1. Introduction
This manual provides essential information for the safe and efficient operation, setup, and maintenance of your COOSPO T10 Smart Bike Trainer. Please read this manual thoroughly before use and keep it for future reference.
The COOSPO T10 is a smart bike trainer designed for indoor cycling, featuring a built-in power meter, Bluetooth 5.0, and ANT+ connectivity. It offers up to 15% simulated climb and a maximum power output of 2200W, making it suitable for beginner to intermediate riders.
2. Safety Information
Adhering to safety guidelines is crucial for preventing injury and damage to the equipment. Please observe the following:
- Install and use the trainer on a flat and solid surface.
- Ensure quick release or thru-axle levers are securely locked to the bike frame before each use.
- Do not touch moving parts of the trainer or the hot flywheel after prolonged use.
- Keep children and pets away from the trainer during operation.
- Keep the trainer away from fire, water, and other obstacles.
- Avoid standing or pedaling violently on the trainer.
- Consult a doctor before starting any new exercise program.
- Do not allow individuals unable to take responsibility for their actions to use the trainer.
The manufacturer is not liable for any personal injury or property damage caused by improper use.
3. Package Contents
Before proceeding with setup, please verify that all components are present:
| Item | Quantity |
|---|---|
| Main unit | 1 |
| Support legs | 2 |
| Leg screws (with washers) | 4 |
| Cassette gasket | 4 |
| 5mm hexagonal wrench | 1 |
| 3mm hexagonal wrench | 1 |
| 17mm wrench | 1 |
| Thru-axle adapter - right (pre-installed) | 1 |
| Thru-axle adapter - left | 1 |
| Quick release adapter - right | 1 |
| Quick release adapter - left | 1 |
| 8-9-10 speed cassette conversion spacer | 1 |
| Hydraulic disc brake protection plate | 1 |
| Power adapter | 1 |
4. Setup Guide
4.1 Quick Installation (Unpacking)
- Open the box, remove the main unit and accessories. Place the support legs flat on the ground.
- Align the openings at both ends of the main unit base with the screw holes in the middle of the support legs. Screw in the four support leg screws and tighten them.
- Install the support legs: Align the holes at both ends of the main unit base with the screw holes in the middle of the support legs. After confirming correct positioning, screw in the support leg bolts and ensure the installation is firm.
Note: When installing the level feet, the left one is shorter and the right one (on the flywheel side) is longer.

Image description: A diagram showing the main unit of the COOSPO T10 Smart Bike Trainer with its two support legs attached at the base using screws.
4.2 Bike Cassette Installation
Cassette Not Included.
4.2.1 Shimano Brand Standard Cassette Installation
- 11/12 speed cassette: Mounts directly to the standard free-hub body (no spacer needed).
- 8/9/10 speed cassette: Install the cassette spacer first, then install the cassette onto the free-hub. The cassette spacer should be installed with the notch facing outward.

Image description: A close-up view of the trainer's freehub with text indicating compatibility for Shimano 8-12 speed cassettes. It also shows a cassette spacer with an arrow pointing outwards for proper installation.
4.2.2 SRAM XDR Cassette Installation
Compatible with SRAM 8-11 speed cassettes and SRAM XDR 12 speed cassettes (XDR free-hub body needs to be purchased separately). Replace the standard free-hub body before installing the cassette.

Image description: A diagram showing the installation of an XDR free-hub and a SRAM 12-speed cassette onto the trainer. Installation tips advise pushing the cassette onto the free-hub body and using a tool if the last section doesn't push in easily.
4.3 Bike Frame Installation
Before installing, confirm if your bike uses a thru-axle or quick-release structure. Use the appropriate adapter.
4.3.1 Thru-Axle Frame Installation (142-148mm)
The driven-side thru-axle adapter is pre-installed. You only need to install the thru-axle adapter on the left non-drive side.

