1. Overview
The LAUNCH CRP123X V2.0 is a well-designed car scanner equipped with essential features for both home mechanics and professionals. It offers comprehensive diagnostic capabilities for four main vehicle systems and includes various reset services.
1.1 Key Features
- Four System Diagnosis: Engine, Transmission, ABS (Anti-lock Braking System), and SRS (Supplemental Restraint System).
- 7 Free Reset Services: Including ETS (Electronic Throttle System) Reset, Oil Reset, SAS (Steering Angle Sensor) Reset, ABS Bleeding, BMS (Battery Management System) Reset, Brake Reset, and DPF (Diesel Particulate Filter) Reset.
- Lifetime Free Update: Via Wi-Fi connection.
- AutoVIN Service: Quickly identifies vehicle information.
- Battery Voltage Testing and Graphing.
- Multi-Language Support: 9 languages available.
- Wide Vehicle Compatibility: Supports over 57 car brands and 10,000+ vehicle models, covering OBD2/EOBD/JOBD vehicles from 1996 and newer.

1.2 Vehicle Coverage
This diagnostic tool is specifically designed to work with all OBD II compliant vehicles, including those with Controller Area Network (CAN). To verify if a 1994 or 1995 vehicle is OBD II compliant, check the Vehicle Emissions Control Information (VECI) Label, usually located under the hood or by the radiator. The label should designate "OBD II Certified". Government regulations mandate that all OBD II compliant vehicles must have a standard 16-pin Data Link Connector (DLC).

1.3 OBD II Definitions
The OBD II system monitors emission control systems and key engine components. Key terms include:
- EOBD: European On-Board Diagnostics, similar to OBD II.
- Communication Protocols: Methods for vehicle systems to communicate (CAN Bus, J1850 VPW, ISO 9141-2, J1850 PWM, ISO 14230 KWP).
- PCM (Powertrain Control Module): The vehicle's on-board computer.
- DLC (Data Link Connector): The 16-cavity connector for diagnostic tools.
- MIL (Malfunction Indicator Light): The "Check Engine" warning light.
- DTC (Diagnostic Trouble Code): A code stored in the computer indicating a fault.
- Freeze Frame Data: Operating conditions recorded when a DTC is stored.
- PID (Parameter Identification Data): Data returned by control modules.
- Monitors: Diagnostic routines in the PCM for testing systems.
- Enabling Criteria: Conditions required for monitors to run.
- Trip: A drive cycle meeting enabling criteria for a specific monitor.
- Warm-up Cycle: Vehicle operation after engine off, reaching specific temperatures.
- Fuel Trim (FT): Adjustments to the base fuel schedule.
1.4 Diagnostic Trouble Codes (DTCs)
DTCs are five-digit alphanumeric codes that identify problem areas. They consist of:
- 1st character: Letter (B, C, P, U) for the main system (Body, Chassis, Powertrain, Network).
- 2nd character: Numeric digit (0-3) for code type (Generic or Manufacturer-Specific).
- 3rd character: Letter or numeric digit (0-9, A-F) for the specific system or sub-system.
- 4th and 5th characters: Letters or numeric digits (0-9, A-F) for the malfunctioning section.
Caution: Do not replace parts based solely on DTCs. Always consult the vehicle's service manual for proper testing procedures.
2. Product Description
2.1 Components & Controls
The CRP123X V2.0 features a user-friendly interface with a 5-inch touch screen and physical buttons for navigation.

- Charging LED: Red indicates charging, Green indicates fully charged.
- LCD: Displays test results and menu options.
- USB Type-C port: For connecting the charging cable.
- DB-15 Diagnostic Connector: Connects to the vehicle's DLC.
- Power Button: Turns the tool on/off.
- HOME Button: Navigates to the Job Menu screen.
- Selection Buttons: Up/Down arrows for selection, Left/Right arrows for selection or page navigation.
- OK Button: Confirms a selection or action.
- Return Button: Exits the current program or returns to the previous screen.
2.2 Technical Specifications
| Feature | Specification |
|---|---|
| Screen | 5" Touch Screen |
| Battery Capacity | 6100mAh |
| Operating System | Android 8.1 |
| RAM | 2 GB |
| ROM (Storage) | 32 GB (system displays 25.9GB) |
| OBDII Input Voltage Range | 9~18V |
| Charging via | DC 5V 2A charging cable or Diagnostic cable through vehicle's DLC |
| Diagnostic Cable Length | 1.2M |
| Dimensions | 228 mm x 125 mm x 34 mm (approx. 7.48 x 4.21 x 0.98 inches) |
| Operating Temperature | 0°C to 50°C (32°F to 122°F) |
| Storage Temperature | -20°C to 70°C (-4°F to 158°F) |
| Charging Temperature | 0°C to 40°C (32°F to 104°F) |
Note: The operating temperature refers to the temperature at which the scan tool works normally in non-charging status.

