1. Introduction
The STEPPERONLINE DSY Series DC servo system is a state-of-the-art solution consisting of a 48VDC 400W servo motor and a 24-70VDC 400W servo driver. This kit is engineered for precision and performance, featuring a servo motor with a rated torque of 1.27Nm, a peak torque of 3.81Nm, and a rated speed of 3000rpm.
It comes standard with a 17-bit single-turn magnetic incremental encoder and adopts a high power density design, allowing it to deliver strong power in a compact size, achieving 3 times the instantaneous overload. The new magnetic circuit design reduces torque ripple, minimizing vibration during operation and providing smoother torque output.
This kit is versatile and can be widely used in various applications such as mobile robots (AMR, AGV), service robots, special robots, logistics warehousing and sorting, medical equipment, instruments, and light textile industries, especially where voltage and size constraints are important.
1.1 Kit Contents
The DSY Series 400W RS485 DC Servo Motor Kit typically includes the following components:
- 1 x DSY-400RS: 400W Pulse/RS485 DC Servo Motor Driver
- 1 x DSY60-400L2A2M17S: 400W 48V DC Servo Motor 3000rpm 1.27Nm 17-Bit Encoder IP65
- 1 x P1-DS-03P15M: 3.0m Motor Cable
- 1 x E2-DS-03AM: 3.0m Encoder Cable
- 1 x RS232-5: 1.0m Debugging Cable
Video: Overview of the STEPPERONLINE DSY Series 400W RS485 DC Servo Motor Kit components.
2. Specifications
2.1 DSY-400RS Servo Driver Specifications
| Parameter | Value |
|---|---|
| Part Number | DSY-400RS |
| Continuous Output Current | 15.0A |
| Maximum Output Current | 48.0A |
| Power Supply Input | 24-70VDC |
| Rated Power | 400W |
| Dimension (L*W*H) | 141mm * 75.5mm * 25.4mm |
| Control Method | MOSFET SVPWM Space vector pulse width modulation algorithm |
| Encoder Interface | 17-bit magnetic encoder; 23-bit optical encoder |
| Network Communication | RS485 (Modbus Communication), RS-232 (PC Debugging) |
| IP Grade / Contamination | IP20 / Contamination Rating 2 |
| Operation Temperature | 0℃~55℃ |
| Storage Temperature | -40℃~80℃ |
| Humidity | 0~90% RH (No dew environment) |
| Elevation | ≤1000m |
| Vibration/Strike | 5.88m/s² / 19.6m/s² |
2.2 DSY60-400L2A2M17S Servo Motor Specifications
| Parameter | Value |
|---|---|
| Part Number | DSY60-400L2A2M17S |
| Rated Power | 400W (0.4KW) |
| Rated Voltage | 48VDC |
| Rated Torque | 1.27Nm |
| Peak Torque | 3.81Nm |
| Rated Current | 10.2A |
| Rated Speed | 3000rpm |
| Inertia | 0.49kg*m²*10⁻⁴ |
| Encoder | 17-bit single-turn magnetic incremental encoder |
| Poles | 10 |
| IP Rating | IP65 |
| Cable Length | 3m (optional lengths are 1.5m and 5m) |
3. Setup and Installation
3.1 Servo Drive Dimensions (DSY-400RS)
The dimensions for the DSY-400RS servo drive are shown below. Ensure adequate space for installation and ventilation.

Figure 3.1: DSY-400RS Servo Drive Dimensions. The drive measures 141mm in length, 75.5mm in width, and 25.4mm in height. Mounting holes are indicated.
3.2 Servo Drive Installation
For optimal performance and heat dissipation, install the servo drive vertically as shown in the diagram. Maintain minimum clearances for proper airflow.

Figure 3.2: Recommended vertical installation for the servo drive. Ensure a minimum clearance of ≥50mm above and below, and ≥10mm between drives for proper air circulation.
3.3 System Structure Diagram
The following diagram illustrates the overall system connections for the servo drive and motor.

