Flytec V066 GPS Bait Boat

Contents

Flytec V066 GPS Bait Boat User Manual

GPS Brushless Motor 12V High-Speed RC Bait Boat

1. Product Introduction

1.1 Boat Hull Parts

The Flytec V066 GPS Bait Boat is available in both single and dual silo versions, designed for efficient bait delivery and fishing. Below is a detailed breakdown of the boat's main components.

Diagram showing the main parts of the bait boat hull, including antenna, silo, switch, headlight, hook, propeller, waterproof grass cover, handles, and battery indicator.
Boat Hull Part Description: This diagram labels key components such as the Antenna, Silo, Switch, Headlight, Hook, Propeller, Waterproof Grass Cover, Handles, and Battery Indicator.
Image showing both single and dual silo versions of the bait boat, filled with different types of bait.
Silo Versions: The V066 bait boat is available in both single and dual silo configurations, allowing for versatile bait deployment.

1.2 Buzzer Prompt Instructions

  • Low Battery Warning: Both the boat and the remote controller will emit a continuous "beep-beep-beep" sound when their respective batteries are in low capacity.
  • Successful Operation: Pressing any button on the remote control will result in a single "beep" sound upon successful operation.
  • Arrival Notification: A "beep-beep" sound is emitted when the boat arrives at a designated cruise point or original point.

2. Setup

2.1 Antenna and Battery Installation

Follow these steps to prepare your bait boat for operation:

  1. Install Antennas: Install the two antennas onto the boat and tighten them securely.
  2. Access Battery Compartment: Unscrew the nut and remove the battery compartment cover.
  3. Insert Battery: Insert the 11.1V 18000mAh battery into the compartment. Ensure the power interface faces forward.
  4. Secure Battery: Secure the battery with Velcro straps and plug in the power cord.
  5. Close Compartment: Install the battery compartment cover and screw back the nut.
Sequence of images showing how to install antennas, open the battery compartment, insert the battery, connect the power, and close the compartment.
Battery Installation Steps: Visual guide for installing the boat's battery and antennas.

2.2 Remote Control Button Description

The remote control features a high-definition color screen and intuitive buttons for easy one-handed operation.

Diagram of the remote control with all buttons labeled, including joystick, cruise/setting point, hook/calibration, fishing ground, cursor left/right, speed/electronic anchor, silo selection, original point, clear, lighting, and OK buttons.
Remote Control Buttons: This diagram labels each button and its primary function for controlling the bait boat.

2.3 Geomagnetic Calibration

Geomagnetic calibration ensures accurate navigation. Perform this step before operating the boat in water.

  1. Position the Boat: Drive the boat 5-6 meters away from the shore.
  2. Initiate Calibration: Press and hold the hook button on the remote control for about 3 seconds.
  3. Calibration Sequence: The boat will automatically turn right twice, then left twice, and stop rotating to complete calibration.
Diagram showing the boat performing turns for geomagnetic calibration and the remote control button to initiate it.
Geomagnetic Calibration Process: Visual steps for calibrating the boat's compass.

3. Operation

3.1 Screen Display Instructions

The remote control's HD color screen provides real-time information about the boat's status and environment.

Detailed diagram of the remote control screen showing satellite number, signal, compass, boat lights, tow hook, boat power, remote control power, boat direction, distance to position point, original point, silo status, and positioning points.
Remote Control Screen Details: This image explains the various indicators on the remote control screen for comprehensive boat monitoring.
  • Satellite Signal: The icon is always on after frequency matching and GPS signal acquisition.
  • Satellite Number: Displays '00' initially. Changes in real-time when 8 or more satellites are found.
  • Compass: Indicates the boat's bow direction. Defaults to 'N' when not linked.
  • Boat Lights: Shows light status: "steady on - flashing - off".
  • Tow Hook: Flashes when activated, stays on after reset.
  • Boat Power: Displays current boat battery level after pairing.
  • Remote Control Power: Displays current remote control battery level after powering on.
  • Boat Direction: Flashes blue during fixed-speed cruise control, indicating forward, backward, left, or right turns.
  • Distance Between Boat and Position Point: Shows remaining distance to target point after setting. Displays '0' when reached.
  • Original Point: Blue icon lights up after setting.
  • Distance Between Boat and Original Point: Real-time distance display.
  • Fishing Ground Number: A, B, C, D represent four fishing grounds. Select one before setting position points.
  • Silo: Flashes blue when selected, red when ejected, returns to white after reset. Both silos flash simultaneously for single silo versions.
  • Positioning Point: Unset points are red, selected points flash, set points are yellow. Electronic anchor points are blue.

