1. Introduction
The A6-PN series is a fast, reliable, and accurate platform servo drive from STEPPERONLINE, covering the most common power range of 0.40 kW to 1.0 kW for general automation. It supports both single-phase and three-phase power supply systems. It features a space-saving design and excellent servo control performance.
Working together with the A6 servo motor, the A6-PN series servo drive can optimize performance and ease of use. Compatible with Siemens 200/300/1200/1500 series PLCs, the A6-PN series servo drive provides efficient and convenient motion control solutions for various industries.
2. Safety Information
2.1. Legal Information Statement
- The product described in this documentation may be operated only by personnel qualified for the specific task in accordance with the relevant documentation.
- All operations on the product must follow respective descriptions provided in the documentation, in particular, its warning notices and safety instructions.
- Damage caused by improper use is not covered by warranty.
- The company will disclaim any legal liability for any personal injury or property damage caused by improper usage.
2.2. General Safety Precautions
CAUTION
- Do not connect the input power cables to the output terminals U, V and W. Failure to comply may cause damage to the servo drive.
- Do not touch power terminals within 10 minutes after power-off because high voltage exists inside the drive after power off.
- Do not bundle power cables and signal cables together or route them through the same duct. Power cables and signal cables must be separated by a distance of at least 30 cm to prevent interference.
- Do not turn on and off the power supply frequently (once a minute). Failure to comply may cause drive faults.
- Do not power on the servo drive when any screw of the terminal block or any cable becomes loose. Failure to comply may cause a fire.
- When cables are bundled in a metal duct, take the current reduction ratio into consideration because of the inadequate cooling condition of the duct.
- Select cables based on the ambient temperature of the controller: When the ambient temperature is high, use heat-resistant cables. Teflon cables are recommended.
- Take heat preservation measures in low-temperature environments because the surface of regular cables may be easily hardened and cracked under low temperature.
- Use cables whose bending radius is over 10 times its outer diameter, to prevent the internal conductor from breaking due to long-term bending.
- Use cables that can resist a voltage of 600 V AC or above and have a rated temperature of 75°C or above for the main circuit.
- Use a grounding cable with the same cross-sectional area as the main circuit cable. If the cross-sectional area of the main circuit cable is less than 1.6 mm², use a grounding cable with a cross-sectional area of 2.0 mm².
- Ground the drive reliably. Failure to comply may result in malfunction or even damage of the drive.
- Use shielded cables to comply with the EMC requirements.
3. Product Overview
3.1. Key Features
- Excellent performance: High response (2 kHz speed loop bandwidth), high accuracy (17-bit absolute encoder), high dynamics (DSC mode), high adaptability (standard PROFIDRIVE protocol, mainstream PROFINET communication PLCs).
- Sophisticated and novel design: Integrated communication ports, compact design for narrow spaces, easy connection with serial or USB commissioning cable, support for PROFINET bus servo parameter copy.
- Safe and reliable: Built-in dynamic brake function, optional high-protection model for harsh application environments.
3.2. Components
The kit includes the servo motor driver, servo motor, and necessary cables.


3.3. Servo Drive Component Layout (SIZE A)

The following table describes the numbered components:
| No. | Name | No. | Name |
|---|---|---|---|
| ① | Commissioning and communication port (CN6) | ⑦ | STO terminal port (CN5) |
| ② | Display and operation area | ⑧ | QR code on machine |
| ③ | Control signal port (CN1) | ⑨ | EtherCAT communication network port (CN3 and CN4) |
| ④ | Power input | ⑩ | Encoder signal port (CN2) |
| ⑤ | Braking resistor port | ⑪ | Motor power output |
| ⑥ | Charging indicator | ⑫ | System ground |
NOTICE
The above figure describes the component layout of the SIZE A drive. Component layout of other models may be different. For positions of ports of other models, see section 3.3 Ports.
4. Specifications
4.1. Rated Data
Single-phase 220 V Servo Drive
| Item | SIZE-A | SIZE-B |
|---|---|---|
| Power | 0.4 kW | 0.75 kW |
| Drive model A6-PN | A6-400PN | A6-750PN |
| Continuous output current (Arms) | 2.8 | 5.5 |
| Maximum output current (Arms) | 10.1 | 16.9 |
| Main circuit power supply | Single-phase 200–240 V AC, −10% to +10%, 50/60 Hz | |
| Control circuit power supply | Powered up by the bus, sharing one power supply and rectification part with the main circuit | |
| Braking capability | External braking resistor | Built-in braking resistor |
Single-phase/Three-phase 220 V Servo Drive
| Item | SIZE-C |
|---|---|
| Power | 1.0 kW |
| Drive model A6-PN | A6-1000PN |
| Continuous output current (Arms) | 7.6 |
| Maximum output current (Arms) | 23 |
| Main circuit power supply | Single-phase/three-phase 200–240 V AC, -10% to +10%, 50/60 Hz |
| Control circuit power supply | Single-phase 200–240 V AC, -10% to +10%, 50/60 Hz |
| Braking capability | Built-in braking resistor |
NOTICE
The main circuits of A6-1000PN driver can be connected to a single-phase or a three-phase power supply, depending on which one is available on site.
4.2. Technical Specifications
Basic Specifications
| Item | Specifications |
|---|---|
| Control mode | IGBT PWM control, sine wave current drive mode, 220 V, 380 V: Single-phase or three-phase full-bridge rectification |
| Encoder feedback | 17-bit multi-turn absolute encoder, which can be used as a single-turn absolute encoder in absence of the battery |
| Operating temperature | 0°C to +55°C (over 45°C: derate 10% for every additional 5°C) |
| Storage temperature | -40°C to +70°C |
| Altitude | Up to 2000 m. For altitude above 1000 m, derate 1% for every additional 100 m |
| IP rating | IP20 (except for the power terminal IP00) |
Speed/Torque Control Mode
| Item | Specifications |
|---|---|
| Speed control range | 1:6000 (The lower limit is the threshold within which the servo drive keeps running with the rated torque load.) |
| Speed loop bandwidth | 3 kHz |
| Torque control accuracy | ±1% |
| Ramp time | 0 s to 600 s (This parameter can be set for acceleration and deceleration separately.) |
| Speed reference input | Source of network-type references: PROFINET communication |
| Torque reference input | PROFINET communication |
Position Control Mode
| Item | Specifications |
|---|---|
| Positioning time | 1 ms to 10 ms |
| Position reference | Source of network-type references: PROFINET communication |
| Digital input (DI) signal | P-OT (positive limit switch), N-OT (negative limit switch), HomeSwitch (home switch), TouchProbe1 (probe 1), TouchProbe2 (probe 2) |
| Digital output (DO) signal | 3 DOs, Load capacity: 50 mA, Voltage range: 5 V to 30 V, S-RDY (servo ready), ALM (fault output), BK (brake output) |
Built-in Functions
| Item | Specifications |
|---|---|
| Overtravel (OT) prevention | The servo drive stops immediately when P-OT or N-OT becomes active |
| Protection function | Protections against overcurrent, overvoltage, undervoltage, overload, main circuit detection error, heatsink overheat, overspeed, encoder error, CPU error, and parameter error |
| LED display | Main power supply CHARGE indicator, 5-digit LED display |
| Vibration suppression | Five notches (including two adaptive notches), 50 Hz to 8000 Hz |
| Connection protocol | RS232, PROFINET, USB |
| Multi-station communication | 65535 (PROFINET, dependent on the PLC) |
| Axis address setting | 0 to 247 set through the software (RS232), Allocated automatically by the host controller (PROFINET) |
| Function | Status display, user parameter setting, monitored value display, alarm tracing display, jogging, and speed/torque reference signal observation |
| Other | Gain tuning, alarm record, and I/O setting |
Communication Specifications
| Item | Specifications |
|---|---|
| Communication protocol | PROFINET protocol, RT and IRT modes |
| Process data | Commonly-used telegrams |
| Non-cyclic data | Access to industry standard parameters and function code parameters |
| Bus cycle | RT mode: minimum 1 ms, IRT mode: minimum 500 µs |
| Synchronization jitter | <1 µs |
| Physical layer | 100 BASE-TX |
| Baud Rate | 100 M Bit/S (100Base-TX) |
| Duplex mode | Full duplex |
| Topology | Ring, linear, star, tree |
| Transmission medium | Shielded Ethernet cable of Cat5e or above |
| Number of slaves | Up to 65535 supported by protocol (Dependent on PLC performance.), Up to 100 tested |
| Communication bit error ratio | 10-10 Ethernet standard |
| I&M data | I&M0 to I&M4 |
| Configuration version | TIA Portal V17 SP1 or later versions, STEP7 V5.5 SP4 or later versions |
| PROFINET version | V2.4 |
| PROFINET interface | Number of ports: 2 |
| Alarm/Diagnosis information | Supported |
| DCP CALL | Supported |
| MRP | Supported |
| MRPD | Supported |
| PROFINET system redundancy | Supported |
| Boot priority | Supported |
| Port disabling | Supported |
| Configuration free upon device change | Supported |
4.3. Servo Motor Specification

