HGLRC Nblade Max

Contents

HGLRC Nblade Max 5inch FPV Frame User Manual

Model: Nblade Max | Brand: HGLRC

1. Introduction

The HGLRC Nblade Max is a high-performance 5-inch FPV (First Person View) drone frame designed for enthusiasts seeking durability and versatility in their builds. Crafted from a combination of carbon fiber and aluminum, this frame offers robust protection for your electronics while maintaining a lightweight profile crucial for agile flight. It supports both True-X and DC (Dead Cat) configurations, allowing pilots to choose the layout that best suits their flying style and camera requirements. This manual provides essential information for assembling, operating, and maintaining your Nblade Max frame.

HGLRC Nblade Max 5inch FPV Frame (DC version) - front view
Figure 1: HGLRC Nblade Max 5inch FPV Frame (DC version) - front view

2. Specifications

Below are the detailed specifications for the HGLRC Nblade Max FPV Frame:

FeatureSpecification
ModelNblade MAX
MaterialCarbon Fiber + Aluminum
Frame Type5-inch (True-X / DC configurations)
Wheelbase (DC)221.5mm
Wheelbase (Positive X)226.5mm
Dimensions (DC)222x220mm
Dimensions (Positive X)205x220mm
Top Plate Thickness2mm
Mid-plate/Bottom Plate Thickness3mm
Front/Rear Arms Thickness6mm
Top/Bottom Plate Spacing21mm
FC Mounting Holes20x20mm
Supported Camera19x19mm / 20x20mm
Motor Mounting Holes16x16mm
Weight (DC frame)216g
Weight (Positive X frame)220g
Recommended Age14+ years
Batteries IncludedNo
HGLRC Nblade Max FPV Frame specifications table and comparison of DC vs Positive X configurations
Figure 2: Frame Specifications and Configuration Comparison

3. Package Contents

Upon opening your HGLRC Nblade Max FPV Frame package, please verify that all the following components are included. If any parts are missing or damaged, contact your retailer immediately.

Detailed exploded view and assembly steps for the HGLRC Nblade Max FPV Frame, showing all components and their placement.
Figure 3: Exploded View and Component List
  • Top Plate
  • Mid Plate
  • Bottom Plate
  • Front Arms (2x)
  • Rear Arms (2x)
  • Side Plates (2x)
  • Aluminum Standoffs (various sizes)
  • Screws (various sizes for frame assembly and component mounting)
  • Battery Strap
  • Anti-slip Battery Pad
  • TPU Parts:
    • Camera Mount
    • Antenna Mount
    • GPS Mount
    • Gopro/Action Camera Mount
    • Receiver Mount
    • VTX Antenna Mount
    • Capacitor Mount
    • Buzzer Mount
    • XT60 Mount
  • Motor Protection Pads
  • USB-C Extension Cable
  • LED Strip
  • Heat Shrink Tubing
  • Zip Ties

4. Assembly and Setup

Follow these steps carefully to assemble your HGLRC Nblade Max FPV Frame. Refer to Figure 3 for a visual guide to component placement.

4.1 Frame Assembly

  1. Attach Arms: Secure the front and rear arms to the bottom plate using the provided screws. Ensure the arms are oriented correctly for either the True-X or DC configuration as desired.
  2. Install Standoffs: Mount the aluminum standoffs onto the bottom plate. These will support the mid and top plates.
  3. Mount Mid Plate: Place the mid plate onto the standoffs and secure it with screws.
  4. Install Side Plates: Attach the carbon fiber side plates to the frame structure. These protect your camera and other components.
  5. Mount Top Plate: Secure the top plate to the remaining standoffs.

4.2 Electronic Component Installation

The Nblade Max frame is designed to accommodate standard FPV drone components. Ensure all components are securely mounted and wiring is neat to prevent interference and damage.