Figure 3.3: System structure diagram showing connections for DC power, encoder, motor power, pulse signal output device, serial port line, and RS485 communication devices.
3.4 Main Circuit Terminal Name and Function
Refer to the table below for the names, functions, and specifications of the main circuit terminals.
| No. | Name | Description |
|---|---|---|
| 1 | DC+, DC- | Input control circuit power according to specifications |
| 2 | RB+, RB- (Regenerative Resistor Terminal) | External Brake Resistor Connection Port |
| 3 | Motor power cable | Connect servo motor three-phase and ground wire |
| 5 | Communication port | Connected to PC via RS232 to monitor the drive, test and change parameters, etc. |
| 6 | Communication control | Connected to RS485 communication device |
| 7 | Control port | Connect to host controller for IO signal control |
| 8 | Encoder feedback port | Connected to the motor encoder cable |
3.5 Power Cable Connector
The motor power line pins are defined as follows. The structure diagram shows the connection types.
| Conn.1 Pin | Pin Definition | Conn.2 Pin | Pin Color |
|---|---|---|---|
| 1 | U | U | Red |
| 2 | V | V | Yellow |
| 3 | W | W | Blue |
| 4 | PE | PE | Yellow/Green |

Figure 3.4: Power cable structure diagram showing AnPu Connector Cable (P1) and Circular Connector Cable (P2) with pinouts.
3.6 Encoder Cable Connector
The motor encoder line pins are defined as follows. The structure diagram shows the connection types.
| Conn.1 Pin | Pin Definition | Conn.2 Pin | Pin Color |
|---|---|---|---|
| 7 | 5V | 1 | Blue |
| 8 | 0V | 2 | Orange |
| 3 | SD+ | 5 | Brown |
| 4 | SD- | 6 | Green |
| Shell | PE | Shell | / |
| Battery | / | 3 | BAT+ |
| 4 | BAT- |

Figure 3.5: Encoder cable structure diagram (L=1.5m, 3m, 5m).
3.7 DIDO Port Wiring
The DIDO (Digital Input/Digital Output) port provides various control signals. Ensure correct wiring based on your host computer's output type.
| PIN | Definition | Function |
|---|---|---|
| 1 | BRK+ | Brake output |
| 2 | BRK- | Brake output |
| 3 | DI1 | Digital input 1 |
| 4 | DI2 | Digital input 2 |
| 5 | DI3 | Digital input 3 |
| 6 | ICOM | DI power supply input port, 24V |
| 7 | DO+ | Digital output 1 |
| 8 | DO- | Digital output 1 |
| 9 | PULSE+ | Pulse signal input (5V~24V, compatible) |
| 10 | PULSE- | Pulse signal input (5V~24V, compatible) |
| 11 | SIGH+ | Direction signal input (5V~24V, compatible) |
| 12 | SIGH- | Direction signal input (5V~24V, compatible) |
3.7.1 Digital Input Circuit (DI1-DI3)
The digital input circuit can be configured for different host computer output types:
- When the host computer is relay output:

Figure 3.6: Digital input wiring for relay output.
- When the host computer is open collector output (NPN input):

Figure 3.7: Digital input wiring for NPN open collector output.
- When the host computer is open collector output (PNP input):

Figure 3.8: Digital input wiring for PNP open collector output.
Note: The mixing of NPN and PNP inputs is not supported.
3.7.2 Digital Output Circuit (DO1)
The digital output circuit can be configured for different host computer input types:
- When the host computer is a relay input:

Figure 3.9: Digital output wiring for relay input. Ensure to connect a freewheeling diode in the correct direction to prevent damage.
- When the host computer is optocoupler input:

