Varstrom VD18MT

Contents

Varstrom VD18MT Electric Bike Display User Manual

The Future of Control at Your Fingertips

Introduction

The Varstrom VD18MT is a 1.45-inch TFT touchscreen display designed for electric bikes, offering intuitive control and robust connectivity. This manual provides detailed instructions for setting up, operating, maintaining, and troubleshooting your VD18MT display.

Varstrom VD18MT Electric Bike Display with 'Touch Screen' label
Figure 1: Varstrom VD18MT Electric Bike Display

1. Setup and Installation

1.1 Package Contents

Ensure all components are present:

  • VD18MT Display Unit
  • Mounting Bracket (integrated)
  • Connection Cable

1.2 Mounting the Display

The VD18MT display features a sleek universal mount designed to fit standard 22.2mm handlebars seamlessly. Secure the display firmly to your handlebar using the integrated bracket.

1.3 Electrical Connection

The display is compatible with 36V, 48V, and 52V battery systems. It supports Bafang CAN, Bafang UART, or Tongsheng motor protocols. It is crucial to ensure the connector of your display matches your device's protocol. Using a converter or adapter is not supported and will prevent the display from functioning normally.

Diagram showing a 5-pin female round connector for Bafang UART and a warning about connector compatibility.
Figure 2: Connector Compatibility - Ensure your device's connector matches the display's 5-pin female round connector (Bafang UART shown).

1.4 App Installation

The VD18MT pairs with the "IBike" app for advanced features like navigation, Bluetooth locking, and ride data. Search for "I-bike" in your device's app store (available for Android and iOS).

VD18MT display on handlebar with phone showing 'I-bike' app and key features: 1.45 inch screen, PAS levels, holder size, touch screen, Bluetooth.
Figure 3: VD18MT with "I-bike" App Integration

2. Operating Instructions

2.1 Power On/Off

Press and hold the power button located on the display to turn the unit on or off.

2.2 Main Interface Information

The display provides comprehensive ride data at a glance:

Diagram labeling elements of the VD18MT main display interface: Battery/Voltage, Headlight, Brake, Power value, Speed/Mileage/Riding-time, Battery indication, Error, Speed value, Speed limit sign, Power indication, Assist level.
Figure 4: Main Display Interface Overview
  • Battery/Voltage: Current battery level and voltage.
  • Headlight: Indication when headlights are active.
  • Brake: Indication when brakes are applied.
  • Power Value: Real-time power output.
  • Speed/Mileage/Riding-time: Current speed, trip distance, and ride duration.
  • Battery Indication: Graphical representation of battery charge.
  • Error: Displays error codes if issues occur.
  • Speed Value: Current riding speed.
  • Speed Limit Sign: Indicates if a speed limit is active.
  • Power Indication: General power status.
  • Assist Level: Current pedal assist level.

2.3 Touch Screen Navigation

The 1.45-inch TFT touchscreen allows for intuitive control:

  • Swipe Left/Right: Quickly switch between different display modes and settings menus.
  • Tap: Select options or confirm settings.
Diagram showing swipe gestures on the VD18MT display to switch between main interface, trip information, and settings like brightness adjustment.
Figure 5: Touch Screen Navigation and Brightness Adjustment

2.4 Physical Button Controls

In addition to the touchscreen, the display has an integrated physical button for control.

2.5 Smart Shortcuts

  • Quick 25 km/h Limit: Hold the Power and '-' buttons together.
  • Headlight Control: Long press the '+' button.
  • Walk Assist: Engage the handy 6 km/h boost mode.

2.6 Pedal Assist System (PAS)

Choose from flexible assist modes: 3, 5, 9, or a User-customizable (U) level of pedal assist.

2.7 Personalized Ride Setup

  • Visual & Interface: Switch between four main UI themes by swiping the screen. Adjust backlight across 6 levels.
  • Performance Limits: Set speed limits (10-60 km/h or 99 km/h) and choose wheel size (8", 27", 27.5", 28", 29", 700C).
  • Convenience: Set the auto-off timer (1-10 minutes or OFF).
  • Data Management: Enter settings by double-tapping the power button or swiping down to clear trip/total mileage.

