1. Introduction
The Flytec V030 GPS Bait Boat is an advanced remote-controlled bait boat designed for fishing enthusiasts. It features GPS auto-navigation with 180 waypoints across 9 fishing grounds, an 800m control range, and optional sonar compatibility with a 4.3'' display. This manual provides essential information for safe and effective operation, maintenance, and troubleshooting.
2. Safety Warnings
When using this product, please follow the following security descriptions to avoid the risk of fire, electric shock or property/personal injury:
- Be sure to read the complete manual and safety warning before use.
- This product contains sensitive electronic components and parts, so please use this product carefully.
- Do not place this product in direct sun or dark & humid environment.
- Do not use this product under rainy/lightning weather.
- Do not go backwards after releasing the fishing net or fishing line so that can prevent from wrapped around the motor/propeller.
- Do not let the boat cross water plants or other obstacles to avoid the motor from being entangled.
- Always maintain the dryness and cleaning of this product.
- Do not clean it when this product is powered on. When this product is still humid, do not connect the power.
- When in use, it is recommended to tie the hanging rope on the remote control in order to hang it on the neck.
- Do not completely exhaust the battery.
- When using this product, please charge the battery and then use it.
- Please use the adapter provided to charge the battery.
- Do not power the product with the battery for a long time.
- If only two (or less than two) of the three LEDs of the boat's power indicator are displayed, please charge it immediately.
- When you do not use this product, remove the battery from the boat.
- Don't leave any cables that may be tripped or pulled unexpectedly.
- Do not use this product at high temperature environment.
- Do not fall down and damage the product.
- Before charging, please check whether the charger is damaged.
- Please use official parts to replace.
- If the product fails or stops working, please stop using and contact the supplier.
- Put the packaging materials and small accessories where children cannot reach.
3. Product Overview
3.1. Boat Components
The V030 GPS Bait Boat consists of several key components for its operation and functionality. Refer to the diagrams below for a visual guide.


3.2. Controller Details
The remote control features a comprehensive interface for managing the bait boat's functions. Familiarize yourself with the buttons and display icons.

4. Setup
4.1. Initial Preparation
- Please read this manual thoroughly before use.
- Carefully take the bait boat out of its packaging box.
- Remove any protective film from the boat.
- Install the antenna onto the bait boat.
- Use the provided adapter to charge both the boat battery and the remote control until fully charged.
- Open the battery compartment cover (refer to Figure 4.1), connect the boat battery to the boat's power cord (refer to Figure 4.2), and then securely close the battery compartment cover.
- The bait boat is now ready for operation.

4.2. Power On and Frequency Matching
Before operating, the boat and remote control must be successfully paired.
- Place the boat in a horizontal position. Hold down the calibration button on the remote control and turn on the boat switch.
- When the boat's tail lights start flashing, turn on the remote control switch.
- Frequency matching is successful when the remote control indicator light stays on and the boat signal icon appears on the screen.
After successful pairing, perform a simple operation on the shore to confirm the boat responds to the remote control. Note: When not operated in water, the boat's gyroscope may not be active, leading to functional abnormalities (e.g., only one motor working), which is normal.
4.3. Calibration
Once the remote control shows the GPS signal icon and the signal strength is greater than 9, calibration can be performed.
- Place the boat in the water and drive it approximately 7 meters away from the shore, ensuring no obstacles are nearby.
- Press the calibration button on the remote control. The boat will then enter automatic calibration, turning left in a circle, then right in a circle, and stopping upon completion.

5. Operating Instructions
5.1. Fishing Ground Settings
After calibration, you can set up to 9 fishing grounds (1-9), with each ground storing up to 20 anchor points.
- Long press the fishing ground button, then use the up/down buttons to select the desired fishing ground interface.
- Proceed to set the origin and other anchor points. If more anchor points are needed, switch to another fishing ground.
Note: Each fishing ground must have an origin point set before other anchor points. Anchor points between different fishing grounds do not affect each other. Remember to switch to the correct fishing ground if changing fishing locations, otherwise the boat will execute the auto return function.

