ANENJI ANJ-5KW-48V-WIFI

Contents

ANENJI 5KW 48V Hybrid Solar Inverter/Charger User Manual

Model: ANJ-5KW-48V-WIFI

Brand: ANENJI

About This Manual

Purpose

This manual describes the assembly, installation, operation, and troubleshooting of this unit. Please read this manual carefully before installations and operations. Keep this manual for future reference.

Scope

This manual provides safety and installation guidelines as well as information on tools and wiring.

Safety Instructions

WARNING: This chapter contains important safety and operating instructions. Read and keep this manual for future reference.

  1. Before using the unit, read all instructions and cautionary markings on the unit, the batteries, and all appropriate sections of this manual.
  2. CAUTION – To reduce risk of injury, charge only deep-cycle lead acid type rechargeable batteries. Other types of batteries may burst, causing personal injury and damage.

  3. Do not disassemble the unit. Take it to a qualified service center when service or repair is required. Incorrect re-assembly may result in a risk of electric shock or fire.
  4. To reduce risk of electric shock, disconnect all wirings before attempting any maintenance or cleaning. Turning off the unit will not reduce this risk.
  5. CAUTION - Only qualified personnel can install this device with battery.

  6. NEVER charge a frozen battery.
  7. For optimum operation of this inverter/charger, please follow required spec to select appropriate cable size. It's very important to correctly operate this inverter/charger.
  8. Be very cautious when working with metal tools on or around batteries. A potential risk exists to drop a tool to spark or short circuit batteries or other electrical parts and could cause an explosion.
  9. Please strictly follow installation procedure when you want to disconnect AC or DC terminals. Please refer to INSTALLATION section of this manual for the details.
  10. Fuse is provided as over-current protection for the battery supply.
  11. GROUNDING INSTRUCTIONS - This inverter/charger should be connected to a permanent grounded wiring system. Be sure to comply with local requirements and regulation to install this inverter.
  12. NEVER cause AC output and DC input short circuited. Do NOT connect to the mains when DC input short circuits.
  13. Warning!! Only qualified service persons are able to service this device. If errors still persist after following troubleshooting table, please send this inverter/charger back to local dealer or service center for maintenance.

Product Overview

The ANENJI 5KW 48V Hybrid Solar Inverter/Charger is a versatile unit designed for solar power systems, offering both on-grid and off-grid capabilities. It features a pure sine wave output, dual AC outputs, and a 100A MPPT solar charge controller. The inverter supports lithium battery activation and includes Wi-Fi for remote monitoring via an app. Its robust design ensures stable and efficient power conversion for various applications.

Key Features

  • Dual output for smart load management
  • Lithium battery activation function by PV or Utility
  • Colored LCD with RGB lights
  • Compatible with LiFePO4 battery via RS485
  • PV input up to 500Vdc Max
  • Built-in MPPT 100A
  • Capable to work without battery
  • Detachable dust cover for harsh environments
  • Built-in Wifi remote monitoring
  • Support multiple output priority: UTL, SOL, SBU, SUB
  • EQ function to optimize battery performance and extend lifecycle
  • Pure sine wave output for stable power
  • Low-noise operation (approx. 45dB)
  • Multiple protection functions: Short-circuit, Surge, Overload, Over-Temp, Low Voltage, High Voltage
ANENJI 5KW 48V Hybrid Solar Inverter with labeled components
Figure 1: Product Overview with Labeled Components
This diagram shows the front and bottom panels of the inverter, highlighting the LCD display, function buttons, RGB indicator, power on/off switch, battery input, AC input, main output, second output, WiFi antenna port, RS485 communication port, grounding, and PV input.
Product Characteristics and Features
Figure 2: Product Characteristics
This image summarizes the key features of the inverter, including pure sine wave, dual outputs, 100A MPPT, colored LCD, PV 60-500Vdc, lithium battery activation, BMS compatibility, capability to work without battery, detachable dust cover, multiple output priority, WiFi remote monitoring, and battery optimization function.
Pure Sine Wave Output Application Examples
Figure 3: Pure Sine Wave Output
Illustrates the inverter providing high-quality AC power to common household appliances such as computers, refrigerators, TVs, and water heaters, emphasizing its stable output and high compatibility.
Inverter Low-Noise Operation
Figure 4: Low-Noise Operation
This image highlights the inverter's noise reduction technology, showing comparative noise levels: Library (15db), Inverter (45db), Voices (60db), Alarm clock (80db), indicating quiet operation.
Multi-Protection Functions
Figure 5: Multi-Protection Functions
This graphic illustrates the multiple protection features of the inverter, including short-circuit protection, surge protection, overload protection, over-temperature protection, low voltage protection, and high voltage protection, ensuring safer and more reliable use.