Figure 3.10: Digital output wiring for optocoupler input. A current limiting resistor is required. Max voltage: DC30V, Max current: DC50mA.
3.8 Communication Signal Port (RS485 & RS232)
The DSY-400RS driver supports RS485 (Modbus Communication) via CN1/CN2 and RS232 for PC debugging via CN3.
3.8.1 CN1/CN2 Bus Port (RS485)
CN1 and CN2 are the 485 communication connectors. The pin definitions are:
| Pin | Signal Name | Direction | Terminal |
|---|---|---|---|
| 1 | RS485+ | Output | |
| 2 | RS485- | Output | |
| 3 | GND | Output | |
| 4-8 | - | unused |
3.8.2 CN3 Post Computer Communication Port (RS232)
CN3 is used for RS232 communication to debug the servo drive with a PC. The pin definitions are:
| Pin | Definition | Function | Terminal |
|---|---|---|---|
| 1-2 | - | ||
| 3 | RS232-TXD | RS232 communication port | |
| 4-5 | GND | ||
| 6 | RS232-RXD | RS232 communication port | |
| 7-8 | - | ||
| Shell | PE | Shielding |
3.9 RS485 Wiring Instructions and EMC Precautions
For multi-computer communication, the RS485 bus should use a hand-in-hand structure. The branch length between the bus and the node should not exceed 3m.

Figure 3.11: Network plug 568B serial connection method for RS485. White and Green (Pin 3) for RS485_GND, White and Orange (Pin 1) for RS485+, Orange (Pin 2) for RS485-.

Figure 3.12: Recommended hand-in-hand structure for RS485 multi-computer communication.
3.9.1 Ground PE Connection Requirements
- The ground cable must be thicker than AWG12.
- The PE connects to the ground terminal of a node or the ground bar of the cabinet where the node is located.
- The distance between the PE and the bus should be greater than 5cm.

Figure 3.13: Ground PE connection diagram, showing PE connections for external RS485 nodes and the drive.
3.9.2 Cable Layout Requirements
- Keep the RS485 bus at least 1cm away from the metal backplane of the control cabinet.
- Keep the RS485 bus at least 5cm away from the ground cable.
- Maintain a distance of at least 20cm between the RS485 bus and strong current cables.
- The distance between the RS485 bus and the motor power lines (U, V, W) should be at least 50cm.
3.9.3 Driver Interference Processing
To suppress interference from the driver, consider the following:
- Add a filter magnetic ring at the power code position (position 1). Pass three UVW wires (excluding ground wire PE) through the magnetic ring three times.
- Wrap a magnetic ring at position 2, and pass the power cable (excluding ground PE) through it three times.

Figure 3.14: Diagram showing recommended magnetic loop placement for interference suppression on power and motor cables.
4. Operation
4.1 Basic Control Flow
Follow these steps for basic control and initial setup:
- Check before running: Verify wiring, condition, and machine.
- Power on: Turn on control circuit and main circuit power supply. Ensure servo enable is invalid.
- JOG operation: Perform PC JOG to confirm normal motor rotation without abnormal vibration or sound.
- Parameter set: Set common parameters and relevant parameters for the chosen control mode.
- Servo run: First run at low speed, set relevant parameters for the desired goal, and debug the driver.
- Servo stop: Disable servo, trigger servo failure shutdown, overtravel stop, or emergency stop.
4.1.1 Check Before Running
Before operating the servo driver and motor, perform the following checks:
- Control circuit power input terminals (DC+, DC-) must be connected correctly.
- Output terminals (U, V, W) of the main circuit and motor cables must have the same phase and be correctly connected.
- All control signal cables must be correctly wired, including external signals like brake and overtravel protection.
- Servo drives and motors must be reliably grounded.
- All cables must be within their specified stress range.
- Wiring terminals must be insulated.
- Ensure no foreign objects inside or outside the servo drive that may cause short circuits.
- Servo drives and external braking resistors must not be placed on combustible objects.
- Servo motor installation, shaft connection, and machine must be reliable.
- Servo motor and connected machinery must be in operable condition.
4.1.2 Power On
Turn on the control loop (DC+, DC-). After connecting the control circuit and main circuit power supply, the bus voltage indicator should show no abnormality. Wait for the host computer to give the servo enable signal. If the driver's red alarm light is on, check wiring and resolve the fault.
4.1.3 JOG Operation
Use JOG mode in the host computer software to verify normal motor rotation without abnormal vibration or sound.
4.2 Brake Setting
The brake prevents the servo motor shaft from moving when the servo driver is not running, keeping the motor locked in position. This prevents moving parts from shifting due to gravity or external forces.
4.2.1 Brake Wiring
The brake input signal connection has no polarity. A 24V power supply is required. The standard wiring example is:

