iScooter Y16

Contents

IScooter Y16 Electric Scooter User Manual

Model: Y16

1. Introduction

This user manual provides essential information for the safe and efficient operation of your IScooter Y16 Electric Scooter. Please read this manual carefully before use and retain it for future reference. Illustrations and functions may vary due to product enhancements.

For a complete PDF version of this manual, please refer to the official document: User Manual (PDF).

2. Package Contents

Ensure all items are present and in good condition. If any items are missing or damaged, please contact customer support.

  • Scooter (Main Unit)
  • NFC Key Cards (2 pcs)
  • Mirrors (2 pcs)
  • Front Wheel & Axle & Drum Brake
  • Left Shock Absorber & Trims
  • Front Basket & Mounting Kit
  • Saddle
  • Passenger Seat
  • Front Fender
  • Rear Fender
  • Rear Reflector
  • Drop Stand
  • Tools
  • Charger
  • User Manual & Safety Instructions (this document)
Diagram of all package contents for the Y16 Electric Scooter
Figure 2.1: All components included in the package.

3. Product Overview

Familiarize yourself with the different parts of your IScooter Y16 Electric Scooter.

Labeled diagram of the IScooter Y16 Electric Scooter components
Figure 3.1: Overview of the IScooter Y16 Electric Scooter components.
  1. Saddle
  2. Passenger Seat
  3. Taillight
  4. Rear Fender
  5. Rear Reflector
  6. Shock Absorbers
  7. Drop Stand
  8. Footrests
  9. Battery Disconnect Switch
  10. Charging Port
  11. Mirrors
  12. Brake Levers
  13. Display
  14. Front Basket
  15. Suspension Fork
  16. Front Fender

4. Assembly

Please follow these steps carefully to assemble your electric scooter. It is recommended to watch the assembly video for visual guidance if available. Some users have found assembly challenging, so patience is key.

4.1. Install the Handlebar

Insert the handlebar post fully into the steerer tube, adjust the handlebar so that it is parallel to the fork crown, and tighten the stem expander bolt securely.

Diagram showing handlebar installation steps
Figure 4.1: Handlebar assembly. Ensure the handlebar is parallel to the fork crown and the expander bolt is tightened.

4.2. Install the Display

Align the mounting holes of the display, then tighten the screws securely.

Diagram showing display installation steps
Figure 4.2: Display installation. Secure the display by aligning holes and tightening screws.

4.3. Install the Mirrors

Remove the plastic plugs from the mirror mounting holes. Rotate the mirror stems into their mounts to the desired angle, tighten the lock nuts, and slide down the rubber covers to cover the lock nuts.

Diagram showing mirror installation steps
Figure 4.3: Mirror installation. Adjust angle, tighten lock nuts, and cover with rubber.

4.4. Install the Front Wheel

Attach the drum brake assembly to the front wheel snugly and place the front wheel between the fork legs. Ensure the pin on the inside of the left fork leg fully goes into the slot on the outside of the drum brake backing plate.

Remove the nut and bushing from the front wheel axle. Pass the axle rod through the dropout of the left fork leg, bushing, wheel hub, and the dropout of the right fork leg, ensuring the flange on the axle is fully seated into the hole on the left fork leg. Then tighten the nut securely.

Diagram showing front wheel and drum brake assembly
Figure 4.4: Front wheel assembly. Secure the drum brake and axle, ensuring proper pin alignment.

4.5. Install the Front Fender

Place the front fender between the fork legs and adjust so that the fork legs seat into the fender grooves. Slide the fender down the fork legs to align the mounting holes, then tighten the bolts securely.

Diagram showing front fender installation
Figure 4.5: Front fender installation. Align and secure with bolts.

4.6. Install the Shock Absorbers

Remove the front basket's bottom mounting plate from the rear left side of the frame. Install the left shock absorber with its damper body/cylinder in the same position as the right shock absorber. Then tighten the lower bolt and nut of the right shock absorber. Install the shock absorber trim on two sides as shown.

Diagram showing shock absorber installation
Figure 4.6: Shock absorber installation. Ensure correct orientation and secure all fasteners.