Setup (Installation)

Unpacking and Inspection

Before installation, please inspect the unit. Ensure that nothing inside the package is damaged. The package should contain:

  • The inverter unit x 1
  • User manual x 1
  • PV connector x 2
  • WiFi antenna x 1

Preparation

Before connecting all wirings, remove the bottom cover by unscrewing the three or two screws as shown in the product overview diagram.

Mounting the Unit

Consider the following points when selecting an installation location:

  • Do not mount the inverter on flammable construction materials.
  • Mount on a solid surface.
  • Install this inverter at eye level for easy LCD display readability.
  • The ambient temperature should be between 0°C and 55°C for optimal operation.
  • The recommended installation position is vertically on the wall.
  • Ensure sufficient heat dissipation and space for wiring by keeping other objects and surfaces clear, as shown in the diagram below.

Note: Suitable for mounting on concrete or other non-combustible surfaces only.

Battery Connection

CAUTION: For safety and regulation compliance, install a separate DC over-current protector or disconnect device between the battery and inverter. Refer to the typical amperage table for required fuse or breaker size.

WARNING: All wiring must be performed by qualified personnel. Use appropriate cable for battery connection to reduce risk of injury.

Follow these steps for battery connection:

  1. Make positive and negative cables based on recommended terminal size.
  2. Connect all battery packs as required by the unit.
  3. Insert battery cable flatly into the battery connector of the inverter and ensure bolts are tightened with a torque of 4~6Nm. Verify correct polarity at both the battery and the inverter/charger.

AC Input/Output Connection

CAUTION: Before connecting to an AC input power source, install a separate AC breaker (recommended 50A) between the inverter and the AC input power source. This ensures the inverter can be securely disconnected during maintenance and protected from overcurrent. Do not mis-connect input and output connectors.

WARNING: All wiring must be performed by qualified personnel. Use appropriate cable for AC input connection. Refer to the suggested cable requirement table for AC wires.

Follow these steps for AC input/output connection:

  1. Before making AC input/output connection, ensure the DC protector or disconnector is open.
  2. Remove 10mm of insulation sleeve for six conductors. Shorten phase L and neutral conductor by 3mm.
  3. Insert AC input wires according to polarities (Ground, L, N) indicated on the terminal block and tighten the terminal screws. Connect the PE protective conductor first.
  4. WARNING: Ensure the AC power source is disconnected before attempting to hardwire it to the unit.

  5. Insert AC output wires according to polarities indicated on the terminal block and tighten terminal screws. Connect the PE protective conductor first.
  6. Ensure all wires are securely connected.

CAUTION: Important: Connect AC wires with correct polarity. Reversed L and N wires can cause utility short-circuiting when inverters operate in parallel.

CAUTION: Appliances like air conditioners require 2-3 minutes to restart. If power shortages occur and recover quickly, it can damage connected appliances. Check if your air conditioner has a time-delay function. The inverter may trigger overload fault to protect appliances, but internal damage can still occur.

PV Connection

CAUTION: Before connecting to PV modules, install a separate DC circuit breaker between the inverter and PV modules.

WARNING: All wiring must be performed by qualified personnel. Use appropriate cable for PV module connection. Refer to the suggested cable requirement table for PV wires.

PV Connection Diagram for a House
Figure 6: PV Connection Diagram
This diagram illustrates a typical solar power system setup, showing the connection of solar panels, inverter, power grid, battery, and generator to a household. It also provides key parameters for PV module selection: Max. PV Array Power 5000W, Max. Solar Charge Current 100A, Max. PV Array Open Circuit Voltage 500VDC.

