TODIMART T3

Contents

TODIMART T3 Electric Scooter User Manual

Model: T3 (also T3S, T6, T6S)

1. Safety Instructions

IMPORTANT SAFETY WARNINGS:

  • Fire Risk: Please mind potential fire risk and strictly follow the instruction manual for charging and storage.
  • Protective Equipment: While using the product, please wear protective equipment (helmet, elbow pads, knee pads, wrist guards) and fully comply with the applicable law and regulations.
  • Water Sources: Never use the product close to a water source.
  • Damage: Stop using the product if it is damaged.
  • Authorized Spaces: Never use the product outside of spaces authorized by regulations.
  • Mechanical Wear: As with all mechanical appliances, a vehicle is subject to considerable stresses and wear. Different materials and components react differently to wear or fatigue. If a component's expected lifespan is exceeded, it can break suddenly, causing injury. Cracks, scratches, or discoloration on highly stressed areas indicate the component's lifespan has been exceeded and it should be replaced.
  • Kickstand Stability: The kickstand does not ensure the stability of the scooter if used on unstable or sloping terrain.
  • Hot Components: The motor and brake can get hot during use. Do not touch them after use to avoid any risk of burns.

Conditions of Use:

  • Before use, read these instructions carefully and keep them for future reference. Ensure your scooter is in perfect working order.
  • This scooter is designed for leisure use. Familiarize yourself with local regulations before use.
  • Designed for users aged 16-50 years old, if local regulations allow.
  • Before each use, ensure all locking devices are properly engaged, the steering system is correctly adjusted, and all connection elements are properly tightened and not broken.
  • Check brake function before each use.
  • Regularly check wheel and bearing quality and maintenance. Remove any sharp edges.
  • Ensure all screws are tight, as self-tightening nuts and other fasteners may become compromised.
  • Most serious accidents occur in the first months of use; take time to learn the basics of scooter riding.
  • Avoid busy places with heavy traffic.
  • Ride on flat, clean, dry surfaces, away from other road users if possible.
  • Do not modify or transform the vehicle, including the steering tube, sleeve, stem, folding mechanism, and rear brake.
  • Do not carry bags or other objects on the front of the scooter.
  • The vehicle is intended for one person only.
  • Do not use accessories or additional items not approved by the manufacturer.
  • Sound pressure level of A-weighted emissions does not exceed 70 dB (A).
  • Any load attached to the handlebar will affect vehicle stability.
  • This vehicle is not intended for acrobatic use.
  • The motor activates when scooter speed is above 3 km/h.
  • Any braking action turns off the assistance.
  • Wait for the scooter to come to a complete stop before dismounting.
  • Control your speed and trajectory to maintain control.
  • The scooter can be used in free-wheel mode when electric assistance is turned off.
  • Braking distances may extend in wet weather.
  • Notify pedestrians or cyclists of your presence if they haven't seen or heard you.
  • Traffic in the city has many obstacles (curbs, steps). Avoid jumping obstacles. Anticipate and adapt your trajectory and speed. Dismount if obstacles become dangerous.
  • Walk across protected passages.
  • Do not ride in the rain or through puddles.
  • Do not accelerate when going downhill.
  • Do not press the accelerator when walking alongside the scooter.
  • Lock the rear wheel with a padlock when parked to prevent misuse.
  • Avoid obstacles.
  • Do not hang heavy items on the handlebar.
  • Keep both feet on the deck at all times.
  • Maintain 5-10 km/h over speed bumps, elevator door sills, bumpy roads; slightly bend knees to adjust.
  • Do not attempt dangerous actions.
  • Do not ride in traffic lanes or residential areas where vehicles and pedestrians are both allowed.
  • Do not turn the handlebar violently during high-speed riding.
  • Do not ride with anyone else, including children.
  • Do not keep your feet on the rear mudguard.
  • Do not touch the disc brake.
  • Do not keep your hands away from the handlebar.
  • Do not try riding up or down stairs or jumping over obstacles.

2. Product Overview

The TODIMART T3 Electric Scooter is a high-performance, foldable e-scooter designed for urban mobility and leisure. It features smart control via a dedicated app, a powerful 250W brushless motor, and an 8.5-inch runflat solid tire for various road conditions.

Component Diagram

TODIMART T3 Electric Scooter component diagram showing speed display, high-bright headlight, cruise control, battery level display, and 3 speed modes (10, 20, 25 KM/H).

Diagram of the scooter's handlebar and display, highlighting the speed display, high-bright headlight, cruise control, battery level display, and three speed modes.

Detailed view of TODIMART T3 Electric Scooter features: ultra-bright headlights, red taillights when braking, and maintenance-free solid tires.

Detailed view of the scooter's lighting system and maintenance-free solid tires.

Accessories

  • Hexagon Spanner
  • Power Adapter
  • Screws (x4)

Please check carefully whether the package contents are complete and in good condition upon unboxing.

3. Assembly and Setup

  1. Fasten Handlebar Stem: Fasten the handlebar stem onto the headset. Ensure the kickstand is down for stability.
  2. Attach Handlebar: Attach the handlebar to the stem.
  3. Tighten Screws: Tighten the screws on both sides of the stem using the provided hexagon wrench.
  4. Function Check: After assembly, press the power button to check if the scooter is working properly.