3.2 Sailing Direction

Control the boat's movement using the joystick on the remote control.

  • Forward: Push the joystick forward.
  • Backward: Pull the joystick backward.
  • Turn Left: Move the joystick left.
  • Turn Right: Move the joystick right.

3.3 Fixed-speed Cruise Control

Engage cruise control for hands-free operation.

  1. Activate Cruise Control: Push the joystick upward for 5 seconds. The remote control will emit a "beep" sound, and the cursor on the screen will flash, indicating successful activation.
  2. Exit Cruise Control: Push the joystick backward. The remote control will emit a "beep" sound, and the cursor will be steady on, indicating successful exit.
Image showing the remote control and boat on water, illustrating how to activate fixed-speed cruise control by pushing the joystick up for 5 seconds.
Fixed-speed Cruise Control: Push the joystick up for 5 seconds to engage cruise control, allowing you to easily free your hands.

3.4 Bait Release (Silo Release)

The bait boat features independent control for single or dual silos, with a large capacity of 3kg for bait loading.

Image showing the bait boat with 3KG bait capacity, suitable for pelleted feed, corn kernels, and mixed feed.
Bait Capacity: The boat has a 3KG bait capacity and is suitable for various feed types.

Dual Silo Version:

  1. Select Silo: Short press the silo selection button to switch between the right and left silos. The selected silo icon will flash blue.
  2. Release Bait: Short press the OK button to release bait from the selected silo. The silo icon will flash red and return to white after reset.

Single Silo Version:

  1. Select Silo: Short press the silo selection button. Both silo icons will flash blue simultaneously.
  2. Release Bait: Short press the OK button to release bait. Both silo icons will flash red and return to white after reset.

Note: The silo knob cannot be manually rotated to reset. To reset, press the button again to release the corresponding silo knob, and quickly manually reset the silo before the knob resets.

3.5 Electronic Anchor Mode

The electronic anchor function allows the boat to maintain a fixed position against current and wind.

  1. Navigate to Anchor Point: Drive the boat to the desired location for the electronic anchor point.
  2. Set Anchor Point: Long press the Speed/Electronic Anchor button to set this location as the electronic anchor point. The electronic anchor point icon will turn blue.
  3. Exit Anchor Mode: Long press the Speed/Electronic Anchor button again to exit electronic anchor mode.
Image showing the bait boat on water with a graphic representing the electronic anchor function, indicating it resists current and wind interference.
Electronic Anchor Function: This feature allows the boat to remain fixed at a precise point, resisting environmental interference.

Note: Once the electronic anchor point is set, the joystick's left/right movement and the clear key are disabled. Long pressing the joystick will not activate cruise control. Only the light, OK, hopper selection, and tow hook keys remain functional.

3.6 Fishing Ground Settings

The V066 allows you to set up to 4 fishing grounds and 200 positioning points for diverse fishing needs.

Image showing the bait boat on water with multiple numbered pins indicating fishing spots and GPS+Beidou dual-mode positioning.
Accurate Fishing Spot Location: The boat can accurately locate and memorize up to 200 fishing spots across 4 fishing grounds using GPS+Beidou dual-mode positioning.

Select Fishing Ground:

  1. Short press the Fishing Ground button to switch between fishing grounds A, B, C, and D. The selected fishing ground will have a blue background with flashing letters.

Confirm Fishing Ground:

  1. The blue background of the set fishing ground will always be on.

3.7 Original Point Setting & One-click Return

The boat can return to a set original point with a single click, or automatically under certain conditions.

Image showing the bait boat on water with graphics indicating smart return features: low battery return, one-click return, and loss signal return.
Smart Return Features: The boat offers smart return functions including low battery return, one-click return, and loss signal return to prevent loss.

Set Original Point:

  1. Short press the Original Point button. The blue icon will light up.

Clear Original Point:

  1. Long press the Original Point button. The blue icon will disappear.

One-click Return:

  1. Long press the Original Point button. The boat will return to the set original point.

Cancel One-click Return:

  1. Press and hold the Original Point button again or push the joystick down.

3.8 Positioning Point Setting & Cruise

Set and navigate to specific positioning points for precise baiting.