5.2. Origin Settings
When the GPS signal is greater than 9, positioning points can be stored. It is recommended to set the origin point on the shore.
- Each fishing ground must first set the origin point at No. 01.
- Select '01' using the remote control selection button, then press the 'OK' button to confirm. The number '01' on the display will flash and then remain solid, indicating successful origin point settings.
5.3. Anchor Point Settings
After successfully setting the origin point, you can set additional anchor points.
- Drive the boat to the desired location.
- Select the corresponding number using the remote control selection button, then press 'OK' to confirm. The number on the display will flash and then remain solid, indicating successful anchor point setting.
- Repeat for up to 20 anchor points per fishing ground. A total of 180 anchor points can be set across 9 fishing grounds.

5.4. Cruise Control
- Select any successfully set anchor point via the remote control.
- Press the 'OK' button to start automatic cruising. The boat will navigate to the designated point, and the remote control screen will display the distance to that point.
- When the boat reaches approximately 1 meter from the target, the cruise ends. The display will then show the distance between the boat and the origin.
Note: If the boat deviates, re-calibrate and then operate. During cruise and return to origin, the remote control screen will display a return icon, indicating automatic driving.
5.5. Clearing Anchor Points
To clear individual anchor points:
- Select the corresponding anchor point on the remote control.
- Press the 'Clear' button. The anchor point icon will disappear, indicating it has been cleared.
To clear all anchor points in the current fishing ground, press and hold the 'Clear' button until all GPS positioning point icons disappear from the screen.
5.6. Cancelling Cruise
During an active cruise, press the 'Cancel' button on the remote control to stop the boat's autonomous driving.
5.7. Electronic Fence Protection
The boat's control distance is up to 800m. To prevent signal interference or delay at long distances, an electronic fence protection function is set at 500 meters. If the boat exceeds 500m, it will automatically return to within 500m and stop.

Note: If the boat is within 500m and you wish to return to the origin, press the 'Origin' button. The boat will return in a straight line. The fence return action cannot be cancelled. If switching to another fishing ground whose origin is more than 500m from the boat's current location, the fence function will automatically trigger. In this case, switch back to the original fishing ground and cancel the return.
5.8. Low Power Auto Return to Origin
When the boat's battery is low, the boat will automatically return to the origin of the current fishing ground. To enable this function, the origin point must be set first.
5.9. Fixed Speed Cruise
- Simultaneously push both remote control joysticks upwards.
- Press and hold the fixed-speed cruise button until the boat enters fixed-speed cruise mode.
- In this mode, the remote control can still adjust the boat's sailing direction.
Note: To exit fixed-speed cruise mode, press the fixed-speed cruise button again.

5.10. Bait Release
The bait hoppers can be controlled separately if the hopper partition is installed.
- Press the left hopper button to release bait from the left hopper. The left hopper icon on the remote control screen will flash.
- Press the right hopper button to release bait from the right hopper. The right hopper icon on the remote control screen will flash.

Note: If the hopper partition is not installed, press both the left and right hopper buttons simultaneously to release all bait. After baiting, the bottom hopper baffle needs to be manually closed.
5.11. Hook Hanging & Fishing Net Release
The boat has a hook control valve at the tail, controlled by the left and right hook control valve buttons.
- Press the corresponding hook control valve button to quickly put fish hooks or a fishing net when the lever is retracted.
- Once the device is restored, it can be successfully hung, and the boat can be driven for net release.
- After reaching the desired location, press the left hook control valve button to release the fishing net. The left hook control valve icon on the remote control screen will flash. The right hook control valve operates similarly.

