1. Introduction
Thank you for choosing the MICTUNING BB60 6-Gang Wireless Switch Panel. This product is designed to provide a clean, professional installation for controlling multiple auxiliary devices in off-road trucks, marine vehicles, SUVs, UTVs, and cars. With its wireless control and customizable modes, it offers convenience and versatility. Please read this manual thoroughly before installation and operation to ensure proper use and safety.

2. Safety Information
- Always disconnect the vehicle's battery before performing any electrical work.
- Ensure all wiring connections are secure and properly insulated to prevent short circuits.
- Do not exceed the maximum current and power ratings specified for the control box.
- Install the control box in a location protected from excessive heat, moisture, and physical damage.
- Use appropriate personal protective equipment (PPE) during installation.
3. Package Contents
The MICTUNING BB60 Wireless Switch Panel package includes the following items:

- 1. Control Box (Power Hub) x1
- 2. Switch Panel x1
- 3. 140 Stickers (Label Sticker Sheet) x2
- 4. User Manual x1
- 5. Bracket x1
- 6. USB Cable x1
- 7. Wires x2
- 8. Fuses x6
- 9. AAA Batteries x2
- 10. Screws x8
- 11. Terminal Connectors x12
- 12. Screwdriver x1
4. Specifications

| Feature | Specification |
|---|---|
| Model Name | BB60 |
| Input Voltage | 12V/24V DC |
| Max. Current Supported | 80A |
| Max. Power (12V) | 960W |
| Max. Power (24V) | 1920W |
| Operating Temperature | -30°C to 85°C (-22°F to 185°F) |
| Control Range | Up to 164FT (50 meters) |
| Switch Panel Dimensions | Approx. 5.4 in (Length) x 1.5 in (Height) |
| Power Source (Panel) | 2x AAA Batteries or USB Powered |
5. Setup and Installation
5.1. Control Box Installation
- Choose a Mounting Location: Select a secure location for the control box, preferably in the engine bay, away from direct heat and moisture. Ensure it's easily accessible for wiring.
- Mount the Control Box: Use the provided screws to securely mount the control box to the chosen surface.
- Connect Power Cables: Connect the main power cable (red) from the control box to the positive terminal of your vehicle's battery or an ACC (Accessory) power source. Connect the ground cable (black) to a suitable chassis ground point.
- Connect Devices: Insert the positive and negative cables of your auxiliary devices (e.g., LED light bars, winches) into the corresponding output ports on the control box. Ensure proper polarity.


5.2. Switch Panel Power Supply
The wireless switch panel can be powered by two AAA batteries (included) or via the provided USB cable.
- Battery Power: Insert the two AAA batteries into the switch panel.
- USB Power: Connect the USB cable to the switch panel and a suitable USB power source.

6. Operation
6.1. Control Mode Setting
The BB60 switch panel offers four customizable control modes for each switch: Toggle, Flash, Strobe, and Momentary. Follow these steps to set your desired modes:
- Enter Setting State: Turn on the switch panel by pressing any two switches simultaneously. Then, press and hold any two switches for 3 seconds until the white backlight turns off and the red indicators above each switch light up and flash. The panel is now in setting state.
- Cycle Through Modes: Press any individual switch repeatedly to cycle through the four available modes. The indicator light above the switch will change color to represent the current mode:
- Red: Toggle Mode (Press once to turn on, press again to turn off)
- Purple: Flash Mode (Flashes at a slower speed, like a turning signal)
- Green: Strobe Mode (Strobes like a warning light)
- Blue: Momentary Mode (Activates only while the button is held pressed)
- Save Settings: Once you have assigned the desired mode to each switch, press and hold any two switches for 3 seconds. The indicators will flash briefly and then turn off, indicating that your settings have been saved.
- Important: After saving settings, please wait for 2 seconds before turning off the panel to ensure the settings are fully saved and to avoid any saving failures.

6.2. Panel Pairing
To establish a wireless connection between the switch panel and the control box, follow these steps:
- Ensure Control Box Power: The control box must be connected to an ACC power source to operate normally and allow for pairing.
- Activate Pairing Mode on Control Box: Press and hold the pairing button on the control box. The pairing indicator light on the control box will illuminate.
- Pair with Switch Panel: While the control box is in pairing mode, press any button on the wireless switch panel.
- Confirmation: The pairing indicator on the control box will flash three times, signifying that the pairing process is successful.

6.3. Video Instructions
For a visual guide on control mode setting, wiring, and panel pairing, please watch the official product video:
7. Maintenance
- Battery Replacement: To ensure smooth operation of the wireless switch panel, replace the AAA batteries after approximately 16 hours of use.
- Fuse Check: Regularly inspect the fuses in the control box. If the indicator next to a fuse does not light up when the corresponding switch is activated, it indicates a faulty fuse. Replace it with a spare fuse of the same rating.
- Cleaning: Keep the switch panel and control box clean and free from dust and debris. Use a soft, dry cloth for cleaning. Avoid using harsh chemicals or abrasive materials.
- Connection Integrity: Periodically check all wiring connections to ensure they remain tight and free from corrosion.
8. Troubleshooting
- Switch Not Responding:
- Check if the switch panel batteries need replacement.
- Ensure the switch panel is properly paired with the control box (refer to Section 6.2).
- Verify that the control box is receiving power from the vehicle's battery/ACC.
- Device Not Activating:
- Check the fuse corresponding to the non-activating device. If the fuse indicator is off, replace the fuse.
- Ensure the device's wiring is correctly connected to the control box output.
- Confirm the device itself is functioning correctly.
- Intermittent Control:
- Check for any obstructions or excessive distance between the switch panel and the control box.
- Ensure there are no strong electromagnetic interferences nearby.
- Replace switch panel batteries.
9. User Tips
No specific user tips were provided in the available data. However, general best practices include:
- Label your switches clearly using the provided stickers for quick identification of functions.
- Test all connections and functions before final installation to ensure everything works as expected.
- Consider the placement of the switch panel for optimal accessibility and visibility while driving.
10. Warranty and Support
MICTUNING products are designed for quality and reliability. For any warranty claims or technical support, please refer to the official MICTUNING website or contact their customer service directly. Keep your purchase receipt as proof of purchase.
For additional information and documents, including a PDF version of the user manual, please visit the product page or the MICTUNING support section online. (Reference: User manual (PDF))