Image description: A diagram illustrating the installation of thru-axle adapters for 142mm and 148mm frames. It shows the short head outside for 142mm and the long head outside for 148mm, with the right-side adapter pre-installed.
4.3.2 Quick Release Axle Frame Installation (130-135mm)
If you have a quick-release frame, unscrew the pre-installed thru-axle adapter and replace it with a drive-side quick-release adapter. Use a 17mm wrench to install the quick-release adapter (right).

Image description: A diagram showing the installation of quick-release adapters for 130mm and 135mm frames. It indicates the short head outside for 130mm and the long head outside for 135mm, and reminds to install an additional adapter if present.
4.3.3 Final Bike Mounting Steps
- Adjust the rear derailleur to shift the chain onto the smallest cassette cog, then remove the rear wheel from the bicycle.
- Adjust the bike derailleur to set the cassette to the smallest gear. When installing, make sure the chain is placed on the smallest cassette gear.
- Use the original quick-release lever to lock the frame and the trainer. After installation, shake the frame to confirm that it is securely locked onto the trainer.
Warning: Tighten the quick-release lever/thru-axle and shake the frame to ensure it does not detach from the bike. Improperly tightening may result in property damage and personal injury. Never adjust the quick-release lever/thru-axle while someone is sitting or standing on the bike.
If your bike has a disc brake system, use the provided disc brake caliper protector after removing the rear wheel to prevent caliper failure. If the standard protector is not compatible, prepare your own.
5. Operating Instructions
5.1 Power Adapter Connection
Use the provided power adapter to supply power to the device. The AC cable part can be replaced independently.
Warning: It is prohibited to use non-original power adapters. Damage to the circuit board caused by non-original adapters will not be covered by warranty.

Image description: A diagram showing the connection of the power adapter to the COOSPO T10 Smart Bike Trainer, indicating the AC power cord and the power adapter unit.
5.2 Trainer Working Mode (Power Mode)
The bike trainer must be powered on during operation. It generates resistance and transmits signal data only when connected to a power source. After use, disconnect the power supply. Do not leave it plugged in for extended periods when not in use.
5.3 Signal Indicator Light Mode
The signal indicator light is located at the bottom of the trainer.
- Trainer powered on and stationary:
- Light flashes: Trainer not connected to the mobile app.
- Light stays on continuously: Trainer connected to the mobile app.
- During riding: Light flashes, with frequency increasing as power output rises.

Image description: A diagram highlighting the location of the signal indicator light at the bottom of the COOSPO T10 Smart Bike Trainer.
5.4 Recommended Cycling Software
The COOSPO T10 is compatible with popular virtual cycling platforms via Bluetooth and ANT+.
- Zwift
- Rouvy
- MyWhoosh
- TrainerRoad
- Onelap
- Qidou
- Weride
- And other smart cycling software that support standard protocols.