5.12. Speed Switching
The boat has two speed gears, adjustable via the speed adjustment wheel on the remote control. A single 'DI' sound indicates low speed, while two 'DI' sounds indicate high speed.
5.13. Out of Control Automatic Return
If the boat's signal is poor, the boat signal icon on the remote control screen will disappear. If the boat remains in a poor signal state for a while, it will automatically return to the origin.
5.14. Remote Control Charging and Dormant Mode
Charging: Use the provided USB charging cable. The charging indicator light turns red during charging and turns off when complete.
Dormant Mode: If the remote control is not operated for 10 minutes and is not paired with the boat, it will automatically enter dormant/standby state. Turn off and then turn on the remote control to restore the previous operating interface. Fishing grounds and anchor point settings will be retained.
6. Maintenance
6.1. Remote Control
Power off the remote control when not in use to extend battery life.
6.2. Motor
After each use, check the motor for any tangled debris and remove it.

6.3. Bait Boat
- After use, dry the boat thoroughly to keep it dry and clean.
- For long-term storage, remove the battery and charge it.
- Do not store with corrosive liquids.
- Avoid proximity to hot objects.
- When not in use, store the boat to prevent dust contamination.
- After use, there may be a small amount of water in the drain outlet of the water cooling device on the bottom of the boat. Wipe this dry before storage.

6.3.1. Optional Fishfinder Installation
If you have the Fish Finder version, install the probe into the fishfinder bracket from top to bottom and connect it to the rear of the boat with the fishfinder bracket drag rope.

7. Troubleshooting
7.1. Common Issues and Solutions
- How long can I sail? Each battery can typically sail for 2 hours. Weather conditions (e.g., strong wind) can affect battery usage and make the boat consume more electricity.
- How far is the range? The distance between the remote control and the boat is up to 800 meters. Environmental factors significantly impact this distance, so sailing to the maximum range is not recommended.
- Remote control cannot control the boat? Power off both the remote control and the bait boat. Then, re-perform the frequency matching steps (refer to Section 4.2).
- GPS fails frequently? Ensure a clear line of sight for the GPS signal. Avoid operating in areas with heavy tree cover or tall structures that might block satellite signals. Re-calibrate the boat if GPS accuracy is consistently poor (refer to Section 4.3).
- Charging plug issues? Handle charging cables and ports with care. Avoid excessive force when plugging/unplugging. If the plug is damaged, contact the seller for official replacement parts.
8. Specifications
Below are the key specifications for the Flytec V030 GPS Bait Boat:

| Feature | Specification |
|---|---|
| Item No. | V030 |
| Load Capacity | 3kg |
| Boat Size | 55*27.5*29cm |
| Motor | 550 brushless 12V motor |
| Control Distance | 800m |
| Charging Time | 4h |
| Boat Battery | 12V 20000mAh |
| Playing Time | 2-4h |
| Material | ABS |
| Color | Black |
| Boat Weight | 3606g |
| Type | Bait Thrower |
| Magnet Fishing | No |
| Origin | Mainland China |
8.1. Package Contents
Basic Version includes: Bait boat (including battery) * 1, Boat battery charging cable * 1, Remote control * 1, Remote control charging cable * 1, Eyebolt * 2, Remote control pole cap * 2, Hanging rope * 1, Spare propeller * 2, Antenna * 1, Backpack * 1
Fishfinder Version includes: Bait boat (including battery) * 1, Boat battery charging cable * 1, Remote control * 1, Remote control charging cable * 1, Eyebolt * 2, Remote control pole cap * 2, Hanging rope * 1, Spare propeller * 2, Antenna * 1, Backpack * 1, Probe * 1, Antenna * 1, Probe charging cable * 1, Fish finder display * 1, Fish finder display hanging rope * 1, Fishfinder bracket * 1, Fishfinder bracket drag rope * 1
9. User Tips
- GPS Signal Reliability: For optimal GPS performance, operate the boat in open areas with a clear view of the sky. Avoid locations with dense foliage or tall structures that can obstruct satellite signals.
- Charging Cable Care: Always handle charging cables and their connectors gently to prevent damage. Ensure they are properly aligned before plugging them in.
- Material Information: The boat is constructed from ABS material, known for its durability.
- Manual Language: This instruction manual is provided in English.
10. Warranty and Support
For any product malfunctions, technical issues, or questions not covered in this manual, please contact the seller or manufacturer for support.
A detailed user manual in PDF format is also available for download: View User Manual (PDF)