Introduction
Thank you for purchasing this Hobbywing product. The X8 integrated power system is designed for agricultural drones, capable of carrying a load of 5-7kg per rotor. It features an optimized PMSM algorithm based on FOC (Field Oriented Control) for a perfect power system, ensuring high stability, reliability, and efficiency. The system is IPX6 waterproof and includes drainage channels, making it suitable for harsh environments. It also incorporates intelligent multiple redundant protection functions and real-time operating data output.

Setup and Installation
The X8 power system is designed for easy installation on agricultural drones. Ensure all components are securely mounted and wired correctly.
Component Overview

The image above illustrates the installation process and component composition. The whole power system has been assembled before leaving the factory. It is ready to use and can be directly mounted on your agricultural drone as per the rotation direction (CW/CCW) marked on the motor.
Wiring Diagram

Ensure the power lines (12AWG, red for positive, black for negative) and the signal wire (JR-3P) are connected correctly. The blue/red/white in-color cable is for updating ESC firmware. The white/black in-color cable is the throttle signal cable, and the yellow wire is the RPM signal output wire.
Operating Instructions
LED Display Light
The X8 integrated power system features a high-brightness LED display light. This light indicates the working status of the power system and can issue early warning signals if an abnormality occurs, enhancing safety.

You can set the light color or turn off the display light. To change the light color, unscrew the two M3*8 screws for fastening the light cover with a screw driver, slice the DIP switches according to the table below to change the LED color (it's Green by default). Mount the cover back after setting.
| DIP Switch 1 | DIP Switch 2 | DIP Switch 3 | Color of the LED |
|---|---|---|---|
| ON | ON | ON | WHITE |
| ON | ON | OFF | Light Blue |
| ON | OFF | ON | Purple |
| ON | OFF | OFF | Yellow |
| OFF | ON | ON | Green |
| OFF | ON | OFF | Red |
| OFF | OFF | ON | LED Disabled |
Protection Functions
The X8 power system is equipped with several protection functions to ensure safe operation:
- Power-on Self-test: The system performs a self-test upon power-on.
- Power-on Voltage Abnormal Protection: Protects against incorrect voltage during startup.
- Current Protection: Monitors and protects against excessive current.
- Stall Protection: Prevents damage if the motor stalls.
The system can output operating status data to the flight controller in real-time, including input throttle amount, response throttle volume, motor speed, bus voltage, bus current, phase current, capacitor temperature, and MOS tube temperature. This data helps improve flight performance and efficiency, and overall system reliability.
Note: Using the Hobbywing Data Link data acquisition memory (purchased separately) can simultaneously collect real-time operation data of the 8-channel power system and pass it to the flight controller through the bus interface to form a closed-loop control system.

Maintenance and Care
General Maintenance
- Always keep your drone away from crowd, high-voltage power lines, and obstacles. Fly your drone in accordance with relevant safety regulations.
- Never get close to the (high-speed rotating) propeller & motor, otherwise you may get hurt.
- Check if all the parts are in good condition before use. If there exists any damaged part, please contact the factory for replacement.
- Check if any screw for connecting the parts is loose and the motors are horizontal before each flight.
- The bore diameter of the arm for the X8 power system is 40mm.
- You can change the light color of the LED light. In that case, you need to disassemble the light cover and slide the DIP switches accordingly.
- You can rinse the motor with fresh water after each flight to keep it clean.
Propeller Replacement
Unscrew the two M3*10 screws for fastening the blades with a screw driver and change the blades. If you also want to change the propeller adapter, then you need to unscrew the four M3*10 screws for fixing the adapter with another screw driver and change the whole set of propeller.
When mounting the propeller, you need to mount the bottom cover (of the propeller adapter) on the motor first, then blades, spacers and the top cover (of the propeller adapter), and then fix them with screws. Please note that the blades can rotate freely after fastening them with M3 screws, and ensure that you will also apply some glue to the screws after fastening the propeller adapter to the motor with M3 screws.

Environmental Protection
The X8 powertrain is IPX6 waterproof rated and has drainage channels for liquids and debris. It is able to operate in harsh environments such as rain, pesticide salt spray, high temperature, sand, and dust. You can rinse it with water directly after usage without any problem.