4.4. Product Dimensions
400W AC Servo Motor Driver

400W AC Servo Motor

4.5. Motor Torque-Speed Characteristics
The following graphs illustrate the continuous and short-time work areas for different motor models at 3000 rpm.

5. Installation Guide
The A6-PN series servo drive must be installed on a base through a backplate. For the mounting holes, refer to the dimensions diagrams of each model.
5.1. Installation Dimensions
SIZE A (rated power: 0.4 kW)

SIZE B (rated power: 0.75 kW)

SIZE C (rated power: 1.0 kW)

5.2. Dimensions of the Outer Packing Box
| SIZE | Drive Model | Outer Length | Outer Height | Outer Width | Weight |
|---|---|---|---|---|---|
| A | A6-400PN | 215 mm | 85 mm | 195 mm | 0.78 kg |
| B | A6-750PN | 220 mm | 95 mm | 215 mm | 1.04 kg |
| C | A6-1000PN | 220 mm | 95 mm | 215 mm | 1.20 kg |
5.3. Fixing with Screws
NOTICE
- SIZE-A/B/C: M4 screws, 1 each on top and bottom. Torque: 1.3 N·m to 1.6 N·m.
6. Wiring and Connections
6.1. System Topology (SIZE A)

6.2. System Wiring

6.3. Ports Overview
SIZE A Ports
The following table details the ports for SIZE A drives.
| Port | Function |
|---|---|
| CN6 | Commissioning and communication port |
| CN3 | Communication network port IN |
| CN1 | User control port |
| L1/L2 | Main power input |
| P+/C | External braking resistor |
| N- | Bus negative electrode |
| U/V/W | Motor power output |
| PE | Motor grounding terminal |
| CN5 | STO functional port |
| CN4 | Communication network port OUT |
| CN2 | Encoder port |
SIZE B Ports
The following table details the ports for SIZE B drives.
| Port | Function |
|---|---|
| CN6 | Commissioning and communication port |
| CN3 | Communication network port IN |
| CN1 | User control port |
| L1/L2 | Main power input |
| P+/D/C | External braking resistor |
| N- | Bus negative electrode |
| U/V/W | Motor power output |
| PE | Motor grounding terminal |
| CN5 | STO functional port |
| CN4 | Communication network port OUT |
| CN2 | Encoder port |
SIZE C Ports
The following table details the ports for SIZE C drives.
| Port | Function |
|---|---|
| CN3 | Communication network port IN |
| L1C/L2C | Control power input |
| R/S/T | Main power input |
| P+/D/C | External braking resistor |
| N- | Bus negative electrode |
| U/V/W | Motor power output |
| PE | Motor grounding terminal |
| CN4 | Communication network port OUT |
| CN6 | Commissioning and communication port |
| CN5 | STO functional port |
| CN1 | User control port |
| CN2 | Encoder port |
6.4. Drive Terminals
| Terminal | Pin | Description |
|---|---|---|
| Main circuit terminals of SIZE A | L1 and L2: Power input terminals | Connected to the input power supply as per the rated voltage class on the nameplate. |
| P+ and N-: Servo bus terminals | Used when multiple servo drives share one DC bus. | |
| P+ and C: External braking resistor connection terminals | If an external braking resistor is needed, connect it between terminals P+ and C. | |
| U, V, and W: Servo motor connection terminals | Connected to U, V, and W phases of the servo motor. | |
| PE: Motor grounding terminal | Connected to the grounding terminal of the motor for grounding purpose. | |
| L1C and L2C: Control circuit power input terminals | Connected to the control circuit power supply as per the rated voltage class on the nameplate. | |
| Main circuit terminals of SIZE B | L1 and L2: Power input terminals | Connected to the input power supply as per the rated voltage class on the nameplate. |
| P+ and N-: Servo bus terminals | Used when multiple servo drives share one DC bus. | |
| P+, D, and C: External braking resistor connection terminals | If an external braking resistor is needed, connect it between terminals P+ and C. Note: Remove the jumper between terminals P+ and D before installing an external braking resistor. Otherwise, the braking transistor will be damaged due to overcurrent. | |
| U, V, and W: Servo motor connection terminals | Connected to U, V, and W phases of the servo motor. | |
| PE: Motor grounding terminal | Connected to the grounding terminal of the motor for grounding purpose. | |
| L1C and L2C: Control circuit power input terminals | Connected to the control circuit power supply as per the rated voltage class on the nameplate. | |
| Main circuit terminals of SIZE C | R, S, and T: Main circuit power input terminals | Connected to the main circuit power supply as per the rated voltage class on the nameplate. |
| P+ and N-: Servo bus terminals | Used when multiple servo drives share one DC bus. | |
| P+, D, and C: External braking resistor connection terminals | If an external braking resistor is needed, connect it between terminals P+ and C. Note: Remove the jumper between terminals P+ and D before installing an external braking resistor. Otherwise, the braking transistor will be damaged due to overcurrent. | |
| U, V, and W: Servo motor connection terminals | Connected to U, V, and W phases of the servo motor. | |
| PE: Motor grounding terminal | Connected to the grounding terminal of the motor for grounding purpose. |
6.5. CN1 User Control Terminal