  • Flight Controller (FC) & Electronic Speed Controller (ESC) Stack: Mount your FC/ESC stack using the 20x20mm mounting holes. Use appropriate standoffs and vibration dampeners if necessary.
  • Motors: Attach your motors to the arms using the 16x16mm mounting holes. Ensure motor wires are routed safely and secured.
  • Camera: Install your FPV camera (19x19mm or 20x20mm compatible) into the front camera mount using the provided TPU parts.
  • Video Transmitter (VTX) & Receiver (RX): Mount your VTX and RX in suitable locations, often within the main body of the frame. Use the dedicated TPU mounts for antennas.
  • Battery: Secure the battery to the top or bottom plate using the battery strap and anti-slip pad.
  • Additional Components: Utilize the various TPU mounts for GPS, GoPro/action camera, buzzer, capacitor, and XT60 connector as needed for your build. The USB-C extension cable can be installed for easy access to your FC.
HGLRC Nblade Max FPV Frame with various mounted components (camera, antenna, GPS, action camera).
Figure 4: Frame with Mounted Components
HGLRC Nblade Max FPV Frame showing internal component layout and mounting points.
Figure 5: Internal Component Layout

5. Operating Instructions

This manual covers the assembly of the FPV frame. For detailed operating instructions of your complete FPV drone, please refer to the manuals provided with your flight controller, ESCs, motors, and radio system. Ensure all components are correctly configured and calibrated before your first flight.

  • Always perform pre-flight checks to ensure all screws are tight and components are secure.
  • Verify propeller direction and motor spin direction are correct.
  • Ensure your battery is fully charged and properly secured.
  • Fly in a safe and open area, away from people and obstacles.
  • Adhere to local regulations regarding drone operation.

6. Maintenance

Regular maintenance will extend the lifespan of your HGLRC Nblade Max frame and ensure safe flights.

  • Inspect for Damage: After each crash or hard landing, thoroughly inspect the carbon fiber plates and arms for cracks or delamination. Check aluminum standoffs for bends.
  • Tighten Screws: Periodically check and tighten all screws, especially those holding the arms and main plates. Vibration can cause screws to loosen over time.
  • Clean the Frame: Remove dirt, grass, and debris from the frame and around electronic components.
  • Check TPU Parts: Ensure TPU mounts are not torn or excessively worn, as they provide crucial protection and vibration dampening.
  • Arm Replacement: The 6mm arms are designed to be robust but can be replaced individually if damaged.

7. Troubleshooting

This section addresses common issues related to the FPV frame itself. For electronic component troubleshooting, refer to their respective manuals.

ProblemPossible CauseSolution
Excessive VibrationLoose screws, damaged arms, unbalanced propellers (not frame related)Check and tighten all frame screws. Inspect arms for cracks and replace if necessary. Ensure motors are securely mounted.
Components ShiftingLoose mounting screws, worn TPU partsEnsure all component mounting screws are tight. Replace any worn or damaged TPU mounts.
Frame FlexingDamaged carbon fiber, incorrect assemblyInspect all carbon fiber plates and arms for cracks. Ensure all standoffs and screws are correctly installed and tightened.

8. User Tips

  • Loctite for Screws: Consider using a small amount of blue thread locker (Loctite 243) on metal-to-metal screws to prevent them from vibrating loose during flight. Avoid using it on plastic or carbon fiber parts.
  • Cable Management: Use zip ties and heat shrink tubing to neatly route and secure all wiring. This improves airflow, reduces potential damage, and makes troubleshooting easier.
  • Arm Guards: While the 6mm arms are strong, consider adding additional arm guards (if available) for extra protection during aggressive flying or learning.
  • Spare Parts: It's always a good idea to keep spare arms, standoffs, and screws on hand for quick repairs after a crash.

9. Warranty and Support

For warranty information and technical support, please refer to the official HGLRC website or contact your authorized dealer. Keep your proof of purchase for any warranty claims.

© 2024 HGLRC. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.