INVT CHF100A-004G/CHF100A-5R5P-4

Contents

INVT CHF100A Series Vector Universal Inverter Instruction Manual

Model: CHF100A-004G/CHF100A-5R5P-4

1. Introduction

This manual provides essential information for the safe and efficient operation of the INVT CHF100A series vector universal inverter. The CHF100A series is designed for adapting motors with 380V, 4KW heavy load, or 5.5KW light load, utilizing a DSP control system for advanced motor control.

It is primarily used in applications such as wind turbines and pump loads, where high speed control accuracy, torque response speed, and low frequency output are critical.

2. Safety Information

WARNING: Failure to follow these safety instructions may result in injury or electric shock.

  • Always wait at least 10 minutes after disconnecting power until the DC bus capacitors fully discharge before performing any work on the inverter.
  • Ensure all safety precautions are followed during installation, operation, and maintenance.
  • Read the entire manual thoroughly before attempting installation or operation.
  • Use proper grounding techniques for the inverter and associated equipment.
Front view of the INVT CHF100A inverter showing the control panel and a warning label.
Front view of the INVT CHF100A inverter, highlighting the control panel and important safety warnings.

3. Installation

Proper installation is crucial for the inverter's performance and safety. This section outlines general guidelines. Refer to the full product manual for detailed wiring diagrams and specific installation steps.

3.1 Environmental Requirements

  • Install in a clean, dry, and well-ventilated area.
  • Avoid direct sunlight, corrosive gases, and excessive dust.
  • Ensure ambient temperature is within the specified operating range.

3.2 Mounting

  • Mount the inverter vertically on a sturdy, non-flammable surface.
  • Allow sufficient clearance around the unit for proper heat dissipation.

3.3 Wiring

  • All wiring must comply with local and national electrical codes.
  • Ensure correct power phase number and supply voltage (380V for this model).
  • Connect the motor according to the specified heavy load (4KW) or light load (5.5KW) configuration.
  • Implement proper grounding for the inverter chassis and motor.
  • Utilize the freely programmable input and output terminals as required for your application.

4. Operation

The CHF100A inverter offers flexible control options to suit various motor applications.

4.1 Control Modes

The inverter supports three primary control modes:

  • No PG Vector Control (SVC): Provides high-performance speed sensorless vector control, effectively suppressing low-frequency shock and swing. Offers a starting torque of 0.5Hz/150%.
  • V/F Control: Standard voltage/frequency control, suitable for general-purpose applications.
  • Torque Control: For applications requiring precise torque management.

The desired control mode can be selected and configured via the inverter's parameters.

4.2 Frequency Setting

Multiple methods are available for setting the operating frequency:

  • Digital setting via the control panel.
  • Analog setting using external voltage or current signals.
  • PID setting for process control applications.
  • Communication setting via serial communication protocols.

4.3 Advanced Functions

  • Simple PLC: The inverter includes 16 simple PLC functions for basic automation tasks.
  • Multi-speed Control: Configure multiple preset speeds for various operational requirements.
  • PID Control: Integrated PID controller for closed-loop process control.
  • DC Braking: Supports both start and stop DC braking for controlled deceleration.
  • Jump Frequency Control: Helps avoid mechanical resonance in the system, enhancing stability and reliability.
  • Instantaneous Power Failure and Non-stop Function: Designed to maintain operation or recover smoothly during brief power interruptions.

5. Maintenance

Regular maintenance ensures the longevity and reliable operation of your INVT CHF100A inverter.

  • Regular Inspection: Periodically check for dust accumulation, loose connections, and signs of overheating or damage.
  • Cleaning: Keep the inverter's ventilation openings clear of obstructions. Use compressed air to remove dust from cooling fins and internal components.
  • Capacitor Discharge: Always observe the 10-minute waiting period for DC bus capacitor discharge after power-off before performing any maintenance or inspection.
  • Environmental Control: Ensure the operating environment remains within specified temperature and humidity limits.

6. Troubleshooting

This section provides general troubleshooting tips. For detailed error codes and solutions, please refer to the comprehensive user manual provided by the manufacturer.

  • No Power: Check input power supply, fuses, and circuit breakers.
  • Motor Not Running: Verify motor connections, control signal inputs, and ensure the inverter is enabled. Check for any fault codes displayed on the control panel.
  • Overcurrent/Overload Fault: Inspect motor load, check for mechanical binding, and verify motor parameters are correctly set in the inverter.
  • Overvoltage/Undervoltage Fault: Check input voltage stability. For overvoltage, consider adding a braking resistor if not already installed and if the application requires rapid deceleration.

7. Specifications

FeatureSpecification
BrandINVT
ModelCHF100A-004G/CHF100A-5R5P-4
Input Voltage380V (Typically 3-phase for industrial inverters)
Adapted Motor (Heavy Load)4KW
Adapted Motor (Light Load)5.5KW
Control ModesV/F open loop, Vector control (SVC), Torque control
Starting Torque (SVC)0.5Hz/150%
Power Range1.5kW to 3MW (General series range; specific to this model is 4KW/5.5KW)
Built-in DC ReactorYes (for 18.5KW~90KW models; check specific model for confirmation)
Built-in Braking UnitYes (for 1.5~15KW models; check specific model for confirmation)
Programmable Logic Control16 simple PLC functions
Frequency Setting ModesDigital, Analog, PID, Communication
Frame MaterialPlastic
OriginMainland China

8. User Tips

Based on general user feedback for similar industrial inverters:

  • Parameter Backup: Before making significant changes to parameters, always back up your current settings. This can save considerable time during troubleshooting.
  • Motor Tuning: For optimal performance, especially with vector control, perform the auto-tuning function for your specific motor if available.
  • Cooling: Ensure adequate airflow around the inverter. Overheating is a common cause of faults and reduced lifespan.
  • Grounding: Double-check all grounding connections. Proper grounding is critical for both safety and noise reduction.

9. Warranty and Support

For specific warranty terms, technical support, or service inquiries, please contact the seller or the official INVT customer service directly. Keep your purchase records handy when contacting support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.