| Terminal | Pin | Description |
|---|---|---|
| CN1 user control terminal | 10 (DI1) | Positive limit switch |
| 9 (DI2) | Negative limit switch | |
| 8 (DI3) | Home switch | |
| 7 (DI4) | Probe 2 | |
| 11 (DI5) | Probe 1 | |
| 15 (+24V) | Internal 24 V power supply (Voltage range: 20 V to 28 V, Max. output current: 200 mA) | |
| 14 (COM-) | Common terminal (Note: The drive shares a resettable fuse of a 200 mA total current limit with the CN5 Safe Torque Off (STO) function terminal.) | |
| Digital Output | 1 (DO1+) / 6 (DO1-) | Servo ready |
| 3 (DO2+) / 2 (DO2-) | Fault | |
| 5 (DO3+) / 4 (DO3-) | Brake | |
| 1 (+5V) / 2 (0V) | 5 V power supply |
6.6. CN2 Encoder Terminal
| Terminal | Pin | Description |
|---|---|---|
| CN2 encoder terminal | 5 (PS+) / 6 (PS-) | Encoder signal |
| Enclosure (PE) | Shield |
6.7. PROFINET Communication Terminals (CN3 and CN4)
| Terminal | Pin | Description |
|---|---|---|
| PROFINET communication terminals | 1 (TD+) / 2 (TD-) | Data transmit+ / Data transmit- |
| 3 (RD+) / 6 (RD-) | Data receive+ / Data receive- | |
| 9 (TD+) / 10 (TD-) | Data transmit+ / Data transmit- | |
| 11 (RD+) / 14 (RD-) | Data receive+ / Data receive- |
6.8. CN6 Commissioning and Communication Terminal
| Terminal | Type | Description |
|---|---|---|
| CN6 commissioning and communication terminal | Type-C | 1: Type-C to serial, serial to USB 2: Type-C to USB |
6.9. Power Supply Connection
Refer to the safety precautions in Section 2.2 for important guidelines on power supply connections.
6.10. Communication Signal Connection (CN3 and CN4)
Communication signals are connected by PROFINET network cables. Connect CN3 (P1) to the communication port of the master and CN4 (P2) to a slave.

CAUTION
- To enhance the system's anti-interference capability, the EtherCAT communication cable must be an Ethernet Category 5 (100BASE-TX) network cable or high-strength shielded network cable of no more than 100 m.
- PROFINET servo drives support multiple connection methods, and the networking topology provided here is for reference only.
6.11. PROFINET Communication Connection
PROFINET communication supports multiple networking topologies and connection methods:

7. Operation and Commissioning
7.1. Basic Functions of the Servo Drive
The servo system consists of three critical parts: the servo drive, servo motor, and encoder. The servo drive processes input signals and feedback signals to precisely control the position, speed, and torque of the servo motor.
Structure of a Servo System

List of Servo Functions
| Function | Description |
|---|---|
| Measurement probe | Latches the position value when a DI external signal or Z signal of the motor changes. |
| High-resolution encoder | Utilizes a high-performance encoder with a resolution of 1,310,72 P/r. |
| Mechanical characteristics analysis | Analyzes the resonance frequency and other characteristics of the mechanical system when using a PC that has a drive commissioning platform installed on it. |
| Automatic gain adjustment | You only need to set one parameter, and the servo automatically provides a set of matching gain parameters suitable for the current working condition. |
| Gain switchover | Uses different gains in different servo motor status (running or stopping), and switches gains through external terminals during running. |
| Torque disturbance observation | Automatically estimates the disturbance torque on the system and compensates for it to reduce vibration. |
| Resonance suppression | Automatically sets filter characteristics after the servo drive detects mechanical resonant points to suppress system vibration. |
| Torque command filter | Suppresses mechanical resonance that may occur when the servo drive responds too quickly. |
| Position first-order low-pass filter | Enables smooth acceleration and deceleration. |
| Torque limit | Limits the output torque of the servo motor. |
| Velocity limit | Limits the velocity of the servo motor. |
| External braking resistor | Used when the braking capability of the built-in brake resistor of the servo drive is insufficient. |
| Input signal selection | Assigns functions such as emergency stop to corresponding pins. |
| Alarm history | Records the latest 20 alarms and can clear the alarm history. |
| Status display | Displays the status of the servo drive on a 5-digit 8-segment LED. |
| External I/O display | Displays the ON/OFF status of external I/O signals. |
| Forced signal output | Enables the independent output of signals regardless of the servo drive status, useful for checking the wiring of output signals. |
| Trial running mode | Allows running the servo motor directly from the servo drive panel without requiring a start signal. |
| Drive commissioning platform | Enables parameter setting, trial running, status display using a personal computer. |
| Alarm code output | Outputs a 4-digit alarm code when an alarm occurs. |
7.2. Commissioning Tool
The A6-PN series servo drive can be commissioned by the operating panel which consists of an LED display area and five buttons.
Display and Operation Area