Image description: The COOSPO T10 Smart Bike Trainer shown alongside various devices (laptop, tablet, smartphone) running popular training apps like Zwift, Rouvy, MyWhoosh, and TrainerRoad, highlighting its Bluetooth and ANT+ compatibility.
Video description: An official product video demonstrating the COOSPO T10 Smart Bike Trainer in use, highlighting its easy setup, stability, and compatibility with popular training apps. It shows a cyclist mounting the bike, riding, and interacting with virtual cycling environments.
6. Maintenance
6.1 Calibration
The T10 trainer is spin-down calibrated at the factory. Recalibration is not needed for a short period. It is recommended to perform a spin-down calibration via "COOSPOTools" app after every 300 riding hours or 6,000 kilometers.
Download "COOSPOTools" from the official website or app store for firmware updates and calibration.
6.2 Cleaning and Storage
- Wipe the trainer with a soft, damp cloth after each use to remove sweat and dust.
- Do not use abrasive cleaners or solvents.
- Store the trainer in a dry, cool place away from direct sunlight and extreme temperatures.
- Ensure the trainer is unplugged when not in use for extended periods.
7. Troubleshooting
7.1 Signal Connection Problems
If your phone or computer cannot detect the trainer's signal, consider the following:
- Ensure the trainer is connected to a power source.
- Verify Bluetooth and Location services are enabled on your phone.
- Search for the trainer within your cycling app, not through your phone's Bluetooth settings.
- Check the trainer's signal light:
- Flashing: Waiting to connect (detectable).
- Steady: Already connected to an app (not detectable by other apps). Close other apps until the light flashes.
- Close other cycling apps or Smart Trainer firmware update apps that might be connected.
- If installing the cycling app for the first time, ensure all permissions are granted. If not, delete and reinstall the app.
- Turn off the trainer, wait 2 minutes, then turn it on again.
- Restart your phone/computer.
- If using an old computer with outdated Bluetooth, try connecting via a phone app instead.
Note: Only one cycling software or bike computer can connect to the trainer at a time. Avoid using a bike computer with training control functions simultaneously with a phone/computer app to prevent abnormal resistance changes.
7.2 Excessive Chain Noise
Excessive chain noise may indicate a mismatch between the bike chain and cassette teeth. This can be due to a difference in distance between the trainer's cassette to the rear fork and the original wheel's cassette to the rear fork.
Solutions:
- Fine-tune the rear derailleur.
- Adjust spacers on the freehub body:
- If trainer cassette distance (A) < original wheel cassette distance (B): Use cassette washers (each adds 0.5mm) to increase distance A.
- If trainer cassette distance (A) > original wheel cassette distance (B): Contact customer service for assistance.

Image description: A diagram illustrating how to use cassette gaskets to adjust the spacing between the cassette and the trainer to reduce chain noise, showing the measurement points A and B.
8. Specifications
| Feature | Detail |
|---|---|
| Model Name | T10 |
| Product Type | Smart Trainer |
| Structural Materials | Steel |
| Packaging Size | 64.7 x 62.7 x 22.5 cm |
| Product Net Weight | 14 kg |
| Power Input | 100V-240V |
| Maximum Power | 2200W |
| Power Meter Accuracy | ±2% |
| Power Calibration | Calibration by APP |
| Simulated Slope | 15% |
| Damping Type | Electromagnetic damping |
| Wireless Signal | BLE 5.0 and ANT+ |
| Data Protocol | Power, cadence, speed |
| Supported Frame Types | 5*130/5*135 (quick release), 12*142/12*148 (thru-axle) |
| Driver Type | Chain Wheel Drive |
| Applicable Flywheel | Shimano 8-12 speed cassette, SRAM 8-11 speed cassette, SRAM XDR 12 speed cassette (requires separate XDR freehub) |

Image description: A diagram showing the dimensions of the COOSPO T10 Smart Bike Trainer, including its length, width, and height.
9. User Tips
- The trainer offers super fast Bluetooth and ANT+ connectivity, ensuring a seamless experience with apps like Zwift and Rouvy.
- Connecting to a PC or MacBook is very easy, and it's fully compatible with MyWhoosh.
- For optimal performance and to avoid signal interference, ensure only one cycling app or device is connected to the trainer at a time.
10. Warranty and Support
10.1 Warranty Terms
- The product warranty period is 1 year from the order placement date. Free repair and parts replacement are provided for non-human-induced hardware or software faults during this period.
- Shipping costs for after-sales repair are borne by the user. Use original packaging materials for return shipments.
- The warranty does not cover:
- Damage from failure to use or install according to the manual.
- Damage caused by human factors or accidents.
- Products disassembled or repaired without company confirmation.
- Malfunctions due to water ingress.
- Aging, scratches, and scuffs from normal use.
- Repair services are available after the warranty period, with corresponding fees charged.
10.2 After-Sales Technical Support
For product information and FAQ, visit the official website: www.coospo.com.
For instructional videos, visit the YouTube channel: @Coospo.
For further questions, contact via email: info@coospo.com or Instagram/Facebook: @coospofitnessofficial / @coospo.