NYXI Hyperion 3 Wireless JoyPad for Switch 2

Introduction

Dear Gamer,

Thank you for purchasing our product. Before you use the product, please read this product manual carefully to ensure optimal performance and longevity of your NYXI Hyperion 3 Wireless JoyPad.

The NYXI Hyperion 3 is the world's first third-party magnetic Joy-Con for the Nintendo Switch 2, designed to enhance your gaming experience with advanced features and ergonomic design.

Package Contents

Please check the package contents to ensure all items are present:

• 1 × Left Controller
• 1 × Right Controller
• 1 × Rechargeable Center Bridge
• 1 × Replaceable D-pad
• 1 × USB-C Charging Cable (1M)
• 1 × Product User Manual (with Warranty Card)

Specifications

Game Controller Technical Parameters (Model: NS-202, Code: NJ22)

Center Bridge Technical Parameters

Key Features Overview

Setup

Compatibility

The NYXI Hyperion 3 JoyPad supports the Nintendo Switch 2 host system, version 20.0 and above.

Wired Connection

To connect the controllers via wired mode:

1. Align the left controller's '-' key and the right controller's '+' key upwards.
2. Magnetically attach them to the corresponding magnetic ports on both sides of the console.
3. The console will indicate a successful match with a connection animation on both sides.

Bluetooth Connection (Wireless Mode)

1. Power on the Switch 2 console.
2. On the main interface, tap the controller icon with your finger, then select the "Change Grip/Order" screen.
3. Press and hold the SYNC button on the left (or right) controller for 3 seconds until the RGB indicator flashes rapidly, indicating Bluetooth pairing mode.
4. The console will automatically search for and pair with the controller.
5. After successful connection, the controllers' RGB indicators will display solid lights in the following channel colors:
• Channel 1: Solid Orange
• Channel 2: Solid Green
• Channel 3: Solid Blue
• Channel 4: Solid Purple

Keylinker App Connection

The Keylinker App allows for controller customization and firmware upgrades.

1. Use a mobile browser to scan the QR code below or search for "KeyLinker" in your app store to download and install.
2. After installation, grant any requested permissions.
3. Connect your phone's Bluetooth in Android/iOS mode, find the device named "NyXI Nj22", and tap to pair.
4. After successful connection, tap the settings button next to the device name to enter the controller customization interface.

Operating Instructions

Controller Layout

Left Controller:

• - Button
• L Button
• Left Joystick (TMR Hall Joystick)
• D-Pad (Replaceable)
• Screenshot Button
• T Button (Turbo)

Right Controller:

• + Button
• R Button
• BAXY Buttons (Mechanical Micro-Switch)
• Right Joystick (TMR Hall Joystick)
• HOME Button
• C Button (Native C-button for one-touch callout)
• T Button (Turbo)

Back Buttons:

• ZR / ZL (Magnetic Detachment Buttons)
• GR / GL (Dual Programmable Buttons)
• SR / SL
• SYNC Button

Power On/Off

• Power On (Reconnect): In off state, press any button to power on and enter reconnect mode.
• Power On (Pairing): In off state, hold SYNC for 3 seconds to power on and enter pairing mode.
• Power Off: In on state, hold the left controller's Capture button / right controller's Home button for 3 seconds.
• Immediate Power Off: In on state, short press the SYNC button.
• Auto Power Off: The controller will power off if the connected host enters sleep mode or turns off Bluetooth.

Turbo Function

The Turbo function allows for rapid-fire input of buttons.

1. Assign Turbo:
   • On the left controller, hold the T Button + UP, DOWN, LEFT, RIGHT, ZL, or L.
   • On the right controller, hold the T Button + A, B, X, Y, ZR, or R.
   Then hold the assigned button to enable rapid-fire. The RGB indicator flash frequency matches the turbo speed.
2. Auto Turbo: Press and hold the assigned Turbo button combination again to set the corresponding buttons to auto turbo mode.
3. Cancel Turbo: Press and hold the assigned Turbo button combination again to cancel the turbo function for the corresponding buttons.
4. Clear All Turbo: Press and hold the left or right T Button for 5 seconds. The controller will vibrate for 1 second, indicating all turbo assignments for that controller have been cleared.

Turbo Speed Adjustment

There are three adjustable speeds: Fast / Medium / Slow. The default speed is Medium.

• To increase the turbo frequency, hold T Button + push the joystick up.
• To decrease, hold T Button + push the joystick down.

The controller will vibrate briefly each time the turbo speed is adjusted.

Dual Macro Programming (GL/GR Buttons)

The two customizable buttons GL/GR on the back of the controller can be mapped to specific function keys.

• GL can be mapped to: UP, DOWN, LEFT, RIGHT, L, ZL, L3, -.
• GR can be mapped to: A, B, X, Y, R, ZR, R3, +.

Operation Steps:

1. While connected to the host, hold the T Button and press the GL/GR button once, then release to enter customization mode. The RGB indicator will flash white rapidly, and the controller will vibrate for 1 second.
2. After entering customization mode, press a desired function key (e.g., L for GL or A for GR). The indicator will flash once, confirming the key has been mapped.
3. Press the GL/GR button again to exit customization mode for that controller. The controller will vibrate for 1 second, and the RGB indicator will return to its original channel indication.
4. During customization, multiple function keys can be input in sequence for a single GL/GR button to create a macro. Press the GL/GR button again to exit and save as a macro key. A single custom button can store up to 21 key inputs.

Clearing GL/GR Custom Button Functions:

1. While connected to the host, hold the T Button and press the GL/GR button once, then release to enter customization mode.
2. Briefly press the GL/GR button to clear the custom functions assigned to it. A successful clear is indicated by 1 second of vibration.