4.7. Install the Front Basket

Use the screw to secure the plastic accessory to the rear of the basket. Align the mounting holes of the front basket mounting plate and secure it with bolts. Attach the basket to the front of the steerer tube, ensuring the plastic accessory hooks onto the bracket on the steerer tube. Pass the bolts through the holes on the metal plate, then tighten the bolts securely. Tighten the bolts to secure the bottom of the basket in place. Then use the plug to cover the screws in the slot.

Diagram showing front basket installation
Figure 4.7: Front basket installation. Secure the basket to the steerer tube and frame.

4.8. Install the Drop Stand

Place the drop stand behind the rear wheel, adjust it so that the tabs on the stand hook the slots on two sides. Then, align the mounting holes and tighten the bolts securely.

Diagram showing drop stand installation
Figure 4.8: Drop stand installation. Ensure it hooks into the slots and is securely bolted.

4.9. Install the Passenger Seat

Attach the passenger seat to the rear rack with the three hooks beneath the seat engaging into the corresponding slots, push the seat forward so that the mounting hole beneath the seat aligns with that on the rear rack. Firmly tighten the bolt to lock the passenger seat in place.

Diagram showing passenger seat installation
Figure 4.9: Passenger seat installation. Align hooks and mounting hole, then secure with bolt.

4.10. Install the Saddle

Align the three studs underneath the saddle with the mounting holes, attach the saddle to the mounting plate, and tighten the nut securely.

Diagram showing saddle installation
Figure 4.10: Saddle installation. Align studs and mounting holes, then tighten the nut.

4.11. Install the Rear Fender & Footrests

Attach the rear fender to the rear fender as shown, pass the bolts through the reflector's mounting holes and those on the rear fender, and tighten the bolts and nuts with the supplied tools. Place the rear fender over the rear wheel, align the mounting holes on the front of the rear fender with those on the brackets, and tighten the bolts securely. Pass the bolts through the mounting holes of the footrests and then the rear fender, then tighten the bolts securely.

Diagram showing rear fender and footrests installation
Figure 4.11: Rear fender and footrests installation. Secure all components with bolts and nuts.

5. Basic Operations

Before each ride, check the tires. If they feel soft or spongy, inflate them to the proper pressure.

Image showing the Battery Disconnect Switch location
Figure 5.1: Battery Disconnect Switch.

5.1. Battery Disconnect Switch

The Battery Disconnect Switch is toggled to "OFF" during shipping to prevent battery drain. Toggle it to the "ON" position before each ride. Toggle it to the "OFF" position for long-term storage.

5.2. Power ON/OFF

Place an NFC Key Card flat against the front of the display to power on the scooter.

Image showing NFC card being used to start the scooter
Figure 5.2: Smart unlocking with NFC card start.

5.3. Headlight ON/OFF

Toggle the Headlight Switch to turn on/off the headlight and taillight simultaneously while the scooter is powered on.

5.4. Riding Mode

Press the "S" Button while the scooter is powered on to cycle through riding modes. The riding mode defaults to "1" after each restart.

Speed settings: 6/10/15/25 km/h. After unlocking: 15/25/35/45 km/h.

Video 5.1: Demonstrates the scooter in use, highlighting features like NFC start, speed modes, IPX4 waterproof rating, shock absorbers, saddle, front basket, rearview mirrors, and automatic brake lights.

5.5. Horn

Press or hold the "Horn" Button while the scooter is powered on.

5.6. Anti-Theft Alarm

Moving the scooter while it is powered off will trigger the anti-theft alarm.

5.7. P Mode (Parking Mode)

The scooter will enter the "P" mode every time you restart it. In this mode, it will not accelerate when you twist the throttle. To exit the "P" mode, squeeze the left or right brake lever. Then, you can twist the throttle to accelerate the scooter. The scooter will enter P mode again after 20 seconds of inactivity.

6. Display

The large 4.5-inch round color LED screen provides clear information about your ride.