Setting a Positioning Point:

  1. Short press the Cruise/Setting Point button to enter positioning point selection.
  2. Use the cursor buttons to select a point number (01-10). The selected number will flash.
  3. Short press the OK button to confirm the positioning point. The set point will have a yellow background.

Cruising to a Positioning Point:

  1. Short press the Cruise/Setting Point button to enter positioning point selection.
  2. Use the cursor buttons to select the desired point.
  3. Long press the Cruise/Setting Point button to cruise to that point. The corresponding point number will flash during cruising.
  4. To cancel cruising, long press the Cruise button or push the joystick down.

Deleting a Positioning Point:

  1. Short press the Cruise/Setting Point button to enter positioning point selection.
  2. Use the cursor buttons to select the point to delete.
  3. Short press the Clear button to delete the corresponding point. Long press the Clear button to delete all points (the origin point is not cleared).

3.9 Electronic Fence

The electronic fence function prevents the boat from sailing beyond a set safe distance.

Image showing the bait boat on water with a graphic representing an 800-meter electronic fence boundary.
Electronic Fence: Set an 800-meter safety range to prevent the boat from sailing beyond it.

After setting the origin, the boat will activate the electronic fence function, and it cannot sail out of a safe distance of 800m from the origin.

3.10 Speed Switching

The boat features a Hurricane Brushless Dual-Speed Adjustable motor, allowing for speeds up to 20 km/h.

Image showing the bait boat speeding on water with a speedometer indicating 20 km/h.
Dual-Speed Adjustable: Easily switch between two speeds, with a top speed of 20 km/h, thanks to the brushless core.

Short press the Speed/Electronic Anchor button to switch between slow and fast speeds. The initial gear is slow speed.

  • Slow Speed: When switching to the first gear, the remote control will beep once.
  • Fast Speed: When switching to the second gear, the remote control will beep twice.

3.11 Lighting Control

The bow is equipped with 2 high-brightness night navigation lights for visibility in low light conditions.

Image of the bait boat on water at dusk with its headlights on.
Night Navigation Lights: The boat's headlights provide high-brightness illumination for clear identification at night.

Short press the Lighting button to cycle through "Steady on - Flashing - Off" modes. The default light status after frequency matching is "Steady on".

3.12 Tow Hook

The boat is equipped with a high-torque net-pulling device for easy one-touch trawling and net-release.

Image showing the bait boat pulling a fishing net, with text describing its high-efficiency pulling net and hook feature.
Pulling Net and Hook: The boat is equipped with a high-torque net-pulling device for efficient fishing.

Short press the Hook/Calibration button to retract the tail link. The hook icon will flash when activated and stay on after reset.

4. Charging Instructions

Proper charging ensures optimal performance and longevity of your bait boat.

4.1 Boat Battery Charging

The boat is powered by an 11.1V 18000mAh large-capacity battery with a modular design for easy installation and removal.

Image showing the large-capacity 11.1V 18000mAh battery and the boat, highlighting the modular battery design.
Large-Capacity Battery: The 11.1V 18000mAh battery provides extended usage, and its modular design simplifies installation and removal.
  1. Connect the European charger to a power outlet.
  2. Connect the charging cable to the boat's battery power socket.
  3. The plug indicator light will be red during charging and turn green when charging is complete.
  4. Charging time is approximately 7 hours.

4.2 Remote Control Charging

  1. Connect the Type-C charging cable to a USB adapter and the bottom port of the remote control.
  2. The remote control screen will display a 0-3 bar power cycle during charging. Once fully charged, 3 bars will be displayed steadily.
Diagram showing charging indicators for both the hull battery and the remote control, with estimated charging times and battery level displays.
Charging Indicators: Visual guide for understanding the charging status of both the boat's hull battery and the remote control.

Note: When the battery is low, drive the boat back and charge it in time to avoid losing the boat.

5. Maintenance Guide

Regular maintenance ensures the longevity and optimal performance of your bait boat.

5.1 Motors

Check the motors for any tangled debris after each use to prevent damage and ensure smooth operation.