Follow these steps for PV module connection:

  1. Remove 6mm of insulation sleeve for positive and negative conductors.
  2. Check correct polarity of connection cable from PV modules and PV input connectors. Connect positive (+) to positive (+) and negative (-) to negative (-).
  3. Ensure the wires are securely connected.

Final Assembly

After connecting all wirings, replace the bottom cover by screwing in the two screws.

Video 1: Solar Inverter Wiring Guide
This video demonstrates the wiring process for the ANJ-5KW-48V-WIFI Solar Inverter, including removing the port cover, connecting the main AC output, connecting the battery, reinstalling the port cover, and turning on the inverter.

Operating

Power ON/OFF

Once the unit has been properly installed and the batteries are connected, simply press the On/Off switch (located on the side of the case) to turn on the unit.

Operation and Display Panel

The inverter's front panel features an LCD display, three indicators, and four function keys to show operating status and power information.

RGB Indicator Messages

ModeRGB IndicatorMessages
Inverter modeGreen Solid OnOutput is powered by battery or PV in battery mode. Battery is fully charged or isn't charged.
Green FlashingBattery is charging with 2s-on and 1s-off.
AC modeBlue Solid OnOutput is powered by AC or PV in AC mode. Battery is fully charged or isn't charged.
Blue FlashingBattery is charging with 2s-on and 1s-off.
Standby modeCyan Solid OnBattery is fully charged or isn't charged.
Cyan FlashingBattery is charging with 2s-on and 1s-off.
Fault modeRed Solid OnFault occurs in the inverter.
Bypass modePurple Solid OnWorking in AC mode without charging.
Charging modeYellow Solid OnBattery is fully charged, when switch is off.
Yellow FlashingBattery is charging, when switch is off.

Function Keys

Function KeyDescription
ESCTo exit setting mode
UPTo go to previous selection
DOWNTo go to next selection
ENTERTo confirm the selection in setting mode or enter setting mode

LCD Display Description

The LCD display information can be switched by pressing keys. Information is shown in five areas:

  • Area 1: PV data (voltage, current, power).
  • Area 2: Battery data (voltage, current, power, SOC).
  • Area 3: AC output data (voltage, current, power, percentage, frequency).
  • Area 4: AC input data (voltage, current, power, percentage, frequency).
  • Area 5: Setting program code, Eco/buzzer/error/warning.

LCD Data Polling Display Mode

  • Simultaneously polling data: Press "UP" or "DOWN" to show all data from area 1 to area 4 simultaneously. All data updates with pressing. Press ESC to return to initial data.
  • Independent polling data: Data of areas 1-4 can be polled independently:
    1. Press "Enter", circle icon of area 1 flashes. Use "UP" or "DOWN" to display data of area 1.
    2. Continue pressing "Enter", circle icon of area 2 flashes. Use "UP" or "DOWN" to display data of area 2.
    3. Continue pressing "Enter", circle icon of area 3 flashes. Use "UP" or "DOWN" to display data of area 3.
    4. Continue pressing "Enter", circle icon of area 4 flashes. Use "UP" or "DOWN" to display data of area 4.
    5. Continue pressing "Enter", circle icon of area 1 flashes, returning to the beginning.

LCD Setting

Press and hold the "Enter" key for 3 seconds to enter setting mode. Use "UP" or "DOWN" to select programs, then "ENTER" to confirm or "ESC" to exit. The LCD will show the setting program code, minimum/maximum values, program item, and current settable value.

For detailed setting programs, refer to the comprehensive tables in the full user manual (PDF) available at User Manual (PDF).

Battery Equalization

The equalization function reverses the buildup of negative chemical effects like stratification and removes sulfate crystals, extending battery life. To apply equalization:

  1. Enable battery equalization in monitoring LCD setting program 33.
  2. Set equalization interval in program 37, or activate immediately in program 39.

The controller enters Equalize stage when the set interval is reached or immediately activated. It charges the battery until it reaches the equalization voltage, then maintains it at that voltage until the set equalized time is reached. If the voltage doesn't rise sufficiently, the equalized time may be extended. If still low after timeout, equalization stops, and the system returns to float stage.

