1. Introduction
The GODIAG GT100 PLUS GPT is a versatile testing platform designed for OBDII protocol communication detection and ECU maintenance, diagnosis, programming, and coding. It features a voltage and current display, allowing maintenance engineers to monitor the ECU's working status. This device converts the car's OBD2 interface into a 16-pin connector for signal detection, enabling connection to single or multiple vehicle modules. It can also be used with any diagnostic tool to assess vehicle communication integrity.
Key functionalities include 24V to 12V voltage conversion, DOIP-ENET communication, and GPT support for reading and writing ECU data. Additionally, it can supply power to the car during battery changes, preventing data loss, automatic locking, key remote control failures, and fault light activation. The product utilizes CANH and CANL shielded twisted cables to resist electromagnetic interference and ensure stable communication.
Video: Overview and unboxing of the GODIAG GT100 PLUS GPT.
2. Safety Information
WARNING: CHOKING HAZARD - Small parts. Not for Children under 3 years.
Always ensure proper ventilation when working with vehicle electronics. Disconnect power sources before making or breaking connections to prevent electrical damage or injury. Refer to your vehicle's service manual for specific safety precautions.
3. Package Contents
The GODIAG GT100 PLUS GPT package includes the following items:
- 1pc x GODIAG GT100 PLUS GPT Host Device
- 1pc x GPT Connecting Cable
- 1pc x Ethernet Cable
- 1pc x OBD 2-in-1 Extension Cable
- 1pc x Colored Jumper Cable (DB25)
- 1pc x Power Supply 12V Adapter
- 1pc x Resistance 120 Ohm
- 6pcs x Banana Plugs
- 24pcs x Wire Accessories (Dupont 2.54mm connector female pins)
- 1pc x Operation Manual
Image: All components included in the GODIAG GT100 PLUS GPT package.
4. Specifications
| Item | Specification |
|---|---|
| Diagnostic Port | OBDII |
| Working Voltage | DC 9V-24V |
| Work and Power | 0.5-0.6W |
| Adapter Power | Input AC100V-240V, Output DC12.5V 2.5A |
| Operating Temperature Range | -20 to 70 °C (-4 to 158 °F) |
| Storage Temperature Range | -40 to 85 °C (-40 to 185 °F) |
| Dimension (L x W x H) | 23cm x 18cm x 7cm |
5. Product Overview
The GODIAG GT100 PLUS GPT device features a clear layout for easy connection and operation. Below are diagrams illustrating the device's interfaces and pinout:
Image: Front view of the GODIAG GT100 PLUS GPT, showing ECU and Tool Connectors, voltage/current display, and power switches.
Image: Side view highlighting the DB15 and DC interfaces.
Image: Side view highlighting the DB25 and PS2 GPT interfaces.
OBDII Pinout Description
| Pin | Description | Pin | Description |
|---|---|---|---|
| 1 | Manufacturer Custom | 9 | Manufacturer Custom |
| 2 | SJE1850 Wire (VPW+) | 10 | SJE1850 Wire (Bus-) |
| 3 | Manufacturer Custom | 11 | Manufacturer Custom |
| 4 | Power Grounding | 12 | Manufacturer Custom |
| 5 | Signal Grounding | 13 | Manufacturer Custom |
| 6 | SAEJ2284 (CAN) High | 14 | SAEJ2284 (CAN) Low |
| 7 | ISO9141-2 & ISO/DIS 4230-4K Wire | 15 | ISO9141-2 & ISO/DIS 4230-4L Wire |
| 8 | Manufacturer Custom | 16 | Car Battery Positive |
6. Setup
- Unpack: Carefully remove all components from the packaging. Verify that all items listed in the "Package Contents" section are present.
- Power Connection: Connect the 12V power supply adapter to the DC interface on the side of the GT100 PLUS GPT device. Plug the adapter into a suitable power outlet.
- Initial Power On: Turn on the main power switch on the GT100 PLUS GPT. The voltage and current display should illuminate, indicating the device is receiving power.
- Connect to Vehicle (if applicable): For in-vehicle diagnostics, connect the OBD 2-in-1 extension cable to the vehicle's OBDII port and then to the GT100 PLUS GPT's "Car Connect" port.