5.2 Boat Hull

Images showing the top and bottom views of the bait boat hull, highlighting its design and propellers.
Boat Hull: The boat hull is designed for durability and efficient water displacement.
  1. Cleaning: After each use, wipe the boat dry to keep the hull clean and prevent water damage.
  2. Battery Storage: If the battery will not be used for a long time, remove it from the boat and charge it for storage.
  3. Chemicals: Do not store corrosive liquids or items near the boat.
  4. Heat Exposure: Keep the boat away from high-temperature objects.
  5. Dust Protection: When not in use, store the boat in a clean, dust-free environment.

6. Specifications

Detailed technical specifications for the Flytec V066 GPS Bait Boat.

Product information table detailing item number, bait load, boat size, battery, playing time, packing list, material, color, net weight, control distance, and charging time.
Product Information Table: This table provides a quick overview of the boat's key specifications and included items.
FeatureSpecification
Item No.V066 GPS
MaterialABS
ColorBlack
TypeBait Thrower
Bait Load Capacity3 kg
Boat Size (L*W*H)57.5 cm * 31 cm * 25 cm (22.64 in * 12.2 in * 9.84 in)
Net Weight3781 g
Battery11.1V 18000mAh
Playing TimeUp to 4 hours (approx. 3 hours with 18000mAh battery)
Control Distance1000 M
Charging Time7 hours
Motor TypeBrushless (12V 20A + 172.26W + 7160r/min)
PropellerUpgraded four-blade design (6cm diameter)
Waterproof RatingIP68 (waterproof, silt-proof, salt-resistant)
GPS PositioningGPS+BeiDou dual-mode, 200 positioning points, 4 fishing grounds
Electronic Fence Range800 meters
Max Speed20 km/h
Included AccessoriesBoat*1, boat battery*1, Remote Control*1, Hanging Rope*1, European Charger*1, Type-C Remote Control Charging Cable *1, Instruction Manual*1, Antenna*2, Spare Propellers*2, Boat Bag*1, Boat Rack*1 (Note: Spanner included with single-silo version, Propeller & Nut*2 with dual-silo version)
Diagram showing the dimensions of the dual-silo bait boat.
Boat Dimensions (Dual-silo Version): Length 57.5cm (22.64in), Width 31cm (12.2in), Height 25cm (9.84in).
Diagram showing the dimensions of the single-silo bait boat.
Boat Dimensions (Single-silo Version): Length 57.5cm (22.64in), Width 31cm (12.2in), Height 25cm (9.84in).

7. User Tips

  • Pre-Operation Check: Always ensure the battery is fully charged and the antennas are securely installed before each use.
  • Geomagnetic Calibration: Perform geomagnetic calibration in an open area, away from magnetic interference, to ensure accurate navigation.
  • Bait Loading: Distribute bait evenly in the silos to maintain boat stability, especially for the dual-silo version.
  • GPS Signal: Wait for the GPS signal icon to be steady on before setting fishing points or using advanced navigation features.
  • Water Conditions: Utilize the dual-speed feature to adapt to different water conditions, using lower speeds for precise maneuvering and higher speeds for covering distances.
  • Night Fishing: Make use of the high-brightness night navigation lights for better visibility and safety during low-light conditions.
  • Battery Management: Pay attention to low battery warnings and return the boat to shore promptly to avoid losing it.

8. Troubleshooting

  • Boat Not Responding: Check remote control battery level and boat battery level. Ensure the boat and remote are properly paired.
  • Inaccurate Navigation: Perform geomagnetic calibration. Ensure a strong GPS signal is acquired.
  • Bait Not Releasing: Check if the silo is properly loaded and if the release mechanism is clear of obstructions. Verify the remote control command is registered (single beep).
  • Boat Drifting in Electronic Anchor Mode: Ensure the electronic anchor point was set correctly. Check for strong currents or winds that might exceed the boat's resistance capabilities.
  • Boat Not Returning: Verify that an original point was set before initiating a return. Check for low battery or signal loss, which might trigger automatic return.
  • Reduced Speed/Power: Check for tangled debris in the propellers. Ensure the battery is fully charged.

9. Warranty & Support

For any issues or questions regarding your Flytec V066 GPS Bait Boat, please refer to the seller's support channels. Keep your purchase receipt for warranty claims. This manual provides general operational guidelines; specific warranty terms and conditions are provided by the seller at the time of purchase.

10. Product Video

Watch this video for a visual demonstration of the Flytec V066 GPS Bait Boat's features and operation.

Flytec V066 GPS Bait Boat Demonstration: This video showcases the boat's features, including its brushless motor, dual-silo bait release, GPS functionality, and remote control operation.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.