ANDELI RSR-1600/2500/3500

Contents

ANDELI RSR Series Portable Capacitor Discharge Stud Welding Machine User Manual

Models: RSR-1600, RSR-2500, RSR-3500

1. Introduction

This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your ANDELI RSR Series Portable Capacitor Discharge Stud Welding Machine. Please read this manual thoroughly before using the machine to ensure proper function and safety.

The ANDELI RSR Series offers three models: RSR-1600, RSR-2500, and RSR-3500, each designed for efficient and reliable stud welding across various materials and stud sizes.

ANDELI RSR-2500 Stud Welding Machine

Figure 1: ANDELI RSR-2500 Stud Welding Machine (representative model)

2. Safety Precautions

Always observe the following safety guidelines to prevent injury or damage to the equipment:

  • Ensure the machine is connected to a properly grounded power source.
  • Wear appropriate personal protective equipment (PPE), including welding helmet, gloves, and protective clothing.
  • Do not operate the machine in wet conditions or near flammable materials.
  • Never weld when the machine is actively charging. The front panel includes a warning: "Note: Do not weld when charging."
  • Ensure adequate ventilation in the work area.
  • Keep children and unauthorized personnel away from the welding area.
  • Disconnect power before performing any maintenance or adjustments.

3. Setup

Follow these steps to set up your stud welding machine:

  1. Unpack and Inspect: Carefully remove the welding machine and all accessories from the packaging. Inspect for any signs of damage during transit. Refer to the image below for typical included accessories.

    ANDELI RSR-3500 Stud Welding Machine and included accessories

    Figure 2: Typical accessories included with the RSR-3500 model.

    Standard accessories typically include:

    • Ground Clamp (x2)
    • Stud Welding Torch
    • Chucks (M3, M4, M5, M6, M8, M10 depending on model)
    • Carbon Steel Screws (e.g., M6*10)
  2. Connect Ground Clamp: Attach the ground clamp securely to the workpiece or a clean, bare metal part of the work table to ensure a good electrical connection.

  3. Connect Stud Welding Torch: Connect the stud welding torch to the designated port on the front panel of the machine.

  4. Power Connection: Plug the machine into a suitable 220V power outlet. Ensure the power switch is in the OFF position before plugging in.

4. Operating Instructions

The ANDELI RSR Series machines are designed for efficient capacitor discharge stud welding. Follow these steps for operation:

  1. Power On: Turn on the main power switch. The digital display on the front panel will illuminate.

  2. Charging: The machine will begin charging its capacitors. The "CHARGE" indicator will be active. Charging time is approximately 4 seconds. Wait for the "READY" indicator to light up before welding.

    Diagram illustrating the fast charging process

    Figure 3: Fast charging process, approximately 4 seconds.

  3. Select Stud and Chuck: Choose the appropriate stud diameter (M3-M10 depending on model) and corresponding chuck for your application. The RSR-1600 supports M3-M6, RSR-2500 supports M3-M8, and RSR-3500 supports M3-M10.

    Illustration of various workpiece types and compatible studs

    Figure 4: Examples of compatible studs and workpieces.

  4. Adjust Voltage: Use the intelligent adjustment knob on the front panel to set the welding voltage. Refer to the "Charging Voltage Reference" table in the Specifications section for recommended settings based on stud diameter. The machine features one-key intelligent voltage adjustment.

  5. Position Stud: Insert the stud into the chuck of the welding torch. Place the stud firmly against the workpiece at the desired welding location.

  6. Weld: Press the trigger on the welding torch. The machine will discharge, welding the stud to the workpiece. A single screw can be welded in approximately 4 seconds.

    Close-up of welded studs on a workpiece

    Figure 5: Example of firmly welded studs.

  7. Dual-Gun Control (if applicable): Some models may support dual-gun control for increased efficiency. This allows for continuous welding without waiting for the machine to recharge between welds.

    Video 1: Demonstration of the stud welding machine, including dual-gun control and various welding applications.