- Connect Diagnostic Tool (if applicable): Connect your diagnostic or programming tool to the GT100 PLUS GPT's "Tool Connector" port using the appropriate cable.
7. Operating Instructions
7.1. GPT Function for ECU Read/Write
The GT100 PLUS GPT supports GPT (General Purpose Timer) functionality to read and write ECU data without disassembling the ECU. This includes support for OBD2 BENCH (CAN bus & K-Line) and GPT BOOT CNF1 protocols. Connect the GPT connecting cable to the PS2 GPT interface on the device and the corresponding pins on the ECU.
7.2. OBDII Diagnostic Interface Communication Status and Voltage Display
When connecting the vehicle and a diagnostic tool via OBDII, the LEDs on the GT100 PLUS GPT will indicate the communication status. The device continuously monitors and displays the voltage of the vehicle's OBDII interface in real-time. If the voltage drops below 11V, it is crucial to stop diagnosis and programming to prevent data loss, module locking, or the vehicle becoming unable to start. This function supports OBD2 BENCH full protocols.
Image: GT100 PLUS GPT connected to a vehicle's OBDII port and a diagnostic tool, illustrating voltage monitoring.
7.3. DOIP-ENET Diagnostics
The device supports DOIP-ENET communication, enabling diagnostic programming and coding for vehicles that utilize the DOIP protocol, such as BMW, Mercedes-Benz, Volkswagen, Audi, Land Rover, Volvo, and Geely. Please note that specific diagnostic software is not provided with the GT100 PLUS GPT.
7.4. 24V to 12V Voltage Conversion
The GT100 PLUS GPT can convert the 24V voltage from the diagnostic interface of heavy trucks, light trucks, pickups, and other commercial vehicles into a stable 12V output, making it compatible with standard 12V diagnostic equipment.
7.5. Checking Diagnostic Tool Communication Signals
Use the GT100 PLUS GPT to verify if your diagnostic, programming, or coding tool is sending proper communication signals. The LED indicators will help confirm signal integrity.
Image: GT100 PLUS GPT connected to a vehicle's OBDII port and a diagnostic tool, checking communication signals.
7.6. Single ECU Module Connection
For focused diagnosis and programming, the GT100 PLUS GPT can be connected to a single ECU module. This setup is ideal for bench testing, allowing users to work on individual modules without affecting other vehicle systems.
Image: GT100 PLUS GPT connected to a single ECU module for diagnosis and programming.
7.7. Key Programming
The GT100 PLUS GPT assists in key programming for various vehicle brands, including VW, Porsche, and Mitsubishi, especially in all-keys-lost scenarios. It can activate instrument clusters or immobilizer modules.
- VW 4th/5th Generation (All Keys Lost): Short-circuit banana connector PIN 16 to PIN 1 on the GT100 PLUS GPT to illuminate the dashboard. Then, use a key programmer tool connected to the GT100 PLUS GPT's female adapter for data collection. Note: Some dashboards may not light up, but data collection can still proceed (e.g., A6L Q7).
- Toyota Engine ECU Replacement / All Keys Lost: Short-circuit PIN13 to PIN4.
- Mitsubishi Key Programming (All Keys Lost) / OBDII Setup (All Remote Keys Lost): Short-circuit PIN1 to PIN4.
- Porsche Cayenne Key Programming (All Keys Lost / All Remote Keys Lost): Short-circuit PIN3 to PIN7.
Image: GT100 PLUS GPT used for key programming, connecting to a key programmer and an immobilizer module.
7.8. Non-Standard OBD2 Protocol Display
The yellow banana connectors on the GT100 PLUS GPT (corresponding to Pins 1, 9, 3, 11, 12, 13, 8) can display CAN BUS or K-Line communication protocols. The GT100 PLUS GPT specifically displays K-Line, PWM, VPW+, and KWP 2000 protocol communication.
7.9. Bench Communication with ECU
Engineers and technicians can quickly communicate with a single ECU on a bench by connecting it to the GT100 PLUS GPT and a diagnostic/programming tool. This method allows for safe testing and programming, minimizing the risk of data loss in other modules that might occur during direct vehicle testing.
Image: GT100 PLUS GPT connected to an ECU on a bench for testing and programming.