Figure 4.1: Standard brake wiring diagram. Connect DO2+(BK+) and DO2-(BK-) to the brake control relay.
- Ensure the motor brake cable length considers voltage drop; input voltage must be at least 21.6V.
- Avoid sharing the power supply with other electrical appliances to prevent malfunction.
- When connecting a relay, use a freewheeling diode (e.g., UF1010G) in the correct direction.
- Recommended cable size: above 0.5mm².
- The 24V power supply inside the servo driver can directly drive the motor lock and drive current 1A.
4.2.2 Brake Resistor Wiring
When the motor decelerates, energy is fed back to the driver, increasing bus voltage. A braking resistor consumes this energy to prevent damage to the servo drive. DS3 series drivers require an external braking resistor.

Figure 4.2: Wiring diagram for external braking resistor. Connect between RB+ and RB- terminals.
The recommended parameters for the brake resistor are:
| Mode | Brake Resistance Value (Ω) | Brake Resistance Power (W) |
|---|---|---|
| DSY-200RS | 10 | 100 |
| DSY-400RS | 10 | 100 |
| DSY-750RS | 5 | 100 |
| DSY-1200RS | 3.5 | 200 |
4.3 Control Modes
The DSY Series servo drive supports Position, Speed, and Torque control modes, as well as mixed mode switching.
4.3.1 Position Control Mode
This is a common working mode. Key steps include connecting power/cables, performing JOG tests, configuring pulse/direction inputs and DI/DO signals, setting position mode parameters, and adjusting gain.
4.3.2 Speed Control Mode
Similar to position control, this mode requires correct wiring, JOG testing, connecting necessary DI/DO and analog inputs, setting speed mode parameters, and adjusting gain.
4.3.3 Torque Control Mode
This mode involves connecting power/cables, JOG testing, connecting DI/DO and torque command sources, setting torque mode parameters, and enabling servo with appropriate speed limits and torque commands.
4.3.4 Homing Function
The homing function allows the servo drive to find a defined home position. Various homing modes are available, utilizing reverse limit switches, positive limit switches, home switches, and motor Z signals. The specific homing mode (0x6098 parameter) determines the sequence of movements and signal detection.
For detailed information on specific homing modes (e.g., Homing Mode 1-34), refer to the full PDF user manual, Chapter 4, Section 4.2.2.6.
5. Maintenance
To ensure the longevity and optimal performance of your DSY Series Servo Motor Kit, follow these general maintenance guidelines:
- Keep Clean: Regularly clean the servo motor and driver to prevent dust and debris accumulation, which can affect heat dissipation and component lifespan. Use a soft, dry cloth.
- Check Connections: Periodically inspect all cable connections (power, encoder, DIDO, communication) for tightness and signs of wear or damage. Loose connections can lead to intermittent operation or faults.
- Environmental Conditions: Ensure the operating environment adheres to the specified temperature (0℃~55℃) and humidity (0~90% RH, non-condensing) ranges. Avoid exposure to excessive vibration, moisture, or corrosive substances.
- Ventilation: Verify that the servo drive's ventilation openings are clear and unobstructed to allow for proper airflow and cooling.
- Cable Integrity: Inspect cables for any kinks, cuts, or abrasions. Replace damaged cables immediately to prevent electrical hazards or signal loss.
6. Troubleshooting
This section provides guidance on diagnosing and resolving common issues. The servo drive categorizes alarms into two levels: Fault and Warning.
6.1 Fault Diagnosis and Treatment
Faults are serious alarms requiring immediate attention and often a power cycle. They can be non-resettable (requiring re-power) or resettable (cleared via P11-01=1 or DI function 2).
6.1.1 Non-Resettable NO.1 Faults
These faults indicate critical issues that prevent normal operation and require the drive to be re-powered after the cause is eliminated.
| Fault Number (Er_) | Fault Name | Cause of Fault |
|---|---|---|
| 1 | System parameter exception | Abnormal data of servo internal parameters |
| 2 | Product model selection failure | Invalid drive model |
| 3 | Motor model selection failure | P01.00 Function code Set an invalid motor code |