5. Maintenance

Regular maintenance ensures the longevity and optimal performance of your welding machine:

  • Cleaning: Keep the machine clean and free from dust and debris. Use a dry cloth to wipe down the exterior. Ensure no metal particles accumulate around the connections.

  • Ventilation: Ensure the high-speed cooling fans are not obstructed to prevent overheating. The machine is equipped with overtemperature protection.

    Icons representing key functions: high-speed fans, overtemperature protection, DC inverter, power input

    Figure 6: Functional indicators including high-speed fans and overtemperature protection.

  • Cable Inspection: Regularly check all cables and connections for wear, damage, or loose fittings. Replace any damaged components immediately.

  • Storage: Store the machine in a dry, clean environment when not in use.

6. Troubleshooting

If you encounter issues with your welding machine, consider the following common problems and solutions:

  • Machine Not Powering On:

    • Check the power cable connection and ensure it is securely plugged into a live outlet.
    • Verify the main power switch is in the ON position.
    • Check the circuit breaker or fuse for the power outlet.
  • No Weld/Weak Weld:

    • Ensure the ground clamp has a clean, secure connection to the workpiece.
    • Verify the correct stud diameter and chuck are being used.
    • Adjust the welding voltage according to the stud diameter (refer to the Specifications section).
    • Ensure the machine is fully charged and the "READY" indicator is lit before attempting to weld. Remember: Do not weld when charging.
    • Check for proper contact between the stud and the workpiece.
  • Overheating:

    • Ensure the cooling fans are not obstructed and are functioning correctly.
    • Allow the machine to cool down if the overtemperature protection activates.
    • Ensure adequate ventilation in the work area.

For persistent issues, please contact customer support.

7. Specifications

The following table details the technical parameters for the ANDELI RSR Series models:

Technical Parameters and Charging Voltage Reference table

Figure 7: Technical Parameters and Charging Voltage Reference.

Parameter RSR-1600 RSR-2500 RSR-3500
Rated Voltage220V±15%220V±15%220V±15%
Rated Power (VA)375375375
Frequency (Hz)50/6050/6050/60
Charge and Discharge Voltage (V)36-19736-19736-197
Welding RangeM3-M6M3-M8M3-M10
Welding MaterialIron, carbon steel, stainless steel, aluminum, galvanized sheet
Welding Energy (J/W/S)160025005500
Power SupplyElectrolytic capacitor
Capacitance (μF)72000108000141000
Level of ProtectionIP22
Size (mm)490*320*210
Weight (KG)<15.6<17.3<18.6
Welding Speed15-50pcs per minute (depends on output voltage and stud diameter)
Torch Cable LengthStandard 4m
Stud Length RangeStandard up to 35MM (can be extended)
DIY SuppliesElectrical
OriginMainland China
CertificationNONE

Charging Voltage Reference

Stud Diameter Charging Voltage (V) Remark
M355-65Adjust the parameters according to the actual situation
M465-75
M570-85
M685-110
M8130-160
M10160-180

8. User Tips

  • For optimal weld strength and appearance, always ensure the workpiece surface is clean and free of rust, paint, or other contaminants.
  • Experiment with voltage settings on scrap material before working on your final project to find the ideal setting for your specific stud and material combination.
  • Take advantage of the fast 4-second charging time to maintain a steady workflow.
  • If using a dual-gun setup, ensure both guns are properly calibrated and maintained for consistent results.
  • When welding thin sheets (e.g., 0.6mm), the machine is designed to produce a slight indentation on the back with no obvious imprints, ensuring minimal distortion.

9. Warranty and Support

For any questions, technical support, or warranty inquiries regarding your ANDELI RSR Series Stud Welding Machine, please contact the seller directly. You may reach them via:

  • Email: ahe13332502386@163.com
  • WhatsApp: +8618373098865

Please provide your product model and purchase details when contacting support to facilitate a quicker resolution.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.