Estardyn 3.12 TFT

Contents

Estardyn 3.12 Inch SSD1322 OLED Display Module 256x64 User Manual

Model: 3.12 TFT

1. Introduction

This manual provides detailed instructions for the Estardyn 3.12 Inch SSD1322 OLED Display Module. This high-resolution display features a 256x64 pixel matrix, offering clear visuals for various embedded applications. It supports both SPI and I2C communication interfaces, making it versatile for integration with microcontrollers such as STM32. The module comes with pre-soldered pin headers for ease of use.

Estardyn 3.12 Inch OLED Display Modules in various colors
Figure 1: Estardyn 3.12 Inch SSD1322 OLED Display Modules (various colors)
Front and back view of the Estardyn 3.12 Inch OLED Display Module
Figure 2: Front and back view of the OLED Display Module

2. Specifications

The following table details the key specifications of the Estardyn 3.12 Inch SSD1322 OLED Display Module:

Product parameters and pin definition table for the OLED module
Figure 3: Product Parameters and Pin Definition
Parameter Value
Size 3.12 inches
Resolution 256x64
Drive IC SSD1322
Interface Type 8-bit parallel / SPI
Display Color White, Blue, Green, Yellow (SKU dependent)
Power Supply 3.3V-5V
Screen Size (mm) 88 x 27.8 x 2
Module Size (mm) 100.5 x 33.5 x 6.3
Working Temperature -20°C ~ 70°C
Linking Method COG
Display Area (mm) 76.78 x 19.18

3. Pin Definition

The module features a 16-pin header. The function of each pin is described below:

PIN Symbol Function
1 VSS Grounding rod
2 VBAT Power pad
3 NC Empty feet (No Connection)
4~11 DB0~DB7 8-bit data bus (for 8-bit parallel interface)
12 /RD Enable the disabled selection pin (Read signal)
13 /WR Write Selection Pin (Write signal)
14 DC Data/Command control pin
15 /RESET Display screen reset terminal (Active Low)
16 /CS Chip Select signal (Active Low)

4. Physical Dimensions

The module's physical dimensions are critical for integration into your projects. Refer to the diagram below for detailed measurements.

Technical drawing showing the dimensions of the OLED module
Figure 4: Module Dimensions (Units in mm)
  • Overall Length: 100.5 ± 0.2 mm
  • Overall Width: 33.5 ± 0.2 mm
  • Viewing Area (V.A.): 78.8 mm x 28.54 mm
  • Active Area (A.A.): 76.78 mm x 19.18 mm
  • Pin Pitch: 2.54 mm

5. Setup and Connection

This OLED module supports both SPI and I2C communication protocols. Ensure your microcontroller (e.g., STM32) is configured to use the correct interface.

5.1. Power Connection

  • Connect the VSS pin to your system's Ground (GND).
  • Connect the VBAT pin to a 3.3V to 5V power supply. Ensure the voltage is within the specified range to prevent damage.

5.2. SPI Interface Connection

For SPI communication, connect the following pins to your microcontroller:

  • /CS (Chip Select)
  • DC (Data/Command)
  • /RESET (Reset)
  • DB0-DB7 (MOSI, MISO, SCK - specific pins depend on your microcontroller's SPI configuration)
  • /RD and /WR pins are typically tied high or low depending on the specific SPI mode and library used, or left unconnected if not used.

5.3. I2C Interface Connection

For I2C communication, connect the following pins to your microcontroller:

  • SDA (Data Line) - typically one of the DB pins, check module schematic for exact mapping.
  • SCL (Clock Line) - typically one of the DB pins, check module schematic for exact mapping.
  • /RESET (Reset)
  • /CS and DC pins may need to be tied to specific logic levels (e.g., VCC or GND) to enable I2C mode, depending on the module's design. Consult the SSD1322 datasheet for detailed I2C configuration.

Note: Always refer to the specific wiring diagram or datasheet provided with your module for the exact pin configuration and mode selection (SPI/I2C) as it may vary slightly between revisions.

6. Basic Operation

Once connected, you will need to initialize the SSD1322 controller and send display data. This typically involves:

  1. Initialization: Send a sequence of commands to the SSD1322 controller to set up display parameters such as contrast, display mode, and memory addressing.
  2. Clearing the Display: Fill the display memory with zeros to ensure a blank screen before drawing.
  3. Drawing Graphics/Text: Send pixel data or character bitmaps to the display memory. Libraries for common microcontrollers (e.g., Adafruit GFX for Arduino/ESP32, various STM32 HAL/LL libraries) can simplify this process.
  4. Display Update: The SSD1322 automatically refreshes the display based on the content of its internal GRAM (Graphics RAM).

Example code and libraries for popular microcontrollers are widely available online and can significantly accelerate development.

7. Care and Maintenance

  • Handling: Handle the module by its edges to avoid touching the display surface or components.
  • Cleaning: Use a soft, lint-free cloth, slightly dampened with distilled water or isopropyl alcohol, to gently clean the display surface. Avoid abrasive materials or harsh chemicals.
  • Storage: Store the module in an anti-static bag in a dry, cool environment, away from direct sunlight and extreme temperatures.
  • Power Supply: Always ensure the power supply voltage is within the 3.3V-5V range. Over-voltage can permanently damage the OLED panel and controller.
  • Static Electricity: OLED modules are sensitive to electrostatic discharge (ESD). Always use proper ESD precautions when handling the module.

8. Troubleshooting

8.1. Display Not Lighting Up

  • Check Power: Verify that VSS is connected to GND and VBAT receives the correct voltage (3.3V-5V).
  • Initialization Sequence: Ensure the SSD1322 controller is correctly initialized with the proper command sequence.
  • Reset Pin: Confirm the /RESET pin is correctly toggled or held high/low as required by your setup.
  • Interface Connection: Double-check all SPI/I2C connections for continuity and correct pin mapping.

8.2. Incorrect or Garbled Display

  • Data Format: Ensure the data sent to the display matches the expected format (e.g., pixel order, color depth).
  • Communication Protocol: Verify that your microcontroller's communication (SPI/I2C) settings match the module's configuration (e.g., SPI mode, I2C address).
  • Buffer Size: If using a display buffer, ensure it matches the 256x64 resolution and is correctly mapped to the display memory.

8.3. Partial Display or Missing Pixels

  • Connection Issues: Inspect for loose connections or cold solder joints on the data lines.
  • Software Addressing: Confirm that your code is addressing the entire 256x64 display area and not just a portion.

9. User Tips

  • Use Libraries: For faster development, leverage existing open-source libraries for SSD1322 OLED displays with your chosen microcontroller platform (e.g., Arduino, ESP-IDF, STM32Cube).
  • Power Consumption: OLED displays can consume significant power, especially when displaying bright images. Consider power management in battery-powered applications.
  • Burn-in Prevention: While OLEDs are generally robust, prolonged display of static images can lead to burn-in. Implement screen savers or pixel shifting if your application requires static content for extended periods.
  • Contrast Adjustment: Experiment with the contrast settings in the SSD1322 controller to achieve optimal readability for your specific application and lighting conditions.

10. Warranty and Support

Estardyn products are manufactured to high-quality standards. For any technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact your retailer or the Estardyn customer support team. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.