4. Operation (How to Ride)

Control Panel and Power Switch

TODIMART T3 Electric Scooter smart travel integrated Bluetooth display showing speed, fashion screen, battery indicator, and ignition switch.

Smart travel integrated Bluetooth display with speed, battery, and ignition switch.

  • Speed Display: Shows current running speed in km/h.
  • Mode Display: The green light indicates low speed mode (max 15 km/h). Double-press the switch to change to high speed mode (red light, max 20 km/h).
  • Battery Indicator: Four electric lights indicate battery level. Lights extinguish from right to left as battery drains. Recharge when all lights are off.
  • Power Switch: Short press to turn on/off the light. Long press (2 seconds) to turn the scooter off.

Riding Instructions

  1. Turn On: Turn on the scooter and check the power indicator.
  2. Start Riding: Step on the deck with one foot, and slowly kick off with the other foot on the ground. Once the scooter starts to coast, place both feet on the deck and press the accelerator. The accelerator initiates once the coasting speed exceeds 5 km/h.
  3. Restarting: When the scooter is at a full stop, the accelerator automatically turns off. To restart, repeat step 2.
  4. Braking: Release the accelerator, and the Kinetic Energy Recovery System (KERS) will automatically initiate slow braking. Squeeze the brake lever for a sudden stop.
  5. Turning: Tilt your body in the steering direction as you turn, and slowly turn the handlebar.

Folding and Carrying

Image showing 3 easy steps to fold the TODIMART T3 Electric Scooter, with dimensions (108 cm length, 49 cm height when folded) and net weight (<12 kg).

Folding mechanism and dimensions for easy travel.

  1. Folding: Ensure the electric scooter is turned off. The walking function will open by folding the standpipe. Open the folded plate, align the fender, and check the position of the hook.
  2. Unfolding: To unfold, press the point of the hook to detach it from the fender. Straighten the vertical folded plate until it locks into place.
  3. Carrying: The folded scooter can be carried by holding the standpipe with one or both hands.

Product Video

Video demonstrating the features and operation of the TODIMART T3 Electric Scooter, including riding, display, lights, and folding.

5. Battery and Charging

Battery Information

Diagram showing the internal structure of the high-capacity 36V battery within the scooter deck.

Internal view of the high-capacity 36V battery.

  • The built-in 36V 280.8Wh high-quality lithium-ion battery offers a range of 20-40 km (typical 30-35 km under certain conditions).
  • Cruise control helps optimize power consumption.
  • Storage: If the scooter is not used for more than 30 days, fully charge the battery and store it in a dry, cool place. Recharge every 60 days to prevent potential damage.
  • Temperature: Do not leave the scooter or battery in environments above 45°C or below -20°C for extended periods (e.g., in a car under direct sunlight).
  • Disposal: Do not throw the battery into fire, as it may lead to battery failure, overheating, or fire. At the end of its life, return the battery to a store or authorized recycling center.

Charging Instructions

  • Switch off the scooter before charging.
  • Always charge indoors.
  • For optimal use, perform a full charge followed by a full discharge once a month.
  • Use only the original removable power supply unit supplied with the device.
  • The external flexible cable of the transformer cannot be replaced; if the cord is damaged, the transformer should be discarded.
  • Charging must be done in the presence of a user and under supervision.
  • Ensure the charger is compatible with your local electricity network (100-240V, 50-60Hz).

Charging Steps:

  1. Open the rubber stopper on the charging port.
  2. Plug in the charger.
  3. After charging, tighten the rubber stopper.

6. Daily Care and Maintenance

Regular maintenance helps keep your scooter in good condition, minimizes breakdowns, and extends its service life.

Cleaning and Storage

  • Cleaning: Wipe stains on the scooter's body with a damp cloth. For stubborn stains, apply toothpaste and brush with a toothbrush, then wipe clean. For scratches on plastic parts, use sandpaper or other abrasive materials to polish them.
  • Do NOT use: Alcohol, gasoline, kerosene, or other corrosive/volatile chemical solvents. Do not wash with high-pressure water spray.
  • During Cleaning: Ensure the scooter is turned off, the charging cable is unplugged, and the rubber flap is closed to prevent water leakage, which could cause electric shock or other problems.
  • Storage: When not in use, store the scooter indoors in a dry and cool place. Avoid prolonged outdoor exposure, excessive sunlight, overheating, and overcooling, as these can accelerate tire aging and compromise the scooter and battery lifespan.

Lubrication

  • Lubricate the folding mechanism and wheel bearings every 3 months with a silicone-based lubricant.

Component Adjustment

  • Regularly check and tighten all screws/bolts to manufacturer torque specifications (e.g., 10-15 Nm for the handlebar).
  • Do not make any modifications not noted in the manufacturer's instructions.

Adjusting the Disc Brake

To adjust the disc brake, use an M4 hexagon wrench:

  • If the brake is too tight: Loosen the screws on the caliper, slightly pull the brake cable to shorten the exposed length, then tighten the screws.
  • If the brake is too loose: Loosen the screws, slightly pull the brake cable to lengthen the exposed length, then tighten the screws.