| 4 | Fault in parameter storage | Parameter storage device failure; Parameters read/write too frequently; Control power supply instability; Drive failure |
| 5 | FPGA fault | FPGA initialization exception; FPGA logic version is abnormal; FPGA detected an exception |
| 6 | Encoder matching fault | In absolute value system mode (P00.06 ≠0), an incremental or single-turn absolute value encoder motor is used |
| 7 | Control power supply undervoltage | Control circuit power supply undervoltage |
| 9 | Overcurrent A | Drive or motor parameters are incorrect; UVW phase-to-phase short circuit; Motor burned out; Motor is shorted to ground; Drive failure |
| 10 | Overcurrent B | Servo motor wiring is not normal; Software detects the overcurrent of power transistor |
| 11 | Encoder disconnection | Incremental encoder A/B/Z three-phase line break |
| 13 | Encoder check exception | The bus encoder data check is abnormal; The incremental encoder zero check is abnormal |
| 14 | Motor initial angle detection abnormal | The encoder signal interferes when the incremental encoder is powered on |
| 15 | Motor out of control | Motor UVW phase sequence setting error; UVW wiring error; Initial position or encoder parameter setting error |
| 16 | Current sampling fault | The current A/D sampling circuit is faulty |
| 18 | Motor data verification failure | No motor parameters are written into the encoder EEPROM; Motor parameter verification error |
6.1.2 Resettable NO.1 Faults
These faults can be reset after the cause is addressed.
| Fault Number (Er_) | Fault Name | Cause of Fault |
|---|---|---|
| 20 | Overvoltage | The main circuit DC voltage abnormally high. |
| 21 | Undervoltage | The main circuit DC voltage low. |
| 22 | Overspeed | Speed command exceeds maximum speed; UVW phase sequence error; Speed response too high; Drive failure. |
| 25 | Abnormal motor rotation during bootstrap charging | Abnormal motor rotation during bootstrap charging. |
| 27 | DI terminal parameter setting fault | Different DI are assigned with same function repeatedly. |
| 28 | DO terminal parameter setting fault | Different DO are assigned with same output. |
| 30 | Reference position failure | When using the PTP function, P04.00=5 is not set. |
6.1.3 Resettable NO.2 Faults
These faults can be reset after the cause is addressed.
| Fault Number (Er_) | Fault Name | Cause of Fault |
|---|---|---|
| 43 | Position deviation is too large | In the servo ON state, the position deviation exceeds the position deviation value (P09.09). |
| 46 | Drive overload | Load operation exceeds the inverse time curve of the drive; UVW output may be lack of phase or phase sequence connected incorrectly. |
| 47 | Motor overload | Load operation exceeds the inverse time curve of the motor; UVW output may be lack of phase or phase sequence connected incorrectly. |
| 48 | Motor stall | The mechanical position is stuck, causing the motor current to continuously increase abnormally. |
| 49 | Electronic gear setting error | Inconsistent response of dual-drive motors with gantry structure; Electronic gear ratio exceeds specification range [0.001, 4000]. |
| 50 | Heat sink (fan) overheating | Servo unit heat sink (fan) exceeds the set fault value. |
| 51 | Encoder battery failure | No battery or battery voltage below 2.6V. |
| 52 | Encoder multi-turn count error | Absolute encoder multi-turn count error. |
| 53 | Encoder multi-turn count overflow | Absolute encoder multi-turn count overflow. |
| 54 | Soft limit setting error | Position between positive/negative limit is too short; Motor runs counterclockwise (positive direction) and positive limit value is smaller than negative limit value; Motor runs clockwise (negative direction) and negative limit value is smaller than positive limit value. |
6.2 Reasons for Warning and Treatment
Warnings indicate potential issues that should be addressed to prevent faults.
| Warning Number (Er_) | Warning Name | Cause of Warning |
|---|---|---|
| 81 | Drive overload warning | Warning when 80% of the drive overload limit value is reached. |
| 82 | Motor overload warning | The warning before the motor is about to fail, the warning value is determined by P09-05. |
| 83 | Changed parameters need to be re-powered to take effect | Changed parameters that need to be re-powered. |