Buttons
| Button | Description |
|---|---|
| M (MODE) | Press: Switch/return to menus of different levels. Press and hold: Switch the group number quickly in level-2 menus. |
| ▲ (UP) | Press: Switch the state display quickly in level-1 menus, Increase the value. |
| ▼ (DOWN) | Press: Switch the state display quickly in level-1 menus, Decrease the value. |
| ◀ (SHIFT) | Press: Move the cursor to the left. Press and hold: Enter the JOG mode quickly in level-1 menus, Page up or down when the content is displayed on multiple pages. |
| S (SET) | Press: Switch to the lower-level menu. Execute commands such as storing parameter setpoints. |
Display Menus
When the servo drive is running, the servo drive status, parameters, faults, and monitored values are displayed in the LED display area.
- Status display: Display current servo drive status, such as servo ready or servo running.
- Parameter display: Display parameters and their setpoints.
- Fault display: Display faults and alarms that occurred on the servo drive.
- Monitored value display: Display values of running parameters of the servo drive.
NOTICE
- After power-on, "Init" is displayed in the LED display area and then the system enters the level-1 menu status display mode.
- In the status display mode, select the parameter to be monitored. When the motor rotates, the display area automatically switches to monitored value display. After the motor stops, the display area automatically returns to status display.
- In the parameter display mode, after you select the parameter to be monitored, the system switches to monitored value display.
- Once a fault occurs, the LED display area switches to fault display automatically, with all the LEDs blinking. Press S to stop the LEDs from blinking, and then press M to switch to parameter display.
Level-1 Menu: Status Display
Press ▲ and ▼ to switch among different display modes. Press M to enter a level-2 menu.
Level-2 Menu: Parameter Group Number
Displays the parameter group number in hexadecimal. Press and hold M to switch the group number. Press S to enter a level-3 menu. Press M to return to the level-1 menu.
Level-3 Menu: Offset within Parameter Group
Offset within the parameter group in hexadecimal. Press S to enter a level-4 menu. Press M to return to a level-2 menu.
Level-4 Menu: Parameter Setpoints
Parameter setpoints in decimal. Press ▲ to increase or decrease the value. Press S to confirm the setting. Then, the system displays the new value. Press M to return to a level-3 menu.
7.3. Jogging
Use the jogging function for trial run of the servo motor and servo drive to check whether the servo motor rotates properly without abnormal vibration or noise generated during rotation.
NOTICE
- To use the jogging function, deactivate the S-ON signal. Otherwise, this function cannot be used.
- During the jog, use F30.03 to set the acceleration/deceleration time constant for the velocity/position reference.
Procedure for Setting the Jogging Function
- Start: Power on the servo drive. Press and hold ◀ in the level-1 menu.
- Set parameter F30-00 on the panel: Press S to confirm the setting.
- Set the jog speed: Press ▲ to increase or decrease the value.
- Confirm the motor speed: Press S to confirm the setting.
- JOG-S is displayed. Press ▲/▼.
- Enable forward/reverse motor rotation: Press M.
- Finish.
NOTICE
- Press ▲/▼ to increase or decrease the motor speed for the jog running. If the system exits jog running, the motor speed restores to the initial value.
- Press ▲/▼ to make the servo motor rotate in the forward or reverse direction. After the button is released, the servo motor stops running immediately.
7.4. Inertia Auto-tuning
The load inertia ratio is the ratio of the total moment of inertia of motor load to the moment of inertia of the motor. A correct load inertia ratio facilitates commissioning.
You can set the C00.06 (load inertia ratio) manually, but it is tedious. It can also be automatically auto-tuned by F30.10 (inertia auto-tuning function) of the servo drive.
During auto-tuning, the drive will drive the servo motor to run in the forward or reverse direction multiple times to obtain the load inertia ratio.
Inertia Auto-tuning Process
- Start: Power on the servo drive.
- Set the parameter F30-10 on the panel: Press S to confirm the setting.
- Set the number of auto-tuning turns: Press ▲ to increase or decrease the value.
- Confirm the number of auto-tuning turns: Press S to confirm the setting.
- Display the inertia value: Press ▲/▼.
- Perform auto-tuning on auto/manual gains: Press M.
- End.
8. PROFINET Communication Details
8.1. Overview of PROFINET
PROFINET IO is an Ethernet-based real-time protocol used as a high-level network in industrial automation applications. It provides two real-time communication types: PROFINET IO RT (real-time) and PROFINET IO IRT (isochronous real-time).
- PROFINET IO RT: Used for the transmission of I/O data and alarms. Real-time data is transferred through prioritized Ethernet frames, no special hardware required.
- PROFINET IO IRT: Used for more precise timing requirements, special hardware for IO devices and switches required.
All diagnostic and configuration data is transferred through the non-real time (NRT) channel and the TCP/IP protocol is used.
8.2. Supported Telegrams
The A6-PN series servo drive supports AC1, AC4, AC3, and DSC applications. It supports standard telegrams and Siemens telegrams for velocity control mode and basic positioner control mode.
From the perspective of the drive unit, the received process data represents the receive words and the process data to be sent represents the send words.
Description of Supported Telegrams
| Telegram | Max. Number of PZDs (One PZD = One word) | |
|---|---|---|
| Receive Word | Send Word | |
| Standard telegram 1 | 2 | 2 |
| Standard telegram 3 | 5 | 9 |
| Standard telegram 5 | 9 | 9 |
| Siemens telegram 102 | 6 | 10 |
| Siemens telegram 105 | 10 | 10 |
| Standard telegram 7 | 2 | 2 |
| Standard telegram 9 | 10 | 5 |