7. Troubleshooting

If you encounter issues with your TODIMART T3 Electric Scooter, please refer to the following common troubleshooting steps:

  • Scooter Not Turning On: Ensure the battery is charged. Check all connections for looseness. If the issue persists, contact customer support.
  • Loss of Power/Reduced Range: Check battery indicator. Ensure the battery is fully charged. Extreme temperatures can affect battery performance. If the battery is old, it might need replacement.
  • Brake Issues: If brakes feel too loose or too tight, refer to the "Adjusting the Disc Brake" section in Daily Care and Maintenance. Ensure brake cables are not frayed or damaged.
  • Unusual Noises: Inspect wheels, bearings, and folding mechanism for any loose parts or debris. Lubricate as per maintenance instructions.
  • App Connectivity Issues: Ensure Bluetooth is enabled on your device and the scooter is powered on. Try restarting both the app and the scooter.

For more complex issues, please contact customer support.

8. Specifications

FeatureSpecification
Model NumberT3 (T3S, T6, T6S)
CategoryTwo-wheel Scooter
Applicable PeopleUnisex (Age 14-50 years old, Height 120-200 cm)
Dimensions (Unfolded)1080mm (L) x 430mm (W) x 1120mm (H)
Dimensions (Folded)1080mm (L) x 430mm (W) x 490mm (H)
Net Weight11.8 kg
Max Load Capacity120 kg
Max Speed25 km/h
Range Per Charge20-40 km (typical 30-35 km)
Climbing Ability15°
Tire Size8.5 inch (Maintenance-free solid tires)
Motor Power250W (Brushless motor)
Voltage36V
Battery Capacity7.8Ah (280.8Wh)
Max Charging Voltage42V DC
Charging TimeAbout 3-6 hours
Charger Input Voltage110-210V AC
Charger Output Voltage42V DC
Charger Rated Current1.5A
Operating Temperature-10°C to 40°C
Storage Temperature-20°C to 45°C
Protection LevelIP54
CertificationCE, CCC, ROSH (EN 17128:2020 PLEV Class 2)

9. User Tips

  • Pre-Ride Check: Always perform a quick check of all screws, connections, and brake functionality before each ride to ensure everything is secure.
  • Safety First: Never compromise on safety. Always wear a helmet and other protective gear, especially when riding in new environments or at higher speeds.
  • Battery Care: For optimal battery life and performance, ensure the battery is fully charged before long journeys and follow the recommended charging and storage guidelines.
  • Local Regulations: Familiarize yourself with and adhere to all local laws and regulations regarding electric scooter usage in your area.
  • Smooth Riding: The solid tires provide a maintenance-free experience. For a smoother ride over uneven surfaces, slightly bend your knees to absorb shocks.

10. Warranty and Support

The TODIMART T3 Electric Scooter comes with a reliable 1-Year Manufacturer Warranty. This warranty covers hardware malfunctions of the motor, battery, and lighting components. If you encounter any such issues within 12 months of purchase, you are eligible for free repair or replacement service.

TODIMART T1 kids electric scooter with 12 months manufacturer warranty for hardware malfunctions of motor, battery, lighting, offering free repair or replacement service.

Reliable 1-Year Warranty Service Included.

Customer Support

For any questions or support, please contact us:

Please always refer to the product packaging for any possible future after-sale shipping information.

11. Compliance and Recycling

Disclaimer

Please mind potential fire risk and strictly follow the instruction manual for charging and storage. While using the product, please wear protective equipment and fully comply with the applicable law and regulations.

WEEE and Battery Recycling Information

Correct Disposal of this product: This marking indicates that this product should not be disposed of with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling.

Battery Recycling Information for the European Union: Batteries or packaging for batteries are labeled in accordance with European Regulation EU 2023/1542 concerning batteries and accumulators and waste batteries and accumulators. This Regulation determines the framework for the return and recycling of used batteries and accumulators as applicable throughout the European Union. This label is applied to various batteries to indicate that the battery is not to be thrown away, but rather reclaimed upon end of life per this Regulation.

In accordance with the European Regulation EU 2023/1542, batteries and accumulators are labeled to indicate that they are to be collected separately and recycled at end of life. The label on the battery may also include a chemical symbol for the metal concerned in the battery (Pb for lead, Hg for mercury, and Cd for cadmium). Users of batteries and accumulators must not dispose of batteries and accumulators as unsorted municipal waste, but use the collection framework available to customers for the return, recycling, and treatment of batteries and accumulators. Customer participation is important to minimize any potential effects of batteries and accumulators on the environment and human health due to the potential presence of hazardous substances. Before placing electrical and electronic equipment (EEE) in the waste collection stream or in waste collection facilities, the end user of equipment containing batteries and/or accumulators must remove those batteries and accumulators for separate collection.

EC Declaration of Conformity

Hereby, Zhejiang Yuyou Technology Co., Ltd. declares that the Electric Scooter T3 is in compliance with Directive 2006/42/EU Machinery Directive.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.