RGB Lighting

The controller features 9 RGB lighting modes, including eight solid colors and one mixed-color mode.

1. Cycle Lighting Modes: Hold the T Button and single-press the left controller's - button or the right controller's + button to cycle through modes.
2. Turn Off/On RGB Lighting: Hold the T Button and double-press the left controller's L3 or the right controller's R3 button to turn off all RGB lighting. Repeat to activate mixed-color breathing mode, and a third time for mixed-color flowing light mode.
3. Adjust Brightness: Hold the T Button and press and hold the left controller's L3 or the right controller's R3 button. The brightness will cycle from dim to bright. Release the button to set the current level.

Vibration Intensity Adjustment

The vibration intensity of the grip motors can be adjusted to 3 levels: Off, Low, and High. The factory default is Low.

• For the left or right controller, hold the T Button and push the joystick left (decrease) or right (increase) to adjust the intensity.

The levels cycle through Off → Low → High. The controller will vibrate at the corresponding intensity for 1 second after each adjustment. The current vibration intensity will be remembered even after the controller is powered off.

Charging

Via Console Charging

1. Magnetically attach controllers to the sides of the Switch 2 console.
2. While the console is charging via its adapter, the controllers also charge.
3. The RGB indicator breathes in its current color and stays solid when fully charged.

Via Controller's USB Port Charging

1. Connect a USB-C cable directly to the controller.
2. The RGB indicator breathes red while charging and turns off when fully charged.

Note: Cannot charge via controller's USB port while connected to a host.

Via Center Bridge Charging

1. Connect a charger to the center bridge's charging port.
2. Both left and right charging indicators on the bridge will flash red for 0.5s, then green for 0.5s, then turn off, indicating successful self-test and standby mode.
3. Place a controller into a charging slot; its corresponding indicator lights solid red. It turns solid green when fully charged.
4. Removing the controller turns off its indicator.

Maintenance

Precautions

• Do not expose to liquid: Avoid contact with water or other liquids to prevent damage to internal components.
• Do not disassemble: Unauthorized disassembly may void the warranty and cause damage.
• Avoid dropping: Protect the controller from drops or impacts to prevent physical damage.
• Avoid extreme temperatures: Do not expose the controller to extremely high or low temperatures.

Troubleshooting

Low Battery Warning

When the controller's battery voltage drops below 3.5V during connected use, the RGB indicator flashes red rapidly to warn that the controller needs charging. If the voltage falls below 3.4V, the controller automatically shuts down.

Auto Sleep

When connected to a host, the controller enters sleep mode after 10 minutes of inactivity. The sleep timer can be adjusted in the Keylinker App.

Reset

If the controller malfunctions (e.g., button confusion, freeze, connection failure), try resetting it:

• Press and hold the HOME or Capture button for 10 seconds.
• Alternatively, short press the SYNC button to reset the controller state.

Lock Mode

Activate: With the controller off, press and hold the SL + SYNC (MODE) buttons for 5 seconds. The RGB indicator flashes red slowly 3 times, and the controller enters lock mode. Pressing any button will not wake it.

Deactivate: Connect the controller to a host magnetically or plug in a USB cable for charging. This exits lock mode, allowing wake-up via any button.

Gyroscope Calibration

Left Controller: In sleep mode, press the combo L + UP + CAP (Capture button) simultaneously. Enter calibration mode (RGB indicator flashes cyan slowly). Place the controller flat on a level surface/in a jig. Press -, wait a moment to exit calibration mode. Calibration complete.

Right Controller: In sleep mode, press the combo R + X + HOME simultaneously. Enter calibration mode (RGB indicator flashes cyan slowly). Place the controller flat on a level surface/in a jig. Press +, wait a moment to exit calibration mode. Calibration complete.

Alternative Method via Host: On the console, go to Settings > Controllers & Sensors > Calibrate Motion Controls, then press and hold "+" or "-".

Joystick Calibration

After connecting to the host, go to Settings > Controllers & Sensors > Calibrate Control Sticks to calibrate the joysticks.

Firmware Upgrade

1. OTA via Phone: Connect to the KeyLinker App and use the OTA upgrade option in the menu.
2. Via PC Software: Start the latest firmware upgrade software on a PC. With the controller off, hold the L3 (left joystick) or R3 (right joystick) button, then connect via USB cable. Once the "Upgrade" button becomes clickable, click it to start the upgrade.

Firmware upgrades do not delete the controller's saved settings.

User Tips

• Compatibility: The NYXI Hyperion 3 is specifically designed for the Nintendo Switch 2. Ensure your console is updated to system version 20.0 or higher for full compatibility.
• Third-Party Product: This is a third-party controller, offering enhanced features and customization options compared to official controllers.
• Carrying Case: While no specific carrying case is included, users may find generic Nintendo Switch 2 cases suitable for protecting the controllers when detached or attached to the console.

Warranty and Support

Declaration of Conformity

Model: NS-202
Product Code: NJ22

The product conforms to EC standards for radio interference. Shenzhen MIKE Morgen Technology Co., Ltd. announces that the NS-202 radio equipment conforms to the Directive. EN IEC 62368-1:2020+A11:2020, EN 50663:2017, EN62479:2010, ETSI EN301489-1 V2.23(2019-11), ETSI EN 301 489-17 V3.2.4(2020-09), ETSI EN 300 328 V2.2.2(2019-07).

The full text of the EU Declaration of Compliance can be found on: www.nyxigame.com

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements and can be used in portable exposure conditions without restriction.

Additional Resources

A full user manual (PDF) is available for download here.