1. Introduction
The GODIAG GT100 PLUS GPT is a versatile testing platform designed for automotive diagnostics and ECU maintenance. It facilitates OBDII protocol communication detection, ECU maintenance, diagnosis, programming, and coding. The device features a voltage and current display, providing real-time feedback on the ECU's operational status, which is crucial for maintenance engineers.
This tool converts the car's OBD2 interface into a 16-pin connector for signal detection, allowing connection to single or multiple vehicle modules. It can also be used with any diagnostic tool to verify vehicle communication integrity. Additionally, it supports 24V to 12V voltage conversion for heavy-duty trucks, DOIP-