Yieryi YY-1090

Contents

Yieryi YY-1090 5-in-1 Water Quality Tester User Manual

Model: YY-1090 | Brand: Yieryi

1. Introduction

The Yieryi YY-1090 is a versatile 5-in-1 digital water quality tester designed for high-precision measurement of pH, Total Dissolved Solids (TDS), Electrical Conductivity (EC), Salinity, and Temperature. This waterproof device (IP67 rated) features a backlit LCD display for easy reading and is suitable for various applications including aquariums, pools, hydroponics, and drinking water analysis.

Yieryi YY-1090 5-in-1 Water Quality Tester showing pH, TDS, Salt, EC, and Temperature measurements.
The Yieryi YY-1090 5-in-1 Water Quality Tester, displaying its multi-parameter measurement capabilities.
Close-up of the YY-1090 tester's backlit LCD display, highlighting high accuracy, fast response, simple operation, and low power features.
Backlit display for easy reading, emphasizing high accuracy, fast response, simple operation, and low power consumption.

2. What's in the Box

Upon opening the package, you should find the following items:

  • 1 x Water Quality Tester (YY-1090)
  • 1 x User Manual
  • 1 x pH 4.00 Buffer Powder
  • 1 x pH 7.00 Buffer Powder
  • 1 x pH 10.01 Buffer Powder
Unboxing and initial overview of the Yieryi YY-1090 Water Quality Tester and its contents.

3. Specifications

Parameter Range Resolution Accuracy
Model YY-1090
pH 0.0-14.0pH 0.1pH ±0.1pH
TDS 0-9990ppm, 10.1-100.0 ppt 1ppm; 10ppm; 0.1ppt ±2% F.S
EC 0-9990µS/cm, 10.01-200.0mS/cm 1µS/cm; 10µS/cm; 0.01mS/cm ±2% F.S
Salinity 0-9990ppm, 10.1-100.0 ppt 1ppm; 10ppm; 0.1ppt ±2% F.S
Temperature 0.0°C-50.0°C; 32.0°F-122°F 0.1°C; 0.1°F ±1°C ±1.8°F
Calibration EC/TDS/SALT: 1413µS/cm; 12.88mS/cm; 111.8mS/cm calibration solution. pH: pH4.0/pH7.0/pH10.0 (Priority calibration of pH7.0 solutions).
Environment 0.0°C-50.0°C; 32.0°F-122°F
Waterproof IP67
Size 183*45*45mm
Display LCD Backlight Display
Temp. ATC 0.0°C-50.0°C; 32.0°F-122°F
Battery 4*1.5V (LR44); Low battery indicator
Automatic shut-off 5 minutes
Diagram of the YY-1090 water quality tester with dimensions, LCD display, buttons, and probe details.
Detailed diagram of the YY-1090 tester, showing its components and dimensions.

4. Setup and Installation

4.1. Battery Installation

The YY-1090 tester uses 4 x 1.5V LR44 button batteries. Ensure correct polarity when installing.

  1. Unscrew the battery protective cover at the top of the device.
  2. Remove the old batteries if present.
  3. Insert 4 new 1.5V LR44 batteries, paying attention to the positive and negative terminals.
  4. Screw the battery protective cover back on securely.
Close-up of the highly sensitive probes and the coin cell battery compartment of the YY-1090 tester.
View of the highly sensitive probes and the battery compartment, which uses 4x1.5V button batteries.

4.2. Probe Replacement

If the probe needs to be replaced due to damage or wear, follow these steps:

  1. Screw off the ring that secures the probe.
  2. Unplug the old probe from the main unit.
  3. Plug in the new probe.
  4. Screw the ring back on to secure the new probe.

Note: Replaceable electrodes have a 6-month warranty for non-human damage.

5. Operation

5.1. Basic Usage

  1. Remove the protective cap from the probe.
  2. Press the ON/OFF/HOLD button to turn on the instrument.
  3. Immerse the probe into the water sample you wish to test.
  4. Gently stir the solution and wait for the reading to stabilize on the LCD display.
  5. After use, rinse the probe with purified water and replace the protective cap.
Yieryi YY-1090 tester being used in a pool, showing pH and salinity measurements.
The YY-1090 tester in use for measuring water quality in a pool.
Yieryi YY-1090 tester measuring TDS of drinking water, with a chart indicating ideal TDS levels.
Checking the TDS value of drinking water with the YY-1090, alongside a guide for TDS levels.

