COOSPO AP-E1

Contents

COOSPO AP-E1 Electric Air Pump User Manual

Model: AP-E1 | Brand: COOSPO

1. Product Introduction

The COOSPO AP-E1 is a smart, portable electric pump designed for inflating bicycle tires, balls, and various other inflatables. It features smart pressure control, allowing you to preset the target pressure and automatically start or stop inflation. The pump is equipped with multiple nozzles to fit different types of inflatables.

2. Basic Specifications

ParameterValueParameterValue
ModelAP-E1Operating Temperature0~45°C
Product Size53×75×34.5mmBattery Specifications7.4V/3.7Wh
Net Weight131gInput ParametersDC 5V 2A
TypeElectricCertificationCE

3. Setup

3.1. Package Contents

The package for your COOSPO AP-E1 Electric Air Pump includes the following items:

  • Electric Bike Pump (AP-E1)
  • Type-C Cable
  • Schrader Valve adapter
  • Presta Valve adapter
  • Ball Needle
  • Extension Hose
  • User Manual (PDF available here)
  • Storage Bag
COOSPO AP-E1 Package Contents
Image: All items included in the COOSPO AP-E1 Electric Air Pump package.

3.2. Parts Description

Familiarize yourself with the components of your AP-E1 pump:

  • Preset Pressure / Actual Pressure Display: Shows the target and current pressure.
  • Unit Display: Indicates the pressure unit (PSI/BAR).
  • Power Switch: Used for turning the device on/off and starting/stopping inflation.
  • Battery Indicator: Shows the current battery level.
  • Pressure Adjustment Button: Used to cycle through preset pressure values.
  • Air Nozzle Interface: Where valve adapters are connected.
  • Type-C Input: Charging port.
COOSPO AP-E1 Pump with labeled controls
Image: Front view of the COOSPO AP-E1 pump with controls and display labeled.

3.3. Charging the Pump

To charge the pump, connect the provided Type-C charging cable to the pump's Type-C input and a power adapter (not included). The battery indicator will flash during charging and show a steady green light when fully charged.

COOSPO AP-E1 Pump charging via Type-C
Image: The COOSPO AP-E1 pump connected to a Type-C charging cable.

4. Operating Instructions

4.1. Power On/Off and Start/Stop

  • Power On: Press and hold the power button for 3 seconds. The power button will light up, and the pressure indicator will start flashing.
  • Start/Stop: Short press the power button to start or stop the air pump.
  • Power Off: Long press the power button for 3 seconds to turn off the air pump.

4.2. Valve Connection

Ensure you select the correct valve adapter for the item you wish to inflate.

  • Schrader Valve: Connect the Schrader valve adapter to the pump nozzle, then connect it to the item's valve. This is common for mountain bikes, e-bikes, and city bikes.
  • Presta Valve: Unscrew the French valve cap of the tire, then press the Presta valve adapter onto the tire valve to inflate. This is common for road bikes.
  • Ball Needle: Tightly screw the ball needle onto the valve interface and insert the needle into the ball's inflation hole.
How to use COOSPO AP-E1 pump
Image: Step-by-step visual guide on connecting the pump and starting inflation.

4.3. Switching Modes and Adjusting Pressure

When the pump is on, short press the pressure switch button to adjust the preset pressure. The LED corresponding to the selected preset will flash. During inflation, a steady LED indicates the real-time pressure, while a flashing LED indicates the preset pressure.

Pump ModeDefault Value (PSI)Corresponding Pressure (BAR)
Ball Mode8PSI0.6BAR
MTB / E-Bike Mode38PSI2.6BAR
Road Bike (Soft) Mode60PSI4.1BAR
Road Bike (Medium) Mode100PSI6.9BAR
Road Bike (Hard) Mode120PSI8.3BAR

4.4. Inflation Procedure

  1. Select the correct valve type according to the item to be inflated and connect it properly.
  2. Long press the power button for 3 seconds to turn on the pump.
  3. Short press the pressure switch button to choose the corresponding mode (the preset pressure LED will flash).
  4. Short press the power button to start inflating.
  5. The pump will automatically stop when the preset pressure is reached.
  6. Long press the power button for 3 seconds to turn off the pump and disconnect the valve.
Video: Demonstration of the COOSPO E1 Mini Bicycle Pump in use, showing connection, setting pressure, and inflation process.

4.5. Common Product Pressure Reference

To ensure safety, always check the required inflation pressure of the item before inflating. Over-inflation can cause bursting and personal injury.