2.3 Packing List
The following items are typically included in the package:
- Diagnostic tool x 1
- OBD II diagnostic cable x 1
- Charging cable x 1
- User manual x 1
- Carrying bag x 1
3. Initial Use and Setup
3.1 Charging the Tool
There are two methods to charge your CRP123X V2.0:
- Via Charging Cable: Plug one end of the included charging cable into the Type-C port of the tool and the other end into an external power supply.
- Via Diagnostic Cable: Insert one end of the diagnostic cable into the DB-15 connector of the tool and the other end into the vehicle's DLC.
The charging LED will illuminate solid green when the battery is fully charged.
3.2 Getting Started
For first-time use, you need to perform some system settings:
- Press the power button to turn the tool on.
- The screen will display a welcome page. Tap Start.
- Choose your desired system language and tap Next step.
- Choose the desired time zone and tap Next step to enter the WLAN setup screen.
- Slide the Wi-Fi switch to ON. The system will search for available wireless LANs. Select your desired network. If the network is encrypted, enter the password.
- After connecting to Wi-Fi, tap Next step to configure workshop information (optional).
- Read the user agreement, check the box before Agree to all the above terms, and tap OK to finish the sign-up process and navigate to the Job Menu.
3.3 Job Menu Overview
The main menu screen provides access to various function modules:
- Local Diagnose: Configures the tool for professional diagnostics.
- Service Function: Offers coding, reset, relearn, and other service functions.
- Other Modules: Includes add-on modules to extend functionality.
- Upgrade: Updates vehicle diagnostic software and APK.
- Mall: Subscribe to extra diagnostic or reset software.
- Know Your Customer: Assists repair shops with business analysis.
- Mine: Check saved reports, order information, and system settings.
- Toolbox: Access battery voltage, diagnostic software clear, firmware fix, DTC library, diagnostic record, DLC lookup, feedback, image, and product manual.
4. Operation
4.1 Vehicle Connection
- Turn the vehicle ignition off.
- Locate the vehicle's 16-pin Data Link Connector (DLC). Refer to the vehicle's service manual if needed.
- Plug one end of the diagnostic cable into the vehicle's DLC port and the other end into the DB-15 diagnostic connector of the tool. Tighten the captive screws.
- Turn the vehicle ignition on. The engine can be off or running.
Caution: Do not connect or disconnect any test equipment while the ignition is on or the engine is running.

4.2 System Diagnostics
This function diagnoses electronic control systems of a single vehicle model. Supported systems and functions vary by product configuration.
4.2.1 Smart Diagnosis (Auto-Detect)
This feature quickly accesses vehicle electronic control systems by decoding the VIN. To enable, go to Mine > Settings and set Automatic detection on connect to On. After connection, turn the ignition on, and the system will auto-detect. If the VIN is successfully obtained, confirm and tap OK to start diagnosing. A diagnostic report will be automatically generated.
Alternatively, you can tap Local Diagnose > AutoDetect to start manually if auto-detection is off.
Note: A stable network connection is recommended for successful VIN access. Not all cars support Auto-Detect.
4.2.2 Manual Diagnosis
If Auto-Detect fails, you can manually input the VIN or select the vehicle model and year from a menu-driven command. Ensure the corresponding vehicle manufacturer software is installed.
4.3 OBDII Diagnostics (Full 10 Modes)
This option provides a quick way to check for DTCs, isolate MIL causes, check monitor status for emissions testing, and verify repairs. After connecting the tool, tap OBD II on the Local Diagnose screen. The tool will automatically establish a communication link.