| Siemens telegram 111 | 12 | 12 |
| Annex telegram 750 | 3 | 1 |
8.3. Telegrams for Velocity Control Mode
| Telegram | 1 (AC1) | 3 (AC4) | 5 (AC4) | 102 (AC4) | 105 (AC4) |
|---|---|---|---|---|---|
| PZD1 | STW1 | STW1 | STW1 | STW1 | STW1 |
| PZD2 | NSOLL_A | NIST_B | NIST_B | NIST_B | NIST_B |
| PZD3 | ZSW1 | STW2 | STW2 | STW2 | STW2 |
| PZD4 | ZSW2 | ZSW2 | ZSW2 | ZSW2 | |
| PZD5 | G1_STW | G1_STW | MOMRED | MELDW | |
| PZD6 | G1_ZSW | G1_ZSW | G1_STW | G1_ZSW | |
| PZD7 | G1_XIST1 | G1_XIST1 | G1_XIST1 | G1_XIST1 | |
| PZD8 | XERR | XERR | XERR | XERR | |
| PZD9 | G1_XIST2 | G1_XIST2 | G1_XIST2 | G1_XIST2 | |
| PZD10 | KPC | KPC | KPC | KPC |
8.4. Telegrams for Basic Positioner Control Mode
| Telegram | 7 (AC3) | 9 (AC3) | 111 (AC3) |
|---|---|---|---|
| PZD1 | STW1 | STW1 | STW1 |
| PZD2 | SATZANW | SATZANW | POS_STW1 |
| PZD3 | STW2 | STW2 | POS_STW2 |
| PZD4 | MDI_TARPOS | MDI_TARPOS | OVERRIDE |
| PZD5 | MDI_VELOCITY | MDI_VELOCITY | MDI_TARPOS |
| PZD6 | MDI_ACC | MDI_ACC | MDI_ACC |
| PZD7 | MDI_DEC | MDI_DEC | MDI_DEC |
| PZD8 | MDI_MOD | MDI_MOD | MDI_MOD |
| PZD9 | ZSW1 | ZSW1 | ZSW1 |
| PZD10 | ZSW2 | ZSW2 | ZSW2 |
| PZD11 | USER_PZD | ||
| PZD12 | USER_PZD |
8.5. Annex Telegram 750
NOTICE
When telegram 750 is used, the motor will accelerate uncontrollably if any of the following settings are made:
- The torque upper limit is set by PZD M_LIMIT_POS to a negative value.
- The torque lower limit is set by PZD M_LIMIT_NEG to a positive value.
| Telegram | 750 |
|---|---|
| Application Mode | - |
| PZD1 | M_ADD1 |
| PZD2 | M_LIMIT_POS |
| PZD3 | M_LIMIT_NEG |
8.6. I/O Data Signals
Overview of I/O Data in Telegrams
| Signal | Description | Receive Word/Send Word | Data Type | Value and Meaning |
|---|---|---|---|---|
| STW1 | Control word 1 | Receive word | U16 | - |
| STW2 | Control word | Receive word | U16 | - |
| ZSW1 | Status word 1 | Send word | U16 | - |
| ZSW2 | Status word 2 | Send word | U16 | - |
| NSOLL_A | Velocity setpoint A | Receive word | U16 | 4000 hex ≒ 3000 rpm |
| NSOLL_B | Velocity setpoint B | Receive word | U32 | 40000000 hex ≒ 3000 rpm |
| NIST_A | Velocity actual value A | Send word | U16 | 4000 hex ≒ 3000 rpm |
| NIST_B | Velocity actual value B | Send word | U32 | 40000000 hex ≒ 3000 rpm |
| MOMRED | Torque decrease value | Receive word | U16 | 4000 hex = Maximum torque |
| M_ADD1 | Supplementary torque value | Send word | U16 | 4000 hex = Maximum torque, C000 hex = Minimum torque |
| M_LIMIT_POS | Positive torque limit | Send word | U16 | 4000 hex = Maximum torque |
| M_LIMIT_NEG | Negative torque limit | Send word | U16 | C000 hex = Minimum torque |
| M_ACT | Thrust actual value | Receive word | U16 | 4000 hex = Maximum torque, C000 hex = Minimum torque |
| MELDW | Message word | Send word | U16 | - |
| G1_STW | Encoder 1 control word | Receive word | U16 | - |
| G1_ZSW | Encoder 1 status word | Send word | U16 | - |
| G1_XIST1 | Encoder 1 actual position | Send word | U32 | - |
| G1_XIST2 | Encoder 1 actual position | Send word | U32 | - |
| MELDW | Message word | Send word | U16 | - |
| MDI_TARPOS | MDI position | Receive word | U32 | 1 hex ≒ 1 LU |
| MDI_VELOCITY | MDI velocity | Receive word | U32 | 1 hex ≒ 1000 LU/min |
| MDI_ACC | MDI acceleration override | Receive word | U16 | 4000 hex ≒ 100% |
| MDI_DEC | MDI deceleration override | Receive word | U16 | 4000 hex ≒ 100% |
| XIST_A | Position actual value A | Send word | U32 | 1 hex ≒ 1 LU |
| OVERRIDE | Position velocity override | Receive word | U16 | 4000 hex ≒ 100% |
| FAULT_CODE | Fault code | Send word | U16 | - |
| WARN_CODE | Alarm code | Send word | U16 | - |
| user | User-defined receive word (0: No function, 1: Supplementary torque) | Receive word | U16 | 4000 hex ≒ 100% |
| user | User-defined send word (0: No function, 1: Actual torque, 2: Actual current, 3: DI status) | Send word | U16 | 4000 hex ≒ 100% |
| XERR | DSC deviation | Receive word | U32 | - |
| KPC | DSC gain | Receive word | U32 | - |
| SATZANW | Position program block selection | Receive word | U16 | - |
| AKTSATZ | EPOS selected program block | Send word | U16 | - |
| MDI_MOD | MDI mode | Receive word | U16 | - |
Definitions of Control Words
STW1 Control Word (for Telegrams 1 and 3)
| Signal | Description |
|---|---|
| STW1.0 | 1 = ON (Allow enabling pulses), 0 = OFF1 (Ramp to stop, disable pulses, and get ready for switching on) |
| STW1.1 | 1 = No OFF2 (Allow enabling), 0 = OFF2 (Coast to stop, disable pulses, and inhibit switching on) |
| STW1.2 | 1 = No OFF3 (Allow enabling), 0 = OFF3 (Quick stop, disable pulses, and inhibit switching on) |
| STW1.3 | 1 = Allow running, 0 = Inhibit running |
| STW1.4 | 1 = Running condition, 0 = Freeze command |
| STW1.5 | 1 = Running condition, 0 = Freeze command |
| STW1.6 | 1 = Enable setpoint, 0 = Disable setpoint |
| STW1.7 | 0-1 rising edge: Acknowledgment fault |
| STW1.8 | Reserved |
| STW1.9 | Reserved |
| STW1.10 | 1 = Control through PLC, 0 = Not control through PLC |
| STW1.11 | 1 = Start referencing, 0 = Stop referencing |
| STW1.12 | Reserved |
| STW1.13 | Reserved |
| STW1.14 | Reserved |
| STW1.15 | Reserved |
STW1 Control Word (for Telegram 111)
| Signal | Description |
|---|---|
| STW1.0 | 1 = ON (Allow enabling pulses), 0 = OFF1 (Ramp to stop, disable pulses, and get ready for switching on) |
| STW1.1 | 1 = No OFF2 (Allow enabling), 0 = OFF2 (Coast to stop, disable pulses, and inhibit switching on) |
| STW1.2 | 1 = No OFF3 (Allow enabling), 0 = OFF3 (Quick stop, disable pulses, and inhibit switching on) |
| STW1.3 | 1 = Allow running, 0 = Inhibit running |
| STW1.4 | 1 = Do not reject traversing task, 0 = Reject traversing task |
| STW1.5 | 1 = Do not pause traversing task, 0 = Pause traversing task |
| STW1.6 | 0-1 rising edge: Activate traversing task |
| STW1.7 | 0-1 rising edge: Acknowledgment fault |
| STW1.8 | 1 = Enable JOG1, 0 = Disable JOG1 |
| STW1.9 | 1 = Enable JOG2, 0 = Disable JOG2 |
| STW1.10 | 1 = Control through PLC, 0 = Not control through PLC |
| STW1.11 | 1 = Start referencing, 0 = Stop referencing |