2.8 Day/Night Modes

The display supports both day (no backlight) and night (backlight) states for optimal visibility.

Comparison of VD18MT display in day mode (no backlight) and night mode (backlight state).
Figure 6: Day and Night Display Modes

3. Maintenance

3.1 Cleaning

Wipe the display with a soft, damp cloth. Avoid abrasive cleaners or solvents that could damage the screen or casing.

3.2 Water and Dust Resistance

The VD18MT is rated IP67, meaning it is fully dust-tight and can withstand immersion in water up to 1 meter for a limited time. While durable, avoid prolonged submersion or high-pressure water jets.

VD18MT display with water droplets, indicating IP67 waterproof rating.
Figure 7: IP67 Waterproof Protection

3.3 Firmware Updates

The display supports Over-The-Air (OTA) firmware upgrades via the dedicated "Beken Toolset" app and a programmer. Regularly check for updates to ensure optimal performance and access to new features.

4. Troubleshooting

4.1 Display Not Powering On

  • Check all cable connections to ensure they are secure.
  • Verify that your e-bike battery is charged and providing power.
  • Confirm the display's connector type is compatible with your motor's protocol (Bafang CAN/UART or Tongsheng). Incompatible connectors or the use of adapters will prevent operation.

4.2 Lost Password Recovery

If you forget your startup password, you can recover it by performing the following sequence: press the '-' button five times, then press the '+' button once. The advanced settings password is 1919.

4.3 Incorrect Speed/Mileage Readings

Ensure the correct wheel size is set in the display's personalized ride setup (8", 27", 27.5", 28", 29", 700C).

4.4 Display Errors

If an error code appears on the display, refer to your e-bike's motor manual for specific error code interpretations, as these are often motor-specific.

5. Specifications

FeatureDetail
ModelVD18MT
Display Type1.45-inch TFT Color Touch Screen
MaterialABS+PC Composite Body
Weatherproof ProtectionIP67
Compatible Voltage36V, 48V, 52V
ProtocolBafang CAN / UART, Tongsheng
PAS Levels3, 5, 9, or User-customizable (U)
Holder SizeØ22.2mm
LanguageEnglish
ConnectivityBluetooth, "IBike" App
Light SensorYes
Dimensions (Display)27.4mm (width) x 49.3mm (height)
Cable Length440mm
Diagram showing the dimensions of the VD18MT display: 27.4mm width, 49.3mm height, 22.2mm holder diameter, and 440mm cable length.
Figure 8: VD18MT Display Dimensions

6. Warranty and Support

6.1 Warranty Period

Varstrom provides the following warranty coverage:

  • Motor & Battery: 12 months quality warranty.
  • Parts & Accessories (including display): 1 month quality warranty.
Warranty Service table showing warranty periods for E-Bike Frame (24 Months), Motor & Battery (12 Months), and Parts & Accessories (1 Month), along with conditions for under and out of warranty service.
Figure 9: Warranty Service Details

6.2 Warranty Conditions

  • Under Warranty (within 6 months from Delivery Date): All warranty costs (repair cost, material cost, shipping cost) are covered by the seller.
  • Under Warranty (6 to 12 months from Delivery Date): Repair cost and material cost are covered by the seller; shipping cost is the responsibility of the buyer.
  • Out of Warranty: After the warranty period, after-sales service is available, but all costs will be borne by the buyer. The exact cost depends on the specific issue.

6.3 Service Centers

Varstrom maintains certified service centers in Poland (PL), the United Kingdom (UK), and the USA to ensure prompt repairs and support.

7. User Tips

  • Always double-check your motor's connector type and protocol (CAN, UART, Tongsheng) before purchasing to ensure compatibility with the VD18MT display.
  • Utilize the "IBike" app for enhanced features like navigation and ride data tracking to get the most out of your display.
  • Familiarize yourself with the quick shortcuts (25 km/h limit, headlight control, walk assist) for convenient on-the-go adjustments.
  • Regularly check for firmware updates using the "Beken Toolset" app to keep your display optimized and secure.
  • If you customize your startup password, make a note of it. The recovery sequence (- x5 then + x1) is a last resort.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.