| 84 | Reset encoder warning | In enabled state, resets encoder when host computer sending commands. |
| 86 | Forward overtravel warning | Positive overtravel switch POT terminal is valid; The motor position exceeds the maximum soft limit. |
| 87 | Negative overtravel warning | Negative overtravel switch NOT terminal is valid; The motor position exceeds the soft limit minimum. |
| 88 | Divided pulse output setting fault | The number of encoder divided pulses does not meet set condition or range. |
| 89 | Al1\Al2 zero drift too large | Al1\Al2 zero drift too large. |
| 90 | External regenerative resistor overload | External regenerative resistor power is too small. |
| 91 | External regenerative resistor value is too small | The external regenerative resistor is less than the minimum requirement by the drive; Or parameter setting error. |
| 94 | DI emergency brake | External emergency brake E_STOP terminal trigger. |
| 95 | Absolute encoder battery low | Battery voltage is lower than 3.2V. |
| 96 | Homing timeout | Home switch failure; Time limit to find home is too short; High speed for searching home signal is too small. |
| 97 | Mechanical home point offset error | Incorrect homing mode parameter settings for mechanical home offset. |
| 99 | Multi-segment position reference position fault | System not performing homing operation or not set to absolute value system in multi-segment absolute position mode; System not performing zero return operation in multi-segment incremental position mode with P13.07=1. |
| 100 | The homing mode is incorrectly set | Homing mode set to 0, or the mode is not supported. |
6.3 Alarm Light Information Description
The servo drive's alarm light provides visual cues for different fault types:
| Fault | Description | Flicker Frequency | Flicker Number | Flicker Times | Cyclic Flicker |
|---|---|---|---|---|---|
| Voltage fault | Overvoltage, Undervoltage (The main circuit) | 1HZ | 1 | 3 seconds | YES |
| Current fault | Overcurrent (Overcurrent A, Overcurrent B) | 1HZ | 2 | 3 seconds | YES |
| Overload/ Motor stall | Drive overload, Motor overload, Motor stall | 1HZ | 3 | 3 seconds | YES |
| Parameter setting error | DI/DO terminal parameter setting fault, Soft limit setting error | 1HZ | 4 | 3 seconds | YES |
| Encoder error | Encoder matching fault, Encoder disconnection, Encoder check exception | 1HZ | 5 | 3 seconds | YES |
| Motor verification error | Moto data verification failure | 1HZ | 6 | 3 seconds | YES |
| Remaining faults | Faults other than the above faults | Stay on | |||
| No faults | - | Stay off |
7. User Tips
- Initial Setup: Always perform a JOG test after initial wiring to confirm motor rotation and check for abnormal sounds or vibrations before proceeding with full operation.
- Parameter Adjustment: When adjusting gain parameters, start with conservative values and gradually increase them while monitoring motor behavior to avoid instability or vibration. Refer to the full manual for detailed gain adjustment procedures.
- RS485 Communication: For reliable RS485 communication, ensure proper grounding (PE connection) and maintain recommended cable separation from strong current lines. Use shielded twisted pair cables for long distances.
- Brake Resistor: If your application involves frequent deceleration or high inertia loads, ensure the correct brake resistor is installed and wired to prevent overvoltage faults.
- Consult PDF Manual: For in-depth parameter lists, advanced control modes (e.g., multi-segment positioning, homing modes), and detailed wiring diagrams, always refer to the comprehensive PDF user manual provided by STEPPERONLINE.
8. Support and Further Information
For detailed technical support, advanced parameter configurations, or specific application guidance, please refer to the official STEPPERONLINE resources:
- Full User Manual (PDF): A comprehensive PDF user manual is available for download. This manual contains extensive details on all parameters, advanced control functions, and detailed wiring diagrams not fully covered in this summary. You can find the PDF manual at DSY-RS Series Low-voltage Servo Drive User Manual (V1.0).
- Web: www.omc-stepperonline.com
- Sales: sales@stepperonline.com
- Support: technical@stepperonline.com
- Address: 15-4, #799 Hushan Road, Jiangning, Nanjing, China
- Tel: 0086-2587156578