| STW1.12 | Reserved |
| STW1.13 | Reserved |
| STW1.14 | Reserved |
| STW1.15 | Reserved |
STW2 Control Word (for Telegrams 1, 3, and 111)
| Signal | Description |
|---|---|
| STW2.0-STW2.11 | Reserved |
| STW2.12 | Master sign-of-life, bit 0 |
| STW2.13 | Master sign-of-life, bit 1 |
| STW2.14 | Master sign-of-life, bit 2 |
| STW2.15 | Master sign-of-life, bit 3 |
POS_STW1 Positioning Control Word (for Telegram 111)
| Signal | Description |
|---|---|
| POS_STW1.0 | Traversing blocks selection, bit |
| POS_STW1.1 | Traversing blocks selection, bit |
| POS_STW1.2 | Traversing blocks selection, bit |
| POS_STW1.3 | Traversing blocks selection, bit |
| POS_STW1.4 | Reserved |
| POS_STW1.5 | Reserved |
| POS_STW1.6 | Reserved |
| POS_STW1.7 | Reserved |
| POS_STW1.8 | 1 = Absolute positioning, 0 = Relative positioning |
| POS_STW1.9 | Absolute positioning, bit 0 |
| POS_STW1.10 | Absolute positioning, bit 1 |
| POS_STW1.11 | Reserved |
| POS_STW1.12 | 1 = Continuous transfer, 0 = Activate MDI block update with the rising edge of traversing blocks (STW1.6) |
| POS_STW1.13 | Reserved |
| POS_STW1.14 | 1 = Setting-up signal selected, 0 = Positioning signal selected |
| POS_STW1.15 | 1 = MDI selection |
POS_STW2 Positioning Control Word (for Telegram 111)
| Signal | Description |
|---|---|
| POS_STW2.0 | Reserved |
| POS_STW2.1 | Velocity limit activated |
| POS_STW2.2 | Reserved |
| POS_STW2.3 | Reserved |
| POS_STW2.4 | 1 = Axis moving forward, 0 = Axis not moving |
| POS_STW2.5 | 1 = Axis moving backward, 0 = Axis not moving |
| POS_STW2.6 | 1 = Negative soft limit switch reached |
| POS_STW2.7 | 1 = Positive soft limit switch reached |
| POS_STW2.8 | Reserved |
| POS_STW2.9 | Reserved |
| POS_STW2.10 | Reserved |
| POS_STW2.11 | Reserved |
| POS_STW2.12 | Reserved |
| POS_STW2.13 | Reserved |
| POS_STW2.14 | 1 = Activate the soft limit switch, 0 = Deactivate the soft limit switch |
| POS_STW2.15 | 1 = Activate the hard limit switch, 0 = Deactivate the hard limit switch |
Definitions of Status Words
ZSW1 Status Word (for Telegrams 1 and 3)
| Signal | Description |
|---|---|
| ZSW1.0 | 1 = Ready for switching on, 0 = Not ready for switching on |
| ZSW1.1 | 1 = Ready for operation, 0 = Not ready for operation |
| ZSW1.2 | 1 = Operation enabled, 0 = Operation disabled |
| ZSW1.3 | 1 = Fault present, 0 = No fault |
| ZSW1.4 | 1 = Coast-to-stop inactive, 0 = Coast-to-stop active |
| ZSW1.5 | 1 = Quick stop inactive, 0 = Quick stop active |
| ZSW1.6 | 1 = Inhibit switching on active, 0 = Inhibit switching on inactive |
| ZSW1.7 | 1 = Alarm present, 0 = No alarm |
| ZSW1.8 | 1 = Velocity error within tolerance, 0 = Velocity error exceeding tolerance |
| ZSW1.9 | 1 = Have control request, 0 = No control request |
| ZSW1.10 | 1 = Reference velocity reached or exceeded, 0 = Reference velocity not reached or exceeded |
| ZSW1.11 | Reserved |
| ZSW1.12 | Reserved |
| ZSW1.13 | Reserved |
| ZSW1.14 | Reserved |
| ZSW1.15 | Reserved |
ZSW1 Status Word (for Telegram 111)
| Signal | Description |
|---|---|
| ZSW1.0 | 1 = Ready for switching on, 0 = Not ready for switching on |
| ZSW1.1 | 1 = Ready for operation, 0 = Not ready for operation |
| ZSW1.2 | 1 = Operation enable, 0 = Operation disable |
| ZSW1.3 | 1 = Fault present, 0 = No fault |
| ZSW1.4 | 1 = Coast-to-stop inactive, 0 = Coast-to-stop active |
| ZSW1.5 | 1 = Quick stop inactive, 0 = Quick stop active |
| ZSW1.6 | 1 = Inhibit switching on active, 0 = Inhibit switching on inactive |
| ZSW1.7 | 1 = Alarm present, 0 = No alarm |
| ZSW1.8 | 1: Position following error within tolerance, 0: Position following error exceeding tolerance |
| ZSW1.9 | 1 = Have control request, 0 = No control request |
| ZSW1.10 | 1 = Target position reached, 0 = Target position not reached |
| ZSW1.11 | 1 = Reference point set, 0 = Reference point not set |
| ZSW1.12 | 0-1 rising edge: Positioning activated, movement task confirmed |
| ZSW1.13 | 1 = Drive stopped, 0 = Drive running |
| ZSW1.14 | 1 = Drive accelerating, 0 = Drive not accelerating |
| ZSW1.15 | 1 = Drive decelerating, 0 = Drive not decelerating |
ZSW2 Status Word (for Telegrams 1, 3, and 111)
| Signal | Description |
|---|---|
| ZSW2.0~ZSW2.9 | Reserved |
| ZSW2.10 | 1 = Pulses enabled |
| ZSW2.11 | Reserved |
| ZSW2.12 | Slave sign-of-life, bit 0 |
| ZSW2.13 | Slave sign-of-life, bit 1 |
| ZSW2.14 | Slave sign-of-life, bit 2 |
| ZSW2.15 | Slave sign-of-life, bit 3 |
POS_ZSW1 Status Word (for Telegram 111)
| Signal | Description |
|---|---|
| POS_ZSW1.0 | Traversing blocks bit 0 activated |
| POS_ZSW1.1 | Traversing blocks bit 1 activated |
| POS_ZSW1.2 | Traversing blocks bit 2 activated |
| POS_ZSW1.3 | Traversing blocks bit 3 activated |
| POS_ZSW1.4 | Reserved |
| POS_ZSW1.5 | Reserved |
| POS_ZSW1.6 | Reserved |
| POS_ZSW1.7 | Reserved |
| POS_ZSW1.8 | 1 = Negative hard limit activated, 0 = Negative hard limit not activated |
| POS_ZSW1.9 | 1 = Positive hard limit activated, 0 = Positive hard limit not activated |
| POS_ZSW1.10 | 1 = JOG mode activated, 0 = JOG mode not activated |
| POS_ZSW1.11 | 1 = Reference point approach activated, 0 = Reference point approach not activated |
| POS_ZSW1.12 | Reserved |
| POS_ZSW1.13 | 1 = Traversing blocks activated |
| POS_ZSW1.14 | Reserved |
| POS_ZSW1.15 | 1 = MDI activated, 0 = MDI not activated |
POS_ZSW2 Status Word (for Telegram 111)
| Signal | Description |
|---|---|
| POS_ZSW2.0 | Reserved |
| POS_ZSW2.1 | Velocity limit activated |
| POS_ZSW2.2 | Reserved |
| POS_ZSW2.3 | Reserved |
| POS_ZSW2.4 | 1 = Axis moving forward, 0 = Axis not moving |
| POS_ZSW2.5 | 1 = Axis moving backward, 0 = Axis not moving |
| POS_ZSW2.6 | 1 = Negative soft limit switch reached |
| POS_ZSW2.7 | 1 = Positive soft limit switch reached |
| POS_ZSW2.8 | Reserved |
| POS_ZSW2.9 | Reserved |
| POS_ZSW2.10 | Reserved |
| POS_ZSW2.11 | Reserved |
| POS_ZSW2.12 | Reserved |
| POS_ZSW2.13 | Reserved |
| POS_ZSW2.14 | Reserved |
| POS_ZSW2.15 | Reserved |
9. Troubleshooting
9.1. Troubleshooting Checklist

Reset Operation
- Set F31.00 (Fault reset) to 1 to stop displaying the fault on the panel.
- To reset resettable faults, switch off the S-ON signal first and then send the fault reset signal (set F31.00 to 1).
- To reset resettable alarms, eliminate the alarm source and then the servo drive automatically resets the alarms.
CAUTION
- Some faults/alarms can only be reset after the causes are rectified through setting modifications. However, a reset operation does not activate modifications.
- If the modification can be effective only after power-on, power on the device again.
- If the modification can be effective only after stop, turn off the S-ON signal. The servo drive can operate properly only after modifications are activated.
9.2. List of Faults and Alarms
List of Factory Fault Codes (Class 1)
| Fault Group | Fault Code | Fault Name | Bus Fault Code | Resettable |
|---|---|---|---|---|
| Class 1 | Er01.0 | Mismatch of software versions | 0x6100 | Non-resettable |
| Er01.1 | Mismatch of motor parameters | 0x7122 | Non-resettable | |
| Er02.0 | Product matching fault. No specified drive | 0x6100 | Non-resettable | |
| Er02.1 | Product matching fault. No specified motor | 0x6100 | Non-resettable | |
| Er02.2 | Product matching fault. No specified encoder | 0x6100 | Non-resettable | |
| Er03.0 | System parameter error | 0x6320 | Non-resettable | |
| Er03.1 | Parameter out-of-range | 0x6320 | Non-resettable | |
| Er03.2 | Parameter writing error | 0x6320 | Non-resettable | |
| Er03.3 | Parameter reading error | 0x6320 | Non-resettable | |
| Er04.0 | FPGA power-on check error | 0x6100 | Non-resettable | |
| Er04.1 | FPGA power-on not reset | 0x6100 | Non-resettable | |
| Er04.2 | FPGA transmission interrupted | 0x6100 | Non-resettable | |
| Er05.0 | Current loop timeout | 0x7500 | Non-resettable | |
| Er05.1 | Speed loop timeout | 0x7500 | Non-resettable | |
| Er05.2 | Position loop timeout | 0x7500 | Non-resettable | |
| Er06.0 | Protection from out of control | 0x8400 | Non-resettable | |
| Er10.0 | P-hardware overcurrent | 0x2312 | Non-resettable | |
| Er10.1 | N-hardware overcurrent | 0x2312 | Non-resettable | |
| Er10.2 | U phase software overcurrent | 0x2312 | Non-resettable | |
| Er10.3 | V phase software overcurrent | 0x2312 | Non-resettable | |
| Er10.4 | Output short circuited to ground | 0x2330 | Non-resettable | |
| Er10.5 | Current sampling failure | 0x6100 | Non-resettable | |
| Er10.6 | Incorrect current parameter setting | 0x6320 | Non-resettable | |
| Er10.7 | UV current correction failure | 0x6100 | Non-resettable | |
| Er10.8 | Excessive current zero drift | 0x6100 | Non-resettable | |
| Er10.9 | Current exception during enabling | 0x2312 | Non-resettable | |
| Er11.0 | Excessive motor speed upon servo drive power-on | - | Non-resettable | |
| Er11.1 | Drive over-temperature | 0x2312 | Non-resettable | |
| Er12.0 | PWM buffer detection failure | - | Non-resettable | |
| Er20.1 | Encoder internal fault | 0x7305 | Non-resettable | |
| Er20.2 | Encoder reading/writing error | 0x7305 | Non-resettable | |
| Er20.3 | Encoder data frame loss | 0x7305 | Non-resettable | |
| Er20.4 | Excessive encoder incremental position | 0x7305 | Non-resettable | |
| Er20.5 | Abnormal encoder data | 0x7305 | Non-resettable | |
| Er20.6 | Mismatch of encoder type | 0x7305 | Non-resettable | |
| Er20.7 | Encoder model not supported | 0x7305 | Non-resettable | |
| Er20.8 | Encoder battery failure | 0x7305 | Non-resettable | |
| Er20.9 | Encoder multi-turn error | 0x7305 | Non-resettable | |
| Er21.0 | Mismatch between encoder pulses per revolution and drive pulses per revolution | 0x7305 | Non-resettable | |
| Er22.0 | Second encoder disconnection | 0x7305 | Non-resettable | |
| Er32.8 | 200P parallel port check failure | - | Non-resettable | |
| Er32.9 | Mismatch between 200P version and MCU version | - | Non-resettable | |
| Er40.0 | Drive overload | 0x3230 | Resettable | |
| Er41.0 | Motor overload | 0x3230 | Resettable | |
| Er41.1 | Motor over-temperature due to locked-rotor | 0x7121 | Resettable | |
| Er41.2 | Motor over-temperature | 0x4210 | Resettable | |
| Er42.0 | IGBT temperature too high | 0x4210 | Resettable | |
| Er42.1 | Discharge tube temperature too high | 0x4210 | Resettable | |
| Er42.2 | Heatsink temperature too high | 0x4210 | Resettable | |
| Er43.0 | Overvoltage | 0x3210 | Resettable | |
| Er43.1 | Undervoltage | 0x3220 | Resettable | |
| Er45.0 | S-ON enabling failure | 0xFF00 | Resettable | |
| Er46.0 | Motor overspeed | 0x8400 | Resettable | |