Setting for Lithium Battery

If using a lithium battery, ensure it's a configured type. Two connectors are on the lithium battery: RS485 port of BMS and power cable.

Follow these steps for lithium battery connection:

  1. Assemble battery terminals based on recommended cable and terminal size (same as Lead acid).
  2. Connect the RS485 port of the battery to the BMS (RS485) communication port of the inverter.

The communication cable delivers information and signals between the lithium battery and the inverter, allowing for re-configuration of charging voltage, charging current, and battery discharge cut-off voltage according to lithium battery parameters. The inverter can start or stop charging based on the lithium battery status.

For PYLON US2000 lithium battery setting:

  • Dip Switch: 4 Dip Switches set baud rate and battery group address. 'ON' is '1', 'OFF' is '0'. Dip 1 'ON' for baud rate 9600. Dips 2, 3, 4 are for battery group address.
  • Installation Process:
    1. Use the RS485 cable to connect the inverter and Lithium battery.
    2. Switch on the Lithium battery.
    3. Press for more than three seconds to start the Lithium battery; power output ready.
    4. Turn on the inverter.
    5. Select battery type as "Li2" in LCD program 5.

If communication is successful, the battery icon 'LI' on the LCD display will light up.

For lithium battery without communication, refer to the full user manual (PDF) for detailed settings to avoid BMS protection.

Maintenance

Regular maintenance is crucial for the longevity and optimal performance of your ANENJI Hybrid Solar Inverter. Always ensure the unit is powered off and all wirings are disconnected before attempting any maintenance or cleaning to prevent electric shock.

  • Cleaning: Keep the inverter's exterior clean and free from dust. The detachable dust cover can be removed for cleaning.
  • Ventilation: Ensure that the inverter's ventilation openings are clear and not blocked to allow for proper heat dissipation.
  • Wiring Inspection: Periodically check all wiring connections (battery, AC input/output, PV input) for tightness and signs of wear or damage. Ensure no anti-oxidant substance is applied to terminals before tightening.
  • Battery Health: Monitor battery voltage and performance. If using lead-acid batteries, consider using the battery equalization function periodically to prevent sulfation.
  • Firmware Updates: Check the manufacturer's website or app for any available firmware updates for the inverter or Wi-Fi module to ensure optimal performance and compatibility.

WARNING: Only qualified service personnel should perform complex maintenance or repairs. Do not attempt to disassemble the unit yourself.

Troubleshooting

This section provides guidance for common issues. If problems persist, contact a qualified service person.

Fault Reference Code

Fault CodeFault Event
01Over temperature of inverter module
02Over temperature of DCDC module
03Battery voltage is too high
04Over temperature of PV module
05Output short circuited.
06Output voltage is too high.
07Overload time out
08Bus voltage is too high
09Bus soft start failed
10PV over current
11PV over voltage
12DCDC over current
13Over current or surge
14Bus voltage is too low
15Inverter failed (Self-checking)
18Op current offset is too high
19Inverter current offset is too high
20DC/DC current offset is too high
21PV current offset is too high
22Output voltage is too low
23Inverter negative power
24Op2 current offset is too high

Warning Indicator

Warning CodeWarning EventAudible Alarm
02Temperature is too HighBeep three times every second
04Low batteryBeep once every second
07OverloadBeep once every 0.5 second
10Output power deratingBeep twice every 3 seconds
14Fan blockedNone
15PV energy is lowBeep twice every 3 seconds
19Lithium Battery communication is failedBeep once every 0.5 second
21Lithium Battery over currentNone
22The load exceeds the set value of program 47None
E9Battery equalizationNone
bPBattery is not connectedNone