Detailed diagram of the Y16 Electric Scooter LED display with numbered indicators
Figure 6.1: LED Display Indicators.
  1. Headlight is on
  2. "Ready to Start" Prompt
  3. Real-time Speed
  4. Riding Mode
  5. Battery Level
  6. Battery Voltage
  7. Error Codes
  8. Odometer

6.1. Speed Levels

Riding ModeMax Speed (European)Max Speed (North American)
P (Parking)0 km/h0 mph
16 km/h9 mph
210 km/h15 mph
315 km/h21 mph
425 km/h28 mph

Note: The maximum speed after unlocking is 45 km/h (European) or 28 mph (North American).

6.2. Error Codes

The following are common error codes you may encounter. If you experience any of these or other error codes, contact customer support.

  • Motor Fault (M): Indicates an issue with the motor.
  • Controller Fault (ECU): Indicates an issue with the electronic control unit.
  • Brake Fault (!): Indicates an issue with the braking system.
  • Throttle Fault (Throttle icon): Indicates an issue with the accelerator.

7. Charging

Proper charging practices ensure the longevity of your scooter's battery.

Diagram showing the charging port location on the scooter
Figure 7.1: Charging port location.
  • Please fully charge the battery before first use.
  • The scooter is fully charged when the charger indicator changes from red to green.
  • With charging protection, the scooter will cut off charging automatically after a full charge. However, it is not recommended to overcharge it.
  • Keep the charging port cover closed when not charging.
  • During charging, the scooter cannot be turned on.

8. Specifications

FeatureEuropean ModelNorth American Model
ModelY16Y16
Scooter Size (Unfolded)143 x 69 x 107 cm56.3 x 27.2 x 42 in (143 x 69 x 107 cm)
Weight36.3 kg76.1 lbs (34.5 kg)
Battery CapacityDC 48 V, 20 AhDC 48 V, 20 Ah
Range90-100 km50-62 miles (80-100 km)
Motor Power1200 W1200 W
Max Speed25 km/h28 mph (45 km/h)
Max Load Capacity120 kg264 lbs (120 kg)
Recommended Age14+14+
Charger InputAC 100-240 V, 50/60 HzAC 100-240 V, 50/60 Hz
Charger OutputDC 54.6 V, 2 ADC 54.6 V, 2 A
Charging Time9-10 h9-10 h
Operating Temperature20°C–25°C68°F–77°F (20°C–25°C)
Storage Temperature-20°C–40°C-4°F–104°F (-20°C–40°C)
Charging Temperature0°C–40°C32°F–104°F (0°C–40°C)
Waterproof RatingIPX4IPX4

Note: The range is measured in a laboratory under 100% battery level condition. Actual range will differ depending on factors such as load, humidity, wind speed, and operation habits. For the best riding experience, 70% of the maximum load is recommended.

9. User Tips

  • Unlocking Speed: To unlock the scooter to its maximum speed (45 km/h or 28 mph), hold the throttle all the way and simultaneously hold the front brake. Repeat this combination to lock it back to restricted speeds.
  • Assembly Assistance: While assembly is not overly complicated, it can be challenging. Consider watching an assembly video for visual guidance if available. You may contact customer service for a link to the video.
  • Range Considerations: The stated range of 90-100 km is under ideal laboratory conditions. Actual range will vary significantly based on factors like rider weight, terrain (uphill climbs reduce range), speed, temperature, and riding style. Expect lower range when riding at higher speeds or on hilly terrain.
  • Braking Performance: The drum brakes are effective on flat roads. For optimal safety, especially on slopes or at higher speeds, anticipate braking needs and apply brakes smoothly.
  • Passenger Use: The scooter is rated for two seats. Ensure any passenger, especially a child, is securely seated and appropriate safety measures are taken.

10. Troubleshooting

This section addresses common issues and error codes you might encounter.

10.1. Common Error Codes

  • Motor Fault (M): If this error appears, check for any obstructions in the motor or wheel. If the issue persists, contact support.
  • Controller Fault (ECU): This indicates an internal electronic issue. Try restarting the scooter. If the error remains, contact support.
  • Brake Fault (!): Inspect brake levers and cables for any damage or disconnections. Ensure the brake cut-off system is functioning correctly.
  • Throttle Fault (Throttle icon): Check the throttle for smooth operation and ensure no debris is interfering with its movement. If the throttle is unresponsive, contact support.

