Introduction
Thank you for choosing the K&F CONCEPT MS-65 Super Crab Clamp. This versatile and robust clamp is designed to securely mount various photography and videography accessories to a wide range of surfaces. Its innovative design allows for flexible attachment to both flat surfaces and round tubes, providing stable support for your equipment.

Specifications
| Feature | Specification |
|---|---|
| Model Number | MS-65 |
| Material | Aluminum alloy |
| Weight | 125g |
| Dimensions (L x W x H) | 8.5 x 6.4 x 2 cm |
| Maximum Load Capacity | 5 kg |
| Clamping Range (Round Tubes) | 20mm - 60mm (0.8" - 2.4") |
| Clamping Range (Flat Surfaces) | Up to 50mm (Max 1.9") |
| Threaded Holes | 1/4" and 3/8" |

Setup and Adjustment
The MS-65 Super Crab Clamp is designed for quick and secure attachment to various surfaces. Follow these steps for proper setup:
- Identify Surface Type: Determine if you are clamping onto a flat surface (e.g., table edge, shelf) or a round/square tube (e.g., tripod leg, pipe, railing).
- Adjust Clamping Blocks: The clamp features two rotatable clamping blocks. For flat surfaces, ensure the blocks are rotated to present their flat, textured sides. For round or square tubes, rotate the blocks to present their curved, textured sides. This ensures optimal grip and stability.
- Position the Clamp: Place the clamp onto the desired surface.
- Tighten the Screw: Turn the orange thumb screw clockwise to tighten the clamp jaws until it firmly grips the surface. Ensure it is snug but do not overtighten.


Operating Instructions
Once the clamp is securely attached, you can mount your accessories:
- Identify Thread Size: The clamp features both 1/4" and 3/8" threaded holes. Choose the appropriate hole for your accessory.
- Attach Accessory: Screw your camera, monitor, fill light, phone clip, or other compatible accessory into the chosen threaded hole. Ensure it is tightened securely.
- Adjust Position: If using with a magic arm or gimbal (sold separately), adjust the arm to achieve your desired shooting angle and position.
The clamp's versatility allows for a wide range of applications:
- Mounting cameras or lights to railings for unique perspectives.
- Attaching monitors or microphones to desks for studio setups.
- Securing equipment to tripod legs or other pipes for added stability or multi-camera setups.


Maintenance
To ensure the longevity and optimal performance of your K&F CONCEPT Super Crab Clamp, follow these maintenance guidelines:
- Cleaning: Wipe the clamp with a soft, dry cloth after each use to remove dust, dirt, or moisture. For stubborn grime, a slightly damp cloth can be used, followed by immediate drying.
- Inspect Rubber Pads: Regularly check the non-slip rubber pads for any signs of wear, tear, or damage. Damaged pads may reduce grip and stability.
- Lubrication: The screw mechanism is designed for smooth operation. If it feels stiff, a small amount of silicone-based lubricant can be applied to the threads.
- Storage: Store the clamp in a clean, dry place away from extreme temperatures and corrosive chemicals.

Troubleshooting
- Clamp is not holding securely:
- Ensure the clamping blocks are rotated to match the surface type (flat for flat surfaces, curved for tubes).
- Verify that the surface material is within the recommended clamping range (20-60mm for tubes, up to 50mm for flat surfaces).
- Check if the thumb screw is fully tightened.
- Inspect the rubber pads for wear or damage; replace if necessary.
- Accessory does not fit the threaded hole:
- Confirm that your accessory uses either a 1/4" or 3/8" screw thread.
- Ensure you are attempting to screw into the correct size hole on the clamp.
User Tips
- Always ensure the clamp is securely tightened before attaching valuable equipment to prevent accidental drops.
- For maximum stability, try to clamp onto the thickest and most stable part of the surface.
- When clamping to delicate surfaces, consider adding a protective layer (e.g., a soft cloth) between the clamp and the surface, although the built-in rubber pads offer good protection.
- The 1/4" and 3/8" threads are standard, making this clamp highly adaptable with most camera accessories.
Warranty and Support
K&F CONCEPT products are manufactured to high-quality standards. For any questions, technical support, or warranty claims, please contact K&F CONCEPT customer service directly. Please retain your proof of purchase for warranty purposes.