CNC CNC X We Plus

Contents

CNC X We Plus Wireless Tattoo Pen Rotary Tattoo Machine User Manual

Model: CNC X We Plus (Product ID: TM-001)

1. Introduction

This manual provides essential information for the safe and effective use of your CNC X We Plus Wireless Tattoo Pen Rotary Tattoo Machine. Please read all instructions carefully before use to ensure proper operation and to prevent damage or injury.

The CNC X We Plus is a professional wireless tattoo machine designed for precision and ease of use, featuring a dual control system and advanced power management.

2. Safety & Warnings

Important Safety Information

Read all instructions before use. Failure to follow these instructions may result in damage to the product, skin injury, infection, or other personal injury.

General Safety Information:

  • This product is for professional use only and not for children's play.
  • Keep the tattoo machine, needles, power supply, and all accessories out of reach of children under 12 years old.
  • Keep away from children and pets at all times during use, and no unsupervised use by minors or untrained personnel.
  • Do not use this product for purposes other than its intended use (tattooing on human skin); do not use for animal marking, material engraving, or other non-skin tattooing applications.
  • Inspect the product, including the machine body, needle bar, power cord, and connection parts before each use. Do not use if damaged, deformed, loose, or malfunctioning.
  • Follow professional installation and operation guidelines strictly to avoid needle stick injuries, excessive skin puncture, or other bodily harm.
  • Do not expose the tattoo machine body, power supply, or control panel to water, moisture, direct sunlight, or high humidity environments to prevent short circuit, electric shock, or product damage.
  • Handle tattoo needles, needle bars, and other sharp accessories with extreme care to avoid cuts, needle stick injuries, or cross-infection.
  • Disinfect the tattoo machine's contact parts and accessories thoroughly before and after each use in accordance with professional disinfection standards to prevent cross-infection of bacteria and viruses.
  • Do not operate the tattoo machine with wet hands to avoid electric shock risk.
  • Stop using the machine immediately if abnormal noise, overheating, or needle jamming occurs. Cut off the power supply and check the fault before reusing.
  • Novice users must receive systematic professional training before use.
  • Do not use the tattoo machine on damaged, inflamed, allergic, or sensitive skin to avoid aggravating skin damage.

Warning on Accessories:

Use only original and certified matching accessories (neeedles, power supply, grip) provided by the manufacturer. Non-matching accessories may cause machine failure, skin injury, or fire hazard.

3. Product Components & Features

The CNC X We Plus package includes the main tattoo machine, two battery barrels, two stroke discs (3.0mm and 4.0mm), a manual, and a Type-C charging cord.

CNC X We Plus Wireless Tattoo Pen with battery, wireless pedal, and stroke discs

Figure 1: CNC X We Plus Wireless Tattoo Pen and accessories.

Contents of the CNC X We Plus package

Figure 2: Package contents including machine, batteries, stroke discs, and charging cable.

Key Features:

  • **Wireless Module:** Features 2.4G Signal Stability, Low Energy Consumption, and Smart AI.
  • **Soft Drive:** Provides 3.0mm and 4.0mm stroke options for versatile tattooing.
  • **New Power:** Equipped with an LCD Digital Display, larger 1000mAh capacity, Magnetic Suction Connection, and 2.4G wireless signal module. Output voltage adjustable in 0.1V units.
Wireless Module features: 2.4G Signal Stability, Low Energy Consumption, Smart AI

Figure 3: Wireless Module capabilities.

Soft Drive mechanism with 3.0mm and 4.0mm stroke discs

Figure 4: Soft Drive system with interchangeable stroke discs.

New Power features: LCD Digital Display, 1000mAh Capacity, Magnetic Suction Connection, 2.4G wireless signal module, +/-0.1V output voltage

Figure 5: New Power battery features and display.

4. Specifications

Table of Pedal and WE Plus parameters

Figure 6: Detailed parameters for the Wireless Pedal and WE Plus Tattoo Machine.

WE Plus Tattoo Machine Parameters:

FeatureSpecification
Stroke3.0mm, 3.5mm, 4.0mm
Grip Diameter31.5mm
Machine Length153mm
Machine Weight188g
MaterialAluminum
Needle Depth0-4.0mm
Battery Capacity1000mAh
Voltage Output5V-12V
Adjustment Unit0.1V
Wireless PedalSupport
Charging PortType-C
MotorX-11 Motor
DriveSoft drive

Wireless Pedal Parameters:

FeatureSpecification
Size55 × 25 × 104 (mm)
Weight80g
Built-in Battery Capacity500mAh
Charging PortType-C
Charging Specifications5.0V ~ 2000mA
Charging Time1 hour

General Product Specifications:

FeatureSpecification
Voltage220 V
Batteries IncludedYes
High-concerned chemicalNone
Gun TypeElectric
Commodity Quality CertificationCE
OriginMainland China
TypeTattoo Gun
Number of PiecesOne Unit
ColorBlack (Gold variant shown in some images)
Rated power4.8W
Needle stroke3.5 MM (Adjustable 0.8-4.0mm)
Needle length0-4.0 MM
Starting voltage12V, 7V

5. Setup & Assembly

5.1 Before First Use:

Remove all protective films and packaging materials from the tattoo machine body, grip, and power supply. Disassemble the detachable parts (grip, needle bar) and perform high-temperature and high-pressure disinfection or professional disposable disinfection treatment in accordance with medical disinfection standards. Ensure all parts are dry before assembly.

