Introduction
Thank you for choosing the SZSINOCAM Dual Lens WiFi Security Camera. This manual provides detailed instructions for the installation, operation, and maintenance of your camera. Please read this guide thoroughly before use to ensure proper functionality and safety.
Important Note: This camera supports 2.4GHz WiFi connections only. It does not support 5GHz WiFi. Please ensure your network is configured accordingly. If you have any questions, please contact customer support.

Figure 1: Camera features overview, highlighting 2.4GHz WiFi, dual-lens, motion alarm, and motion detection.
Safety Information & Compliance
Disclaimer: Camera products can only be used for purposes permissible under applicable law and regulations. Misuse of the product for any illegal activities is strictly forbidden. Please comply with the applicable laws and regulations in your country/area.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Statement: To maintain compliance with FCC's RF Exposure guidelines, this equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This device and its antenna(s) must not be co-located or operate in conjunction with any other antenna or transmitter.
Package Contents
Please check the package for the following items:
- SZSINOCAM Dual Lens WiFi Security Camera
- Solar Panel (if applicable to your model)
- Threaded Bracket
- Screws and Anchors
- USB Cable (for charging, 5V adapter not included)
- Quick Start Guide (this manual)

Figure 2: Smart Dual-Lens Camera with key features.
Setup
1. Camera Structure Overview

Figure 3: Detailed view of the camera's components and ports.
- MIC: Microphone for audio input.
- Night lights: For enhanced night vision and deterrence.
- Wi-Fi Antenna: For 2.4GHz wireless connectivity.
- TF card/Reset: Combined slot for TF card and reset button.
- Reset button: Used to reset the camera to factory settings.
- TF card slot: Supports micro TF cards up to 256GB (not included).
- Speaker: For two-way audio communication and alarms.
- Lens: Dual lenses for wide and detailed views.
- PIR: Passive Infrared sensor for motion detection.
- OFF-ON: Power switch for the camera.
- Charge port: USB port for charging the built-in battery.
2. Initial Charging
The camera has a built-in rechargeable battery. Due to shipping safety regulations, the battery is not fully charged upon arrival. Please fully charge the camera using a USB cable (5V adapter not included) before first use.
- Connect the USB cable to the camera's charge port and a 5V power adapter.
- The LED indicator light will be red during charging.
- The red light will turn off when the camera is fully charged.
- A full charge typically takes about 5-6 hours.
3. Download the O-KAM Pro App
The O-KAM Pro app is required to set up and control your camera. You can download it by scanning the QR code below or searching for "O-KAM Pro" in your mobile device's app store (Google Play Store or Apple App Store).

Figure 4: Scan to download O-KAM Pro app.
4. App Account Registration & Login
For New Users:
- Open the O-KAM Pro app.
- Select your country and click "Sign up".
- Enter your email, desired username, and password.
- Complete any required verification steps.
- Sign in to your newly created account.
For Existing Users:
- Simply log in directly with your existing O-KAM Pro account credentials.
5. Adding Your Device
Before adding the camera, ensure your phone is connected to the 2.4GHz WiFi network that the camera will use. The camera does not support 5GHz WiFi.
- Power on the camera. Wait until you hear the APP connection prompt. If no prompt is heard, you may need to reset the camera.
- On the app's homepage, tap the "+" icon in the top right corner.
- Choose the appropriate connection method (e.g., "Wireless camera" to scan the QR code on the device).
- Follow the on-screen instructions to connect the camera to your 2.4GHz WiFi network.
- Enter your WiFi password when prompted.
- Wait for the camera to connect to the router/server. The app will indicate successful binding.
6. Camera Installation
Choose a suitable installation spot. The recommended installation height is 2-2.5 meters (approximately 6.5-8.2 feet). Ensure the camera's line of sight is not blocked and that the PIR motion sensor has a clear detection area (up to 10 meters or 30 feet).
Mounting the Camera
- Use the provided drilling template to mark 4 holes on the wall.
- Drill 4 holes using a 15/64" (6mm) drill bit.
- Insert the anchors into the drilled holes.
- Align the support plate with the holes and fix it to the wall using the provided screws.
- Align the raised positions on both sides of the camera support with the slots on the support plate.
- Push the camera upward until it is securely connected with the support plate.

Figure 5: Camera mounting steps.
Solar Panel Installation (Optional)
If your package includes a solar panel, follow these steps:
- Screw the gimbal into the back of the solar panel and tighten it with the included nut.
- Attach the threaded bracket to your chosen mounting location using screws and anchors.
- Screw the locking screw into the bracket, ensuring the universal joint is angled upward.
- Adjust the solar panel's angle for optimal sun exposure. It can be adjusted up to 90 degrees.
- Once the desired angle is set, loosen the locking screw, adjust the sleeve rod, and then tighten the locking screw to secure the panel in position.
- After installation, check that all locking mechanisms are tightly secured.

Figure 6: Solar panel installation and adjustment.
Place solar panels in an area that gets full sun year-round. The energy produced by solar panels is affected by weather conditions, seasonal changes, and geographic location. Tilt the solar panel up 30-35° for best results.
Operation
1. Live Streaming Interface
Once your camera is connected, you can access the live stream through the O-KAM Pro app. The interface allows you to view real-time footage, control camera functions, and access recordings.

Figure 7: O-KAM Pro app live streaming interface with dual-screen display.
2. Pan, Tilt, and Digital Zoom
You can remotely control the camera's movement and zoom via the app:
- Pan: Rotate the camera horizontally up to 355°.
- Tilt: Adjust the camera vertically up to 90°.
- Digital Zoom: Zoom in on specific areas of the live feed.

Figure 8: App remote control for Pan and Tilt functions.
3. Two-Way Audio
The camera supports two-way audio, allowing you to communicate with visitors or deter intruders directly through the app.

Figure 9: Two-Way Audio in action.
4. Night Vision Modes
The camera offers both infrared and color night vision modes for clear monitoring in low-light conditions.
- Infrared Night Vision: Provides clear black and white footage in complete darkness.
- Color Night Vision: Utilizes built-in lights to capture full-color video at night.

Figure 10: Infrared vs. Color Night Vision.
5. AI Functions & Alarms
The camera is equipped with intelligent AI features to enhance security:
- Human Detection: Accurately identifies human figures, reducing false alarms.
- Motion Detection: Triggers recording and alerts upon detecting any movement.
- Motion Alarm: Activates a siren and spotlights to deter intruders.
- App Notification Push: Sends instant alerts to your phone when an event is detected.
- Customized Detection Area: Allows you to define specific zones for monitoring, ignoring irrelevant areas.

Figure 11: Smart Instant Multi-Siren in action.

Figure 12: Customized Detection Area setup.
6. Recording & Storage
The camera supports 24/7 continuous recording with multiple storage options:
- TF Card Storage: Insert a micro TF card (up to 256GB, not included) into the camera's slot. Remember to format the TF card via the app before first use.
- Cloud Storage: Optional cloud storage is available via subscription for secure off-site backup.

Figure 13: Recording and storage options.
7. Device Sharing
You can share access to your camera with family and friends through the O-KAM Pro app:
- Open the app, select your camera on the homepage, go to camera settings, and click "Share".
- A QR code will be generated. Your friends can scan this QR code with their O-KAM Pro app to gain access.
- You can choose to grant full permission (allowing them to set functions) or limited permission (allowing only video viewing).
8. App & Camera Settings
The O-KAM Pro app allows you to manage various camera settings. Some functions may require granting specific permissions on your mobile device (e.g., location, camera, microphone, album access for notifications and features).