General Troubleshooting

ProblemLCD/LED/BuzzerExplanation / Possible causeWhat to do
Unit shuts Down automatically during startup process.LCD/LEDs and buzzer will be active for 3 seconds and then complete off.The battery voltage is too low1. Re-charge battery.
2. Replace battery.
No response after power on.No indication.1. The battery voltage is far too low.
2. Battery polarity is connected reversed.
1. Check if batteries and the wiring are connected well.
2. Re-charge battery.
3. Replace battery.
Input voltage is displayed as 0 on the LCD and green LED is flashing.Input protector is trippedCheck if AC breaker is tripped and AC wiring is connected well.
Mains exist but the unit works in battery mode.Green LED is flashing.Insufficient quality of AC power. (Shore or Generator)Check if AC wires are too thin and/or too long.
Check if generator (if applied) is working well or if input voltage range setting is correct. (UPS / Appliance)
Green LED is flashing.Set "Solar First" as the priority of output source.Change output source priority to Utility first.
When the unit is turned on, internal relay is switched on and off repeatedly.LCD display and LEDs are flashingBattery is disconnected.Check if battery wires are connected well.
Fault code 07Overload error. The inverter is overload 110% and time is up.Reduce the connected load by switching off some equipment.
Fault code 05Output short circuited.Check if wiring is connected well and remove abnormal load.
Fault code 02Internal temperature of inverter component is over 100°C.Check whether the air flow of the unit is blocked or whether the ambient temperature is too high.
Buzzer beeps continuously and red LED is on.Fault code 03Battery is over-charged.Return to repair center.
The battery voltage is too high.Check if spec and quantity of batteries are meet requirements.
Fault code 06/22Output abnormal (Inverter voltage below than 190Vac or is higher than 260Vac)1. Reduce the connected load.
2. Return to repair center
Fault code 08/09/15Internal components failed.Return to repair center.
Fault code 13Over current or surge.Restart the unit, if the error happens again, please return to repair center.
Fault code 14Bus voltage is too low.If the wires is connected well, please return to repair center.
Another fault codeIf the wires is connected well, please return to repair center.

Specifications

Table 1 Line Mode Specifications

INVERTER MODEL4.2KVA5.0KVA
Input Voltage WaveformSinusoidal (utility or generator)
Nominal Input Voltage230Vac
Low Loss Voltage170Vac±7V (UPS)
90Vac±7V (Appliances)
Low Loss Return Voltage180Vac±7V (UPS);
100Vac±7V (Appliances)
High Loss Voltage280Vac±7V
High Loss Return Voltage270Vac±7V
Max AC Input Voltage300Vac
Nominal Input Frequency50Hz / 60Hz (Auto detection)
Low Loss Frequency40±1Hz
Low Loss Return Frequency42±1Hz
High Loss Frequency65±1Hz
High Loss Return Frequency63±1Hz
Output Short Circuit ProtectionBattery mode: Electronic Circuits
Efficiency (Line Mode)>95% (Rated R load, battery full charged)
Transfer Time10ms typical (UPS); 20ms typical (Appliances)
Output power derating: When AC input voltage drops to 95V or 170V depending on models, the output power will be derated.Output Power
Rated Power 50% Power
90V 170V 280V Input Voltage

Table 2 Inverter Mode Specifications

INVERTER MODEL4.2KVA5.0KVA
Rated Output Power4.2KVA / 4.2KW5.0KVA / 5.0KW
Dual output functionYesYes
Max. main output power4.2KVA / 4.2KW5.0KVA / 5.0KW
Output Voltage WaveformPure Sine Wave
Output Voltage Regulation230Vac±5%
Output Frequency50Hz or 60Hz
Peak Efficiency94%
Surge Capacity2* rated power for 5 seconds
Nominal DC Input Voltage24Vdc48Vdc
Cold Start Voltage23.0Vdc46.0Vdc
Low DC Warning Voltage (Just for AGM and Flooded)@ load < 20%: 22.0Vdc
@ 20% ≤ load < 50%: 21.4Vdc
@ load ≥ 50%: 20.2Vdc
@ load < 20%: 44.0Vdc
@ 20% ≤ load < 50%: 42.8Vdc
@ load ≥ 50%: 40.4Vdc
Low DC Warning Return Voltage (Just for AGM and Flooded)@ load < 20%: 23.0Vdc
@ 20% ≤ load < 50%: 22.4Vdc
@ load ≥ 50%: 21.2Vdc
@ load < 20%: 46.0Vdc
@ 20% ≤ load < 50%: 44.8Vdc
@ load ≥ 50%: 42.4Vdc
Low DC Cut-off Voltage (Just for AGM and Flooded)@ load < 20%: 21.0Vdc
@ 20% ≤ load < 50%: 20.4Vdc
@ load ≥ 50%: 19.2Vdc
@ load < 20%: 42.0Vdc
@ 20% ≤ load < 50%: 40.8Vdc
@ load ≥ 50%: 38.4Vdc

