: Remove the housing-cover by turning the housing-cover knob counterclockwise.
  2. Step 2: Put the chain into the guide bar (The chain is sharp. Be careful not to cut your hand).
  3. Step 3: Please pay attention to the direction of the cutting tooth.
  4. Step 4: Install the bar and chain to the drive sprocket.
  5. Step 5: Install the housing-cover and housing cover knob. The nut on the housing-cover knob should be aligned with the fastening bar-nut-hole on the chain saw.
  6. Step 6: Adjust the housing-cover knob clockwise to tighten the housing-cover. The housing-cover cannot be fully tightened in this step; a slightly loose space is required to adjust the chain.
  7. Step 7: Clockwise fastening bar knob to tighten the chain. The chain cannot be installed too tightly.
  8. Step 8: Rotate the housing-cover knob to fix the guide bar completely.

Adjusting chain tightness:

If the chain loosens during use, the chain should be adjusted as follows:

  1. Step 1: Loosen the nuts on the chain cover slightly.
  2. Step 2: Adjust the chain tension knob.
  3. Step 3: Ensure 2-3 mm of a gap when you lift an individual link out of the bar. (Pull the chain to expose 4-5 drive links for optimal fit).
  4. Step 4: Tighten the nuts on the chain cover securely.

Adjusting the telescopic pole (optional):

Notice: When using the telescopic pole, it's best to remove the mini chainsaw from the pole.

Our 2-in-1 chainsaw can be used with a telescopic pole. To make the best use of the pole, please follow the instructions below:

  1. Step 1: Loosen the cam-lock nut.
  2. Step 2: Release the cam lock to extend the telescopic pole. Caution: Handle with care, and beware of the pole rebounding and potentially causing hand injuries.
  3. Step 3: Extend the telescopic pole to the desired length.
    • Note: Push two side bars towards the center to shorten the telescopic pole. Extend the length of the telescopic pole by pulling the side bar on both sides.
  4. Step 4: Engage the cam lock and tighten the cam-lock nut to secure the telescopic pole.
    • WARNING: Before using the telescopic pole, make sure it's properly secured.

Adjusting the angle of the chainsaw:

By pressing the button at the rotation position, you can freely adjust the angle of the chainsaw.

Operation

WARNING

Do not use any attachments or accessories not recommended by the manufacturer of this product. The use of attachments or accessories not recommended can result in serious personal injury.

Before each use, inspect the entire product for damaged, missing, or loose parts such as screws, nuts, bolts, caps, etc. Tighten securely all fasteners and caps and do not operate this product until all missing or damaged parts are replaced.

Applications:

You may use this product for:

  • Limbing
  • Pruning

Adding lubrication oil:

  1. Step 1: Loosen oil tank cap.
  2. Step 2: Pour the bar oil into the oil tank.
    • Tips: It is not recommended to fill the tank too full. (Oil is not included).
  3. Step 3: Tighten oil tank cap.

NOTE: After use, please pour out the oil in the oil tank of the chain saw to avoid chain saw oil leakage affecting the use of the chain saw.

Q: What kind of oil goes in a mini chain saw?
A: The regular chain&bar oil is acceptable, recommend Oregon 54-059 bar and chain oil.

Start the machine:

Tip: The switch-on method is the same for chain saws alone and pole saws in combination.

  1. Step 1: Press the button "A" to unlock the safety button. Press the button "B" at the same time to start the machine.
  2. Step 2: Release the button "A".

Video: Demonstration of the Supstable 2-in-1 Electric Pole Saw and Cordless Chainsaw in use, showing both pole and handheld operation, chain oiling, and battery installation.

Stop the machine:

Release the button "A" & "B" to stop the machine.

Cutting preparation:

WARNING

Refer to "Safety Instructions" earlier in this manual for appropriate safety equipment.