Troubleshooting and Warning Tones
This section provides solutions for common issues indicated by warning tones.
| Trouble | Warning Tones | Possible Cause | Solution |
|---|---|---|---|
| The ESC was unable to start the motor. | "888..." a single beep that repeats rapidly. | The throttle stick was not moved to the bottom position. | Move the throttle stick to the bottom position. |
| The ESC was unable to start the motor. | "B, B, B..." a single beep that repeats (the time interval is 1 second). | There was no throttle signal output from the TH channel on the receiver. | Check if the transmitter & receiver are well bound, check if the throttle control cable has been properly plugged into the TH channel. |
| The power-on voltage was 18V. | "BB, BB..." a double beep that repeats (the time interval is 1 second). | The battery voltage was too low. | Change a suitable and fully charged battery. |
| The power-on voltage was above 55V. | "BBB, BBB..." a triple beep that repeats (the time interval is 1 second). | The battery voltage was too high. | Change a suitable and fully charged battery. |
Explanations for Protections
- Start-up Protection: The ESC will shut down the motor if it fails to start the motor normally within 2 seconds by increasing the throttle input. In this case, you need to move the throttle stick back to the bottom position and restart the motor. Possible causes of this problem are poor connection/disconnection between the ESC and motor, wires are improperly blocked, etc.
- Motor Lock-up Protection: The ESC will cut off its output to the motor immediately and won't try to restart the motor when it detects the motor is locked up. In this condition, you need to pull the throttle stick to the bottom position first and then push it upward to clear the error and restart the ESC to resume the output.
- Over-current Protection: The ESC will cut off its output immediately when the peak current gets close to 300A. It only restarts after you power it off and then back on.
- Throttle Signal Loss Protection: When the ESC detects loss of signal for over 0.25 seconds, it will cut off the output immediately to avoid an even greater loss which may be caused by the continuous high-speed rotation of propellers. The ESC will resume the corresponding output after normal signals are received.
Specifications
General Parameters
- Model Number: Hobbywing X8
- RC Parts & Accs: Motor Components
- Material: Composite Material
- Recommend Age: 14+y
- Use: Vehicles & Remote Control Toys
- Is Electric: No Battery
- Is it battery/power supply: N
- Is it charger/adapter: N
- Is Batteries Included: No
- High-concerned chemical: None
Performance and Physical Specifications
| Feature | Specification |
|---|---|
| Max thrust | 15kg |
| Recommended takeoff weight per axis | 5-7kg |
| Lithium compatible | 12S (Up to 52.2V) |
| Tube outer diameter | 40mm |
| Ingress Protection | IPX6 |
| ESC Model | XRotor 80A-FOC |
| Motor Model | 8120-100KV |
| Propeller | 3011 propeller |
| Operating Temperature | -20°C to 50°C |
| Total Combo Weight | 1150g |
| Throttle Range | 1100-1940μs |
Advanced Parameters (30 Inch Propeller)
| Voltage (V) | Throttle (%) | Thrust (g) | Current (A) | Power (W) | Efficiency (g/W) |
|---|---|---|---|---|---|
| 46V (12S Lipo) | 40% | 2001 | 6.5 | 207.3 | 12.3 |
| 50% | 3999 | 8.7 | 399.4 | 10.0 | |
| 54% | 5011 | 10.5 | 484.7 | 10.3 | |
| 57% | 5988 | 11.7 | 536.7 | 9.3 | |
| 60% | 7013 | 14.2 | 653.3 | 9.1 | |
| 64% | 7988 | 17.1 | 787.8 | 8.7 | |
| 66% | 9019 | 18.7 | 862.9 | 8.4 | |
| 70V (17S Lipo) | 70% | 9990 | 22.4 | 1031.0 | 8.0 |
| 74% | 11017 | 26.6 | 1225.0 | 7.5 | |
| 80% | 12005 | 33.9 | 1563.2 | 6.9 | |
| 90% | 13991 | 47.1 | 2169.4 | 6.2 | |
| 100% | 15289 | 54.0 | 2486.9 | 5.9 |
User Tips
- For optimal performance, ensure propellers are balanced and free from damage before each flight.
- Regularly check all connections and screws for tightness to prevent unexpected disconnections during operation.
- Utilize the real-time data output feature with the Hobbywing Data Link for advanced monitoring and system optimization.
Warranty and Support
Please contact Hobbywing for after-sales service if the power system is damaged or if you encounter any issues that cannot be resolved using the troubleshooting guide. You can replace damaged parts with replacements included in the product box. If the damage occurred during operation and you are not satisfied with the customer service, please contact Hobbywing for repair. Improper repair may cause serious damage.