Table 3 Charge Mode Specifications

Utility Charging Mode4.2KVA5.0KVA
Max Charging Current (PV+AC) (@ VI/P=230Vac)100Amp100Amp
Max Charging Current (AC) (@ VI/P=230Vac)80Amp60Amp
Bulk Charging Voltage (Flooded Battery)29.2Vdc58.4Vdc
Bulk Charging Voltage (AGM / Gel Battery)28.2Vdc56.4Vdc
Floating Charging Voltage27Vdc54Vdc
Overcharge Protection32Vdc63Vdc
Battery reverse connection protectionNoNo
Charging Algorithm3-Step
Charging CurveGraph showing Battery Voltage per cell and Charging Current over time, with Bulk, Absorption, and Maintenance phases.

Solar Input Specifications

INVERTER MODEL4.2KVA5.0KVA
Rated Power5000W5000W
Max. PV Array Open Circuit Voltage500Vdc
PV Array MPPT Voltage Range60Vdc~500Vdc
Max. Input Current27A27A
Max. Charging Current (PV)100A100A

Table 4 General Specifications

INVERTER MODEL4.2KVA5.0KVA
Operating Temperature Range-10°C to 55°C
Storage temperature-15°C~60°C
Humidity5% to 95% Relative Humidity (Non-condensing)
Dimension (D*W*H), mm368x312x105
Net Weight, kg6.79.3

Wi-Fi Plug Pro Quick Installation Guideline

1. Install the Wireless Antenna

Refer to the product overview diagram for the location of the WiFi antenna port. Screw in the provided WiFi antenna securely.

2. Download the SmartESS App

  1. Scan the QR code provided in the manual or product packaging to download the SmartESS App (available on iPhone App Store and Android).
  2. Open the App, click "Registration", and select "Mobile phone Registration" or "Email Registration".
  3. Turn on Bluetooth or WiFi on your mobile device as needed.

3. Bluetooth Connection to the Digital Collector

  1. Click the "Toolbox" in the app and select "BLE network" or "Wi-Fi network".
  2. If choosing Bluetooth distribution network, the app will automatically scan for nearby devices. On the "Bluetooth Pairing" page, find the PN corresponding to your digital collector and click "Connect".

4. Add Datalogger

  1. Log in to your account and click the "Datalogger" button. Tap the "+" button on the top-right corner of the datalogger page.
  2. Follow the prompts to type in the necessary information to add the datalogger. The PN number is located next to the machine appliance label. (Initial Password: 12345678)

5. Networking Settings

  1. Select the corresponding 2.4G WiFi network according to the prompts, fill in the password, and click "Start".
  2. The app will display "Connecting to the Network" and then confirm successful network configuration.

For detailed screenshots and step-by-step visual guidance, please refer to the full user manual (PDF) available at User Manual (PDF).

User Tips

  • Optimal Performance: Ensure proper ventilation around the inverter to prevent overheating, which can impact efficiency and lifespan.
  • Battery Compatibility: When using lithium batteries, always verify compatibility and ensure correct communication settings (RS485) are configured for optimal performance and protection.
  • Wiring Safety: Double-check all wiring connections for tightness and correct polarity during installation to avoid electrical hazards and ensure stable operation.
  • Monitoring: Utilize the Wi-Fi app for remote monitoring of your system's performance, battery status, and any alerts, allowing for proactive management.
  • Load Management: Be mindful of the inverter's maximum output power and avoid overloading to prevent system shutdowns or damage.

Warranty and Support

For warranty information, technical support, or service inquiries, please contact your authorized dealer or the manufacturer directly. Keep your purchase receipt and product model number handy for faster service.

You can also refer to the complete user manual for more detailed information and diagrams: User Manual (PDF).


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.