  • Make sure that the chain is properly mounted and correctly tensioned.
  • Lift the tip of the guide bar to check for any sagging in the chain. The chain is correctly tensioned when there is no sag on the underside of the guide bar and the chain is snug, but it can be turned by hand without binding. If the tension requires adjustment, refer to the “Replacement and Installation of Chains" section in the Assembly section of this manual for adjustment instructions.
  • Check the tension of the cover screw before use. If it is loose, securely tighten the cover screw by turning it clockwise.
  • Check the oil level and fill the tank as needed.
  • Check the sharpness of the cutting teeth on the saw chain.
  • Make sure the chain is well lubricated.
  • Wear non-slip gloves for maximum grip and protection.
  • Maintain a proper grip on the unit whenever the motor is running. Hold the unit firmly with both hands.
  • Never stand directly under the limb you are cutting.
  • Make sure that you have a secure and balanced footing. Watch out for obstacles such as tree stumps, roots and ditches, which could cause you to trip or stumble.

Limbing and pruning:

WARNING

Branches may fall in unexpected directions. Do not stand directly under the branch being cut.

  1. Plan the cut carefully. Be aware of the direction in which the branch will fall.
  2. The most typical cutting application is to position the unit at an angle of 60° or less, depending on the specific situation.
  3. As the angle of the pole-saw shaft to the ground increases, the difficulty of making the first cut (from the underside of limb) increases.
  4. Remove long branches in several stages.
  5. Cut lower branches first to allow the top branches more room to fall.
  6. Work slowly, keeping both hands on the saw with a firm grip. Maintain secure footing and balance.
  7. Keep the tree between you and the chain while limbing. Cut from the side of the tree opposite the branch you are cutting.
  8. Do not cut from a ladder; this is extremely dangerous. Leave such operations for professionals.
  9. Do not make the flush cut next to the main limb or trunk until you have cut off much of limb to reduce the weight. Following proper cutting procedures will prevent stripping the bark from the main member.

Maintenance

WARNING

When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage. To ensure safety and reliability, all repairs should be performed by a qualified service technician.

WARNING

Battery tools do not have to be plugged into an electrical outlet. To prevent serious personal injury, take extra precautions and care when performing maintenance, service or for changing the cutting attachment or other attachments.

WARNING

To prevent serious personal injury, remove the battery pack from the power head before servicing, cleaning, changing add-on attachments or when the product is not in use.

General Maintenance:

Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.

WARNING

Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken, or destroy plastic, which may result in serious personal injury.

WARNING

When cleaning the pole saw attachment, DO NOT immerse it in water or other liquids.

Cleaning:

  • After each use, remove the battery and clean debris from the chain and guide bar with a soft brush. Wipe the pole saw surface with a clean cloth moistened with a mild soap solution.
  • Remove the chain-sprocket cover, and then use a soft brush to remove debris from the guide bar, saw chain, sprocket and chain-sprocket cover.
  • Always clean out wood chips, saw dust, and dirt from the guide bar groove when replacing the saw chain.

Notice: All pole saw service, other than the items listed in these maintenance instructions, should be performed by competent pole saw service personnel.

Chain Maintenance:

WARNING

Before performing any maintenance, make sure that the battery pack is removed.

WARNING

Always wear gloves when handling the bar and chain; these components are sharp and may contain burrs.

Use only low-kickback chains on this saw. This fast cutting chain will provide kickback reduction when properly maintained. A properly sharpened saw chain cuts through wood effortlessly, even with very little pressure. Never use a dull or damaged saw chain. A dull saw chain cutter leads to increased physical strain, increased vibration load, unsatisfactory cutting results and poor wear. For smooth and fast cutting, the chain needs to be maintained properly. The chain requires sharpening when the wood chips that result from cutting are small and powdery, the chain must be forced through the wood during cutting, or the chain cuts to one side. During maintenance of your chain, consider the following:

  • Improper filing angle of the side plate can increase the risk of a severe kickback.
  • Raker (depth gauge) clearance. Too low increases the potential for kickback. Not low enough decreases cutting ability.
  • If cutter teeth have hit hard objects, such as nails and stones, or have been abraded by mud or sand on the wood, have the chain sharpened by a qualified service technician.

Notice: Inspect the drive sprocket for wear or damage when replacing the chain. If signs of wear or damage are present in the areas indicated, have the drive sprocket replaced by qualified service technician.

Sharpen the cutters:

Sharpen the cutters if it is not easy for the chain to go into the wood.

Notice: We recommend that a service center, which has an electric sharpener, perform important sharpening work.