  • Bicycle Tires: The allowable pressure range is marked on the sidewall of the tire.
  • Balls: The recommended pressure is marked around the valve.
Product TypePSI Pressure RangeBAR Pressure Range
Bicycle Tires18~30 PSI1.24~2.07 BAR
10-16 inch tires30~45 PSI2.07~3.10 BAR
20-30 inch tires38~55 PSI2.62~3.79 BAR
Road Bikes100~120 PSI6.89~8.27 BAR
Electric Wheelchair30~45 PSI2.07~3.10 BAR
Toy Balls3~6 PSI0.21~0.41 BAR
Children's Bikes7~9 PSI0.48~0.62 BAR
Basketball7~9 PSI0.48~0.62 BAR
Football10~12 PSI0.69~0.83 BAR

5. Maintenance

5.1. Battery Indicator

The battery LED shows different battery levels:

  • Sufficient battery: Green LED steady on.
  • Low battery: Red LED steady on (low battery, please charge before use).

Note: Do not use the pump during charging.

5.2. Battery Maintenance

If the product has not been used for more than six months, charge it every three months to maintain battery performance.

6. Troubleshooting

ProblemExclusion Methods
Slow inflation speed
  1. Check if the battery is sufficient.
  2. Check for air leaks between the valve and the tire valve.
  3. Make sure the valve connection is tightened properly.
  4. Check if the item being inflated is leaking.
Pump is on but cannot inflate
  1. Check if the current tire pressure is higher than the preset value.
Inflates normally but pressure shows zero
  1. Items with very low pressure (e.g., balloons) cannot be measured by the device.
  2. For empty tires, inflate for a short time before the pressure value is displayed.
LED color during inflation does not match standby stateDuring discharge, the lithium battery may show a noticeable voltage drop, causing the LED color in inflation to differ from the standby state. This is not a malfunction.
Battery LED does not light during chargingUse a certified charging cable and adapter to recharge safely.
Pump turns off automatically during use
  1. Check the battery level. Please fully charge before use.
  2. The pump has a 3-minute auto-shutoff for protection. Long press the power button to turn it on again.

7. Safety Warnings and Precautions

7.1. General Safety Warning

  • Do not leave the pump unattended during inflation.
  • Do not place the electric bike pump near flammable and explosive items.
  • Avoid dirt, sand, and dropping the pump.
  • Do not store the product in excessively cold, hot, or humid environments.
  • The product contains a lithium battery. Do not throw it into fire or dispose of it improperly.
  • Keep the product away from children.

7.2. High Temperature Safety Precautions

  • When removing the valve, the valve and valve connector may become hot after prolonged use. Please do not touch them directly.
  • If the pump temperature is too high, both the battery LED and the 120 PSI LED will flash red. Stop using the pump and let it cool down. Resume use only after the two LEDs stop flashing red.

7.3. Product Handling Warnings

  • Do not open or modify the product.
  • Do not disassemble or attempt to service this product.
  • This product is safe under normal and reasonably foreseeable operating conditions.
  • If the product is operating improperly, contact COOSPO support.
  • The product must be returned to the manufacturer for any service or repair.
Warning symbols for electrical products
Image: Universal warning symbols for electrical products, indicating caution and electrical hazard.

8. User Tips

  • The pump is well-built and effective, though it may produce some noise during operation.
  • Its lightweight and compact design make it highly portable, easily fitting into a bike bag.
  • The fast charging capability (approx. 40 minutes for a full charge) and long battery autonomy are significant advantages for on-the-go use.
  • It's advisable to test the pump's functionality before critical cycling trips to ensure optimal performance.

9. Warranty and Support

9.1. Contact Information

9.2. Attentions and Disclaimer

The information in this manual is for reference only. The product may be subject to alterations due to ongoing research and development without prior notice. The manufacturer is not liable for any direct or indirect damages arising from the use of this manual or the product.

9.3. FCC Statement

This device complies with Part 15 of the FCC Rules, ensuring it does not cause harmful interference and accepts any interference received. If interference occurs, try reorienting the receiving antenna, increasing separation between equipment and receiver, or connecting to a different circuit. Consult a dealer or technician for assistance.

9.4. IC Warning

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's license-exempt RSS(s). Operation is subject to not causing interference and accepting any interference, including that which may cause undesired operation.

9.5. Disposal Information

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Contact your local government or a retailer for additional information.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.