5.2 Accessory Assembly:

  1. Insert the sterilized tattoo needle into the needle bar, and fix it tightly with the locking nut to prevent the needle from loosening during operation.
  2. Connect the assembled needle bar to the tattoo machine body, adjust the needle stroke (0.8-4.0mm adjustable) according to the tattooing needs (lining/shading), and lock the adjustment knob.
  3. Screw the disinfected grip onto the machine body to ensure a firm connection without looseness.

5.3 Power Connection:

Connect the DC power cord of the tattoo machine to the matching certified power supply (input: 100-240V AC, 50/60Hz; output: 0-18V DC). Plug the power supply into a grounded power socket, and ensure the power switch is in the "OFF" position before connection.

5.4 Parameter Adjustment:

Turn on the power supply switch. Adjust the voltage according to the tattooing demand:

  • **Lining:** Recommended to set 6-10V.
  • **Shading:** Recommended to set 4-8V.

Test the machine's running state by pressing the foot pedal, adjust the needle speed and stroke to the appropriate state, and ensure the needle does not jam or shake abnormally.

Video 1: Unboxing and initial assembly of the CNC X We Plus Tattoo Machine.

6. Operating Instructions

  1. Hold the tattoo machine grip with a firm and comfortable grip, keeping the machine at a 15-45° angle to the skin surface during tattooing.
  2. Control the machine by stepping on the foot pedal (foot pedal control is the default mode). Release the foot pedal to stop the machine running.
  3. Avoid long-time continuous operation to prevent machine overheating.
  4. Move the machine evenly and slowly on the skin. Do not stay in the same position for a long time to avoid excessive skin puncture and blistering.

7. Maintenance

7.1 After Use:

  1. Step on the foot pedal to stop the machine, turn off the power supply switch, and unplug the power cord from the socket in sequence.
  2. Disassemble the used needle and dispose of it in a sealed sharp object container in accordance with medical waste disposal standards (do not reuse disposable needles).
  3. Disassemble the grip, needle bar, and other detachable parts, and perform disinfection and cleaning treatment immediately.
  4. Wipe the machine body and power supply with a dry, alcohol-disinfected soft cloth to remove ink and dirt (do not use water or detergent to clean directly).

7.2 Storage:

After cleaning and disinfection, dry all parts completely. Assemble the machine body (without needle) and store it in a dry, cool, dust-free storage box. Store the power supply, unused sterilized needles, and accessories in a sealed container separately, and keep away from high temperature, moisture, and direct sunlight.

7.3 Routine Maintenance:

Lubricate the machine's bearing and moving parts with special lubricating oil every 50 hours of use to ensure smooth operation. Check the power cord for wear and tear regularly, and replace it immediately if damaged.

8. User Tips

Professional tattoo artists can adjust the voltage, needle stroke, and running speed according to their operating habits and tattooing needs on the premise of complying with safety operation standards.

9. Troubleshooting

If the machine experiences abnormal noise, overheating, or needle jamming, stop use immediately. Disconnect power, inspect the machine for any visible issues, and consult the manufacturer's support if the problem persists after basic checks.

10. Compliance & Support

Compliance Information:

This tattoo machine complies with EU CE marking requirements (EU Regulation (EC) No 1935/2004, EU Regulation (EU) 2017/745, EN 61000-6-1, EN 61000-6-3), RoHS Directive 2011/65/EU, and for the US market, FDA 21 CFR Part 878.4000 and UL 60950-1 electrical safety standards. All materials meet skin contact safety requirements and are free of harmful heavy metals and allergens.

Note: This product must comply with all applicable safety and regulatory requirements in the market where it is sold. Sellers must assess which requirements and regulations apply based on the actual product type, function, and destination market.

Manufacturer & EU Representative Information:

Manufacturer: Tattoo Tech Co., Ltd, No. 88 Hi-Tech Industrial Park, City A, Province B, China
Email: info@tattootech.com
Website: www.tattootech.com
Telephone: +86-XXX-XXXXXXX

EU Authorized Representative: EU AR Service GmbH, Hauptstraße 100, 10178 Berlin, Germany
Email: eu-rep@tattooservice.eu
Website: www.tattooservice.eu
Telephone: +49-30-XXXXXXX

Importer: European Tattoo Supply Co., Rue de la Commerce 50, 75001 Paris, France

Additional Resources:

A user manual in PDF format is available for download. You can access it via the official product page or by contacting support.

VIP User Service Mailbox: SUPPORT@CNCTAT.COM

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.