10.2. Other Issues

  • Difficulty with Assembly Screws: Some users reported difficulty with certain screws during assembly, particularly for the front basket and rear seat. Ensure you are using the correct tools and applying appropriate force. If a screw seems stuck, avoid excessive force to prevent stripping; contact support for advice.
  • Reduced Range: If you experience significantly less range than advertised, consider factors such as rider weight, terrain (hills), average speed, ambient temperature, and tire pressure. Ensure tires are properly inflated.
  • Scooter Not Turning On: Check the Battery Disconnect Switch (Figure 5.1) is in the "ON" position. Ensure the battery is charged.
  • Scooter Not Accelerating in P Mode: This is normal. Squeeze either brake lever to exit P mode.

For any persistent issues or error codes not listed here, please contact customer support.

11. Maintenance

Regular maintenance will ensure the longevity and safe operation of your IScooter Y16.

  • Tire Pressure: Regularly check and maintain proper tire pressure. Inflate if tires feel soft or spongy.
  • Cleaning: Clean the scooter regularly with a damp cloth. Avoid using high-pressure water jets directly on electronic components. The scooter has an IPX4 waterproof rating, meaning it is resistant to splashing water from any direction, but not submersion.
  • Battery Care: Do not overcharge the battery. For long-term storage, toggle the Battery Disconnect Switch to "OFF". Store the scooter in a cool, dry place within the recommended storage temperature range (-20°C to 40°C).
  • Brakes: Periodically check the drum brakes for wear and proper function. Adjust or replace as needed.
  • Fasteners: Periodically check all bolts and nuts for tightness, especially after initial assembly and the first few rides.
  • Suspension: Inspect the front and rear spring shock absorbers for any signs of damage or reduced performance.

12. Safety & Compliance

Your safety is paramount. Please adhere to all safety guidelines and local regulations.

12.1. General Safety Guidelines

  • Always wear appropriate protective equipment, including a helmet, while riding.
  • Familiarize yourself with local laws and regulations regarding electric scooters and motorcycles. Note that road approval and registration requirements vary by region (e.g., some models may not be approved for German roads).
  • The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.
  • Children should be supervised to ensure they do not play with the appliance.
  • Exercise caution when riding in wet conditions, despite the IPX4 rating.
  • Be aware of your surroundings and traffic at all times. The scooter is equipped with rearview mirrors for total visibility.

12.2. Disclaimer

Please mind potential fire risk and strictly follow the instruction manual for charging and storage. While using the product, please wear protective equipment and fully comply with the applicable law and regulations.

12.3. Certifications

This product is CE certified.

12.4. FCC & ISED Statement

This device complies with Part 15 of the FCC Rules and ISED Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet general RF exposure requirements and can be used in portable exposure conditions. For full details, refer to the FCC ID: 2BM88-Y16 and IC: 34085-Y16 statements.

13. Warranty & Support

For support, inquiries, or to obtain the full text of the EU Declaration of Conformity, please contact the manufacturer or authorized representative.

  • Manufacturer: Dongguan Yicheng Shengda Information Technology Co., Ltd.
  • Manufacturer Address: Room 301, No. 28, Houshan Road, Nanchongkou, Humen Town, Dongguan City, Guangdong Province, China
  • Manufacturer E-mail: support@e-scootworld.com
  • EU Authorized Representative (EC REP): GAVIMOSA CONSULTORIA, SOCIEDAD LIMITADA
  • EU REP Address: CASTELLANA 9144, 28046 Madrid
  • EU REP E-mail: compliance.gavimosa@outlook.com
  • EU REP Phone: +34 688185858
  • EU REP Contact: Jorge Wilson

Disposal of Electrical and Electronic Equipment: The crossed-out garbage can symbol indicates that these devices must be disposed of separately from unsorted municipal waste. If products contain batteries, they must be removed before disposal and disposed of separately.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.