  1. Step 1: Tensioning chain.
  2. Step 2: Sharpen the cutters corner with a 2mm-2.5mm diameter round file.
  3. Step 3: Sharpen the top plate, side plate and depth gauge with a flat file.
  4. Step 4: File all the cutters to the specified angles and the same length.
    • Notice: During the process:
      • Keep the file flat with the surface to be sharpened.
      • Use the midpoint of the file bar.
      • Use light but firm pressure when sharpening the surface.
      • Lift the file away on each return stroke.
      • Sharpen the cutters on one side and then move to the other side.

Replace the chain if:

  • The length of the cutting edges is less than 1/6 in. (5 mm).
  • There is too much space between the drive links and the rivets.
  • The cut speed is slow.
  • Sharpening the chain many times but it does not increase the cutting speed, The chain is worn.

Guide bar maintenance:

Notice: Make sure that it is turned over periodically to keep symmetrical wear on the bar.

  1. Lubricate the bearings on the nose sprocket (if present) with the syringe (not included).
  2. Clean the bar groove with the scraping hook (not included).
  3. Clean the lubrication holes.
  4. Remove burr from the edges and level the cutters with a flat file.

Replace the bar if:

  • The groove does not fit with the height of the drive links (which must never touch the bottom).
  • The inside of the guide bar is worn and makes the chain lean to one side.

Transportation and storage:

  1. Do not store or transport the pole saw attachment when it is running. Always remove the battery pack before storing or transporting.
  2. Always place the guide bar sheath on the guide bar and chain before storing or transporting the pole saw attachment. Use caution to avoid the sharp teeth of the chain.
  3. Clean the pole saw thoroughly before storing. Store the pole saw indoors, in a dry place that is locked and/or inaccessible to children.
  4. Keep away from corrosive agents such as garden chemicals and de-icing salts.

Troubleshooting

ProblemCauseSolution
Motor does not run.
  • The battery pack is not attached to the pole saw.
  • No electrical contact between the saw and battery.
  • The battery pack is depleted.
  • The lock-off button is not depressed before pressing the trigger.
  • The battery pack or power head is too hot.
  • Attach the battery pack to the pole Saw.
  • Remove battery, check contacts and reinstall the battery pack.
  • Charge the battery pack.
  • Press down the lock-off lever and hold it, then depress the trigger to turn on the pole saw.
  • Allow the battery pack or power head to cool until the temperature drops below 152°F (67°C).
  • Release the trigger; remove the battery pack and allow it to cool.
Motor runs, but chain does not Rotate.
  • Saw chain is bound in the wood.
  • Debris in bar groove.
  • Debris in chain-sprocket Cover.
  • Chain does not engage drive Sprocket.
  • Remove saw chain and guide bar from the wood then restart the pole saw.
  • Press the saw chain against the wood, move the pole saw back and forth to discharge the debris.
  • Remove battery pack, then remove chain-sprocket cover and clean out debris.
  • Remove the battery pack and reinstall the chain, making sure that the drive links on the chain are fully seated on the sprocket.
Pole saw does not cut properly.
  • Dull chain.
  • Chain installed backwards.
  • Worn chain.
  • Dry or excessively stretched Chain.
  • Chain not in bar groove.
  • Sharpen the chain cutters, following the section "Sharpen the cutters".
  • Remove the battery pack and reinstall the saw chain, following the section "Replacement and Installation of Chains".
  • Remove the battery pack and replace the chain following the section "Replacement and Installation of Chains".
  • Check the oil level. Refill the oil tank if necessary.
  • Remove the battery pack and reinstall the saw chain, following the section "Replacement and Installation of Chains".
Bar and chain running hot and Smoking.
  • Chain oil tank is empty.
  • Debris in guide bar groove.
  • Filling bar and chain lubricant.
  • Clear the debris in the groove.

Warranty & Support

Supstable Warranty Policy:

Each Supstable tool undergoes a comprehensive examination and testing prior to dispatch. Rest assured, there is a 3-year no-worry warranty from the date of the initial purchase.

If any issues arise during usage, please reach out to Supstable's service center. Supstable will be serviced or replaced at no cost, provided the inspection reveals faults stemming from process or material defects.