7.10. Multiple Vehicle ECU Module Connection
The device facilitates connecting multiple ECU modules simultaneously, which is particularly useful for complex programming tasks like key programming that require interaction with several ECUs.
Image: GT100 PLUS GPT connecting multiple ECU modules for programming.
7.11. Auxiliary Power Supply for Battery Replacement
To prevent data loss or issues with anti-theft remote control data when a vehicle's battery is disconnected, the GT100 PLUS GPT can provide an uninterruptible auxiliary power supply. Connect the device to the vehicle before removing the battery to maintain power to the ECU, ensuring continuous power during the replacement process.
Image: GT100 PLUS GPT providing auxiliary power to a vehicle during battery replacement.
7.12. Extended OBD2 Cable Usage
The GT100 PLUS GPT features an extended 1.4-meter OBD2 cable, addressing situations where diagnostic tool cables are too short or the vehicle's diagnostic port is difficult to access. Always connect the GT100 PLUS GPT first, turn on the power switch, and check the voltage display to confirm normal vehicle power supply. This precaution helps prevent damage to diagnostic and programming tools from modified or faulty vehicle OBD2 ports.
Image: GT100 PLUS GPT connected to a vehicle's OBDII port, highlighting the extended cable length.
7.13. OBD1 and Special Diagnostic Port Conversion
For older OBD1 vehicles or those with special diagnostic ports, connect the GT100 PLUS GPT using the provided banana plugs and DB25 jumper. This allows the OBD1 or special diagnostic port to be converted to a standard OBD2 diagnostic port.
7.14. Truck OBD1 Port Conversion
The GT100 PLUS GPT can convert the OBD1 port of special trucks to a standard OBD2 diagnostic port, adhering to the relevant communication protocols.
Image: GT100 PLUS GPT converting an OBD1 port of a truck to a standard OBD2 diagnostic port.
7.15. CAS Test Platforms
The GT100 PLUS GPT is compatible with various CAS (Car Access System) test platforms:
- Works with CAS1/CAS2 Mechanical Key Test Platform.
- Works with CAS2 CAS3 SER Semi Smart Test Platform.
- Used with BMW-CAS4/CAS4+ Programming Test Platform to verify if programmed keys function correctly.
Image: GT100 PLUS GPT used with a BMW CAS4/CAS4+ programming test platform.
7.16. BMW FEM/BDC Programming Test Platform
The device supports the BMW FEM/BDC Programming Test Platform for advanced programming and testing of these modules.
Image: GT100 PLUS GPT used with a BMW FEM/BDC programming test platform.
8. Maintenance
- Cleaning: Use a soft, dry cloth to clean the device. Avoid using abrasive cleaners or solvents.
- Storage: Store the GT100 PLUS GPT in a cool, dry place away from direct sunlight and extreme temperatures.
- Cable Care: Inspect all cables regularly for signs of wear or damage. Replace damaged cables immediately to ensure safe and reliable operation.
- Software Updates: Check the official GODIAG website periodically for any available firmware or software updates for your device.
9. Troubleshooting
- Device Not Powering On: Ensure the 12V power adapter is securely connected to both the device and a working power outlet. Check the power switch on the device.
- No Communication with Vehicle/Tool: Verify all cable connections are secure. Check the voltage display on the GT100 PLUS GPT; if below 11V, address the vehicle's power supply. Ensure the correct pins are selected for the communication protocol.
- Inaccurate Voltage/Current Display: Ensure all connections are clean and free of corrosion. If the issue persists, contact support.
- ECU Programming Failure: Double-check all wiring according to the specific ECU diagram. Ensure stable power supply to both the GT100 PLUS GPT and the ECU. Verify that the diagnostic tool is compatible and correctly configured.
10. User Tips
- Quality Assurance: Users have reported the device to be of very high quality and effective for various diagnostic tasks, even if some advanced functions like GPT are not immediately utilized.
- Voltage Monitoring: Always pay attention to the real-time voltage display, especially during critical operations like ECU programming, to prevent potential damage from low voltage.
- Bench Testing: Utilize the bench connection capabilities for single or multiple ECUs to perform tests and programming in a controlled environment, reducing risks to the vehicle.
11. Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the official GODIAG website or contact your authorized dealer. A detailed user manual in PDF format is available for download here.