- Read I/M Readiness: Checks if emissions-related systems are operating properly and ready for inspection/maintenance testing.
- Read Live Data: Retrieves and displays real-time data and parameters from the vehicle's ECU. This can be viewed in values, waveform graphs, or combined graphs for easier comparison.
- Read Freeze Frame: Captures a snapshot of operating conditions when an emission-related fault occurs.
- Read Fault Code: Displays detailed information of DTC records.
- Clear Fault Code: Erases codes from the vehicle after repairs. Ensure ignition is ON and engine is OFF. Clearing codes does not fix the underlying problem.
- Test Results: On-Board Monitoring Test: Retrieves test results for non-continuously monitored emission-related powertrain components.
- Control Operation of On-Board Component/System: Accesses vehicle-specific subsystem and component tests.
- Read Vehicle Information: Retrieves VIN, Calibration ID (CID), and Calibration Verification Number (CVN).
- EU OBFCM: Monitors fuel and energy consumption data for CO2 emissions compliance.
- Component Test: Actuates certain vehicle components via commands from the scanner to test their operability.
4.4 Service Functions
The tool offers various service functions to restore vehicles to functional status after repair or replacement. These include coding, reset, and relearn procedures. Available functions may vary by vehicle manufacturer, year, and model.

7 Free Reset Services:
- RESET ETS (Electronic Throttle System)
- RESET OIL (Oil Lamp Reset)
- RESET SAS (Steering Angle Sensor Calibration)
- RESET BLEED (ABS Brake Bleeding)
- RESET BMS (Battery Management System Reset)
- RESET BRAKE (Electronic Parking Brake Reset)
- RESET DPF (Diesel Particulate Filter Regeneration)
19 Optional Reset Services (Available for purchase in the Mall):
- Reset Brake
- Reset Gear
- Reset IMMO (Immobilizer Matching)
- Reset Injec (Injector Coding)
- Reset TPMS (Tire Pressure Monitor System Reset)
- Reset BMS (Battery Management System Reset)
- Reset Bleed (ABS Brake Bleeding)
- RESET DPF (Diesel Particulate Filter Regeneration)
- SUS Reset (Suspension Reset)
- AFS Reset (Adaptive Front-lighting System Reset)
- SUN ROOF (Sunroof Initialization)
- Gearbox Learn (Gear Learning)
- EGR Adaption (EGR System Adaptation)
- A/C Relearn (Air Conditioning System Relearn)
- Intelligent Cruise Control
- Engine Power Balance Monitoring
- Motor Angle Calibration
- High Voltage Battery Diagnostics
- GPF Regeneration (Gasoline Particulate Filter)
To perform a reset, select Service Function from the Job Menu, choose the desired service function, select the car brand, and then the reset mode. Follow the on-screen instructions.
4.5 Toolbox Functions
The Toolbox provides access to several utility functions:
- Battery Voltage: Measures the vehicle's current battery voltage.
- Diagnostic Software Clear: Deletes infrequently used diagnostic software.
- Firmware Fix: Upgrades and fixes diagnostic firmware. Do not interrupt power during this process.
- DTC Library: Retrieves detailed descriptions of DTCs from the database.
- Diagnostic Record: Stores running parameters or waveform graphs.
- DLC (Data Link Connector) Location: Helps find the DLC in various vehicles.
- Feedback: Allows users to send diagnostic problems for analysis and troubleshooting.
- FAQ: Lists frequently asked questions and answers.
- Image: Manages and shares screenshots.
- Product Manual: A detailed operation manual is integrated into the tool for quick reference.