Please note that this warranty excludes the following scenarios:

  • Repairs conducted or attempted by unauthorized individuals.
  • Maintenance necessitated by normal wear and tear.
  • The tool has been subjected to abuse, misuse, or improper maintenance.
  • The tool has been altered or modified in any way.

For support, contact: support@supstable.com

User Tips

  • Always ensure the battery is fully charged before starting any task to maximize runtime and performance.
  • Regularly check chain tension and lubrication to ensure smooth operation and prolong the life of the saw.
  • For optimal safety and control, especially when using the pole saw, maintain a stable stance and use both hands.

Frequently Asked Questions

Q: How long is the extendable rod?
A: The telescopic pole extends from 1.8 meters (approximately 6 feet) to 2.9 meters (approximately 9.5 feet).
Q: What is the warranty period for this product?
A: The product comes with a 3-year no-worry warranty from the date of initial purchase.

Disposal

Disposal of the appliance:

This product has been marked with a symbol relating to removing electric and electronic waste. This means that this product shall not be discarded with household waste but that it shall be returned to a collection system. It will then be recycled or dismantled in order to reduce the impact on the environment. Electric and electronic equipment can be hazardous for the environment and for human health since they contain hazardous substances.

Disposal of an exhausted battery pack:

To preserve natural resources, please recycle or dispose of the battery pack properly. This battery pack contains Li-ion batteries. Consult your local waste authority for information regarding available recycling and/or disposal options. Discharge your battery pack Li-ion by operating your tool, then remove the battery pack from the tool housing and cover the battery pack connections with heavy-duty adhesive tape to prevent short circuit and energy discharge. Do not attempt to open or remove any of the components.

Disposal of the packaging:

The packaging consists of cardboard and correspondingly marked plastics that can be recycled. Make these materials available for recycling.

EC Declaration of Conformity

This declaration of conformity is issued under the sole responsibility of the manufacturer.

Manufacturer: Shenzhenshi chunzao kejiyouxian gongsi
Address: 13F, No. 69-2 Fuqian Road, Fumin Community, Fucheng Street, Longhua District, Shenzhen

Product(s): Cordless Pruning Saw
Model: S3 Lite
Brand Name: Supstable

European Representative: Apex CE Specialists GmbH
Address: Grafenberger Allee 277, 40237 Düsseldorf, DE
TEL: +49 21312066043
E-mail: oylily88@gmail.com

UK Representative: APEX CE SPECIALISTS LIMITED
Address: 6f East Union Street, Manchester, England, M16 9AE
TEL: +44 1616371080
E-mail: oylily88@gmail.com

Complies with the essential health and safety requirements of the following Directives:
2006/42/EC Machinery Directive; 2014/30/EU EMC Directive; 2014/35/EU LVD Directive

For the components Battery pack T1840-10 meets the following requirements
2014/30/EU EMC Directive

Standards and technical specifications referred to:
EN 62841-1:2015+AC:2015+A11:2022; EN 62841-4-1:2020
EN 60335-1:2012+AC:2014+A11:2014+A13:2017+A1:2019+A2:2019+A14:2019+A15:2021+A16:2023
EN 60335-2-29:2021+A1:2021; EN 60204-1:2018; EN ISO 12100:2010
EN IEC 55014-1:2021; EN IEC 55014-2:2021
EN IEC 61000-3-2:2019+A1:2021
EN 61000-3-3:2013+A1:2019+A2:2021+A2:2021/AC:2022
EN 60335-2-29:2021 + A1:2021
EN60335-1:2012 + AC:2014 + A11:2014 + A13:22017+A1:2019 + A2:2019 + A14:2019 + A15:2021 + A16:2023
EN 62233:2008

For the components Battery pack T1840-10, we confirm them components comply with regulations of:
EN IEC 55014-1:2021; EN IEC 55014-2:2021
EN IEC 61000-3-2:2019+A1:2021
EN 61000-3-3:2013+A1:2019+A2:2021

Signed for and on behalf of:

Signature: Chao Ma
Position: QA Director
Place and date of issue: Shenzhen, 20 Mar. 2025

Signature: Wells Yan
Position: Manager, APEX CE SPECIALISTS LIMITED
Date of issue: 2025.8.16

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.