5.2. Key Functions

  • Lock Reading (HOLD): Press the ON/OFF/HOLD button briefly during measurement to lock the current reading. Press again to unlock.
  • °C/°F Conversion: Press the TEMP/PH CAL button briefly to switch between Celsius (°C) and Fahrenheit (°F) temperature units.
  • Mode Conversion: Press the MODE/EC CAL button briefly to cycle through the measurement modes: TDS (ppm), Salinity (ppm), EC (µS/cm), and pH.

6. Calibration

The tester is factory calibrated and ready to use. However, recalibration may be necessary over time or if readings appear inaccurate.

6.1. pH Calibration

Always perform pH 7.00 calibration first, then pH 4.00 and pH 10.01 if needed.

  1. **Prepare pH 7.00 solution:** Pour 1 packet of pH 7.00 buffer powder into a cup, add 250ml of purified or tap water, stir, and wait 5-10 minutes for the powder to dissolve completely.
  2. Turn on the tester by pressing the ON/OFF/HOLD button.
  3. Immerse the probe into the pH 7.00 calibration solution.
  4. Press and hold the TEMP/PH CAL button until "CAL" and "7.0" start blinking 3 times on the screen. This indicates successful calibration.
  5. Rinse the probe with purified water after calibration.
  6. Repeat the process for pH 4.00 and pH 10.01 solutions if necessary, using their respective buffer powders.

6.2. EC/TDS/Salinity Calibration

Use a 12.88mS/cm calibration solution for EC/TDS/Salinity calibration.

  1. Turn on the meter and switch to EC mode by pressing the MODE/EC CAL button until "µS/cm" is displayed.
  2. Immerse the probe into the 12.88mS/cm calibration solution and stir gently.
  3. Wait for the reading to stabilize.
  4. Press and hold the MODE/EC CAL button for 5 seconds and release. "CAL" will be displayed, and a value will flash 3 times.
  5. While the value is flashing, press the MODE/EC CAL button if the flashing value is higher than 12.88mS/cm, or the TEMP/PH CAL button if the flashing value is lower than 12.88mS/cm, to adjust the displayed value to 12.88mS/cm.
  6. Release the button and wait for the reading to stop flashing. The calibration is complete.
  7. Rinse the probe with purified water and replace the protective cap.

7. Maintenance

  • **Cleaning:** After each use, always wash the electrode with purified water and keep it dry.
  • **Probe Care:** The glass electrode is fragile. Handle it gently and avoid touching the bottom or edges of containers to prevent damage.
  • **Storage:** Store the tester with the protective cap on to keep the probe moist and protected.
  • **Battery Replacement:** Replace batteries when the low battery indicator flashes on the display. Use 4 x 1.5V LR44 batteries.

8. Troubleshooting

  • **Jumping Readings:** When the test probe encounters air, it can generate resistance, causing the value to jump. This is normal. Gently stir the solution to remove air bubbles around the electrode.
  • **Inaccurate Readings:** If readings become consistently inaccurate, recalibration (see Section 6) is recommended. Ensure calibration solutions are fresh and correctly prepared.
  • **No Display/Power Issues:** Check battery installation and ensure batteries are not depleted. Replace if necessary.

9. User Tips

  • For optimal accuracy, especially with pH measurements, ensure the probe is fully immersed in the solution and gently stirred to remove any air bubbles.
  • Always use fresh calibration solutions for best results. pH buffer powders are single-use once mixed.
  • Keep the protective cap on the probe when not in use to prevent it from drying out, which can affect its lifespan and accuracy.
  • The device has an automatic shut-off feature after 5 minutes of inactivity to conserve battery life.

10. Warranty and Support

The Yieryi YY-1090 Water Quality Tester comes with a 1-year warranty for the main unit against non-artificial damage. The electrodes are considered consumables with a shelf life of 6 months, and it is recommended to replace them every 6 months for optimal performance.

For any questions or support regarding your purchase, please contact the seller or manufacturer directly.

© 2023 Yieryi. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.