5. Maintenance
5.1 Software Upgrade
To ensure optimal performance and access to the latest features, regularly update the diagnostic software and APK. A numeric indicator on the Upgrade module in the Job Menu will signal available updates. Tap Upgrade to enter the update center. You can select specific software or update all. A stable network connection is required.
5.2 Clean Up
This option allows you to clear cache files and free up storage space on the device.
6. Troubleshooting
6.1 Diagnostic Trouble Codes (DTCs)
If a DTC is displayed, use the DTC Library function to retrieve its detailed description. Remember that DTCs only indicate a problem area; further diagnosis using the vehicle's service manual is often required to pinpoint the exact cause. Clearing DTCs without addressing the underlying issue will result in the codes reappearing.
6.2 Feedback and FAQ
If you encounter diagnostic problems that you cannot resolve, use the Feedback module to send details to LAUNCH for further analysis. The FAQ section in the Toolbox also provides answers to common questions.
7. User Tips
- Keep Software Updated: Regularly check for and install software updates via Wi-Fi to ensure compatibility with newer vehicles and access to the latest diagnostic features.
- Review Live Data: When diagnosing intermittent issues, utilize the live data stream function and record the data. This can help identify anomalies that might not trigger a DTC immediately.
- Understand DTCs: Don't just clear codes. Always investigate the meaning of a DTC using the built-in library or external resources to understand the potential problem before attempting repairs.
- Battery Check: Use the battery voltage test function to quickly assess the vehicle's battery health, as a weak battery can sometimes cause various electrical issues.
- Utilize AutoVIN: For quick vehicle identification, ensure the AutoVIN feature is enabled in settings. If it fails, manually input the VIN.
8. Safety Precautions and Warnings
To prevent personal injury or damage to vehicles and/or the tool, always observe the following safety precautions:
- The tool contains an internal Lithium Polymer battery. Do not disassemble, crush, pierce, or dispose of the battery in fire or water to avoid fire or explosion.
- This product is not a toy; keep it away from children.
- Do not expose the device to rain or wet conditions.
- Do not place the device on any unstable surface.
- Never leave the device unattended during charging. Place it on a non-flammable surface.
- Handle the device with care. If dropped, check for damage before further use.
- Do not operate the tool in explosive atmospheres (flammable liquids, gases, heavy dust).
- Keep the tool dry, clean, and free of oil, water, or grease. Clean with a mild detergent on a clean cloth.
- Individuals with pacemakers should consult their physician before use, as electromagnetic fields may cause interference.
- Always perform automotive testing in a safe environment.
- Do not operate or observe the tool while driving a vehicle to avoid driver distraction and accidents.
- Wear safety eye protection that meets ANSI standards.
- Keep clothing, hair, hands, tools, and other objects away from moving or hot engine parts.
- Operate the vehicle in a well-ventilated work area. Exhaust gases are poisonous.
- Chock the drive wheels and never leave the vehicle unattended while running tests.
- Use extreme caution around ignition coil, distributor cap, ignition wires, and spark plugs, as these components create hazardous voltages when the engine is running.
- Put the transmission in P (for A/T) or N (for M/T) and ensure the parking brake is engaged.
- Keep a fire extinguisher suitable for gasoline/chemical/electrical fires nearby.
- Do not connect or disconnect any test equipment while the ignition is on or the engine is running.
9. Compliance Information
FCC ID: XUJCRP123XV3
IC: 29886-C123XV3
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This device complies with Innovation, Science and Economic Development Canada's licence-exempt RSSs and part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference; and (2) This device must accept any interference received, including interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.
The device for operation in the band 5150-5250MHz is only for indoor use.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference, try to correct it by reorienting or relocating the receiving antenna, increasing separation between equipment and receiver, connecting equipment to a different circuit, or consulting a dealer/technician.
9.1 Specific Absorption Rate (SAR) Information
This product meets government requirements for exposure to radio waves. The SAR limit is 1.6 W/kg averaged over one gram of tissue. This device was tested for typical body-worn operations 0mm from the body. To maintain compliance with RF exposure requirements, use accessories that maintain a 0mm separation distance between the user's body. Third-party belt-clips, holsters, and similar accessories should not contain metallic components. Use only the supplied or an approved antenna.
10. Warranty and Support
10.1 Warranty
LAUNCH electronic products are warranted against defects in materials and workmanship for one year (12 months) from the date of delivery to the user. This warranty does not cover parts that have been abused, altered, used for unintended purposes, or used inconsistently with instructions. The exclusive remedy for a defective automotive meter is repair or replacement. LAUNCH is not liable for consequential or incidental damages.
Final determination of defects is made by LAUNCH. No agent, employee, or representative of LAUNCH has authority to bind LAUNCH to any affirmation, representation, or warranty concerning LAUNCH automotive meters, except as stated herein.
10.2 Customer Service
If you have any questions regarding the operation of the unit, contact the seller or LAUNCH TECH Service Center:
- Website: https://en.cnlaunch.com
- Phone: +86 755 8455 7891
- Email: overseas.service@cnlaunch.com