Estardyn XL4015

Contents

Estardyn XL4015 DC-DC Step Down Buck Converter

Adjustable 4-38V to 1.25-36V Fixed Frequency Power Module

1. Introduction

The Estardyn XL4015 is a high-efficiency, non-isolated DC-DC step-down (buck) converter module. It is designed to convert a higher input voltage into a lower, adjustable output voltage with a maximum output current of 5A. This module is suitable for various applications requiring a stable and adjustable power supply, such as embedded systems, battery charging, and general electronic projects.

2. Specifications

Feature Specification
Module Properties Non-isolated constant current and voltage module
Rectification Non-synchronous rectification
Input Voltage 8V - 36V
Output Voltage 1.25V - 32V (Adjustable)
Output Current Adjustable, maximum 5A
Conversion Efficiency Up to 95%
Switching Frequency 180KHz
Output Ripple 50mV (max) 20M bandwidth
Load Regulation ± 0.5%
Voltage Regulation ± 2.5%
Operating Temperature -40°C to +85°C
Dimensions (L x W x H) 5.2 x 2.65 x 1.4 cm
Package Type SMD

3. Setup and Connections

Before connecting the module, ensure your power source and load are within the specified voltage and current ranges. Observe proper polarity to prevent damage.

  1. Identify Terminals: The module has clearly marked input and output terminals. 'IN+' and 'IN-' are for the input voltage, and 'OUT+' and 'OUT-' are for the output voltage.
    Bottom view of two XL4015 modules showing IN+ IN- and OUT+ OUT- terminals
    Figure 3.1: Bottom view of XL4015 modules, highlighting input and output terminals.
  2. Input Power Connection: Connect your DC power source to the 'IN+' (positive) and 'IN-' (negative) terminals. Ensure the input voltage is between 8V and 36V.
  3. Load Connection: Connect your load to the 'OUT+' (positive) and 'OUT-' (negative) terminals. Do not connect the load before adjusting the output voltage.
Top view of two XL4015 modules with components and adjustment potentiometers
Figure 3.2: Top view of XL4015 modules, showing main components and adjustment potentiometers.

4. Operating Instructions

  1. Voltage Adjustment: With the input power connected and no load attached, use a multimeter to measure the output voltage across 'OUT+' and 'OUT-'. Turn the potentiometer (the blue square component with a screw slot) clockwise to increase the output voltage and counter-clockwise to decrease it. Adjust until the desired output voltage (between 1.25V and 32V) is achieved.
    Close-up top view of an XL4015 module, highlighting the blue potentiometers for adjustment
    Figure 4.1: Close-up of an XL4015 module, showing the potentiometers for voltage/current adjustment.
  2. Current Adjustment (if applicable): If your module includes a current limit adjustment (typically a second potentiometer), you can set the maximum output current. This is usually done by shorting the output (briefly, with a current meter in series) and adjusting the current potentiometer to the desired limit. Exercise caution during this step.
  3. Connect Load: Once the desired output voltage (and current limit) is set, disconnect the input power, connect your load, and then reapply input power.

Caution: Always verify the output voltage with a multimeter before connecting your sensitive load to prevent damage.

5. Maintenance

  • Keep the module clean and free from dust and debris. Use a soft, dry brush or compressed air for cleaning.
  • Ensure adequate ventilation, especially when operating at higher currents, to prevent overheating.
  • Avoid exposing the module to moisture, extreme temperatures outside its operating range (-40°C to +85°C), or corrosive environments.
  • Regularly check connections for tightness and signs of wear or corrosion.

6. Troubleshooting

  • No Output Voltage:
    • Check input power supply: Ensure it is connected correctly and providing voltage within the 8V-36V range.
    • Verify polarity: Incorrect input polarity can damage the module.
    • Check for short circuits: Ensure there are no accidental shorts on the output or input terminals.
  • Output Voltage is Incorrect/Unstable:
    • Adjust the potentiometer: Slowly turn the voltage adjustment potentiometer to set the desired output.
    • Check load: Ensure the load is not drawing excessive current, which could cause voltage drop.
    • Input voltage fluctuations: Ensure the input voltage is stable.
  • Module Overheating:
    • Reduce load current: Operating close to the maximum 5A without adequate heat sinking can cause overheating.
    • Improve ventilation: Ensure proper airflow around the module.
    • Consider a heatsink: For continuous operation at higher currents, a heatsink may be necessary.

7. User Tips

  • For applications requiring more than 3A output current, it is highly recommended to add a heatsink to the main IC (XL4015) to ensure stable and long-term operation.
  • When adjusting the output voltage, use a small screwdriver and turn the potentiometer slowly. It may take several turns to see a significant change in voltage.
  • Always use a multimeter to verify the output voltage before connecting any sensitive electronic components.

8. Warranty and Support

For any technical assistance, questions, or issues not covered in this manual, please contact the seller or manufacturer directly. Keep your purchase records for reference.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.