| Er47.0 | Excessive position deviation | 0x8611 | Resettable | |
| Er47.1 | Position deviation overflow | 0x8611 | Resettable | |
| Er47.2 | Excessive fully closed-loop mixed deviation | 0x8611 | Resettable | |
| Er48.0 | STO status exception | 0x0480 | Resettable | |
| Er48.1 | STO buffer 5 V power fault | 0x0481 | Resettable | |
| Er48.2 | Optocoupler fault in STO pulse detection | 0x0482 | Resettable | |
| Er48.3 | STO buffer detection failure | 0x0483 | Resettable | |
| Er50.1 | D/Q current overflow | 0x6100 | Resettable | |
| Er51.0 | Offline inertia auto-tuning failure | 0x6310 | Resettable | |
| Er51.1 | Offline inertia parameter error | 0x6310 | Resettable | |
| Er52.0 | Angle auto-tuning failure | 0x7122 | Resettable | |
| Er53.0 | Motor parameter auto-tuning timeout | 0x7122 | Resettable | |
| Er53.1 | Resistance parameter auto-tuning failure | 0x7122 | Resettable | |
| Er53.2 | Inductance parameter auto-tuning failure | 0x7122 | Resettable | |
| Er53.3 | Back EMF parameter auto-tuning failure | 0x7122 | Resettable | |
| Er54.0 | Current loop auto-tuning failure | 0x7122 | Resettable | |
| Er55.0 | Excessive vibration | 0x7122 | Resettable | |
| Er80.0 | Control power undervoltage | 0x3120 | Resettable | |
| Er81.0 | Input phase loss 1 | 0x3130 | Resettable | |
| Er81.1 | Input phase loss 2 | 0x3130 | Resettable | |
| Er81.2 | Output phase loss | - | Resettable | |
| Er82.0 | DI function allocation fault | 0x6320 | Resettable | |
| Er82.1 | DO function allocation fault | 0x6320 | Resettable | |
| Er82.2 | VDI function allocation fault | 0xFF00 | Resettable | |
| Er82.3 | VDO function allocation fault | 0xFF00 | Resettable | |
| Er84.0 | Electronic gear ratio setting error | 0x6320 | Resettable | |
| Er84.1 | Software limit setting error | 0x6320 | Resettable | |
| Er84.2 | Encoder resolution setting error | 0x7122 | Resettable | |
| Er84.3 | Home position setting error | 0xFF00 | Resettable | |
| Er87.3 | Overflow of 32-bit sign bit of the target position during limiting | 0xFF00 | Resettable | |
| Er87.4 | Target position exceeding maximum value of mechanical single-turn position in rotating mode | 0xFF00 | Resettable | |
| ErA0.1 | Multi-turn overflow fault | 0x7305 | Resettable | |
| ErC2.1 | DSC cannot be used in non-IRT mode | - | Resettable | |
| ErC1.4 | Unreliable network cable connection, disconnected in network operating mode | - | Resettable | |
| ErC1.8 | Bus switched from operational to non-operational state | - | Resettable | |
| ErC1.1 | IRT synchronization lost | - | Resettable | |
| ErC1.2 | PN network switched to disconnected status when enabled | - | Resettable | |
| ErC2.3 | Network parameters cannot be set with network cable connected | - | Resettable |
List of Factory Alarm Codes (Class 3)
| Fault Group | Alarm Code | Alarm Name | Bus Fault Code | Resettable |
|---|---|---|---|---|
| Class 3 | ALF0.0 | Emergency stop alarm | 0xF00 | Resettable |
| ALF1.0 | Re-power-on required for parameter settings to take effect | 0x6320 | Resettable | |
| ALF1.1 | Frequent parameter storage alarm | 0x5530 | Resettable | |
| ALF1.2 | Torque reached parameter error | 0x6320 | Resettable | |
| ALF1.3 | Excessive parameter write frequency from the host controller | - | Resettable | |
| ALF2.0 | Forward overtravel alarm | 0x5443 | Resettable | |
| ALF2.1 | Reverse overtravel alarm | 0x5444 | Resettable | |
| ALF2.2 | Position limit warning in absolute linear mode | - | Resettable | |
| ALF4.0 | Homing timeout | 0x6320 | Resettable | |
| ALF4.1 | Homing DI conflict | 0x6320 | Resettable | |
| ALF4.2 | Homing mode conflict | 0x6320 | Resettable | |
| ALF5.0 | Braking resistor overload | 0x3210 | Resettable | |
| ALF5.1 | Too small resistance of external regenerative resistor | 0x6320 | Resettable | |
| ALF6.1 | Output phase loss | 0x3230 | Resettable | |
| ALF7.1 | Program block limit exceeded (PN) | - | Resettable | |
| ALF7.2 | MDI absolute position setpoint exceeding soft limit value (PN) | - | Resettable | |
| ALF8.0 | Vibration occurred during auto-tuning | 0x7122 | Resettable | |
| ALF9.0 | Encoder battery voltage low | 0x7305 | Resettable |
10. User Tips
No specific user tips were available from provided reviews or Q&A content. Always refer to the detailed instructions for optimal performance and safety.
11. Warranty and Support
For warranty information, technical support, or service inquiries, please contact STEPPERONLINE customer service or visit their official website. Ensure to have your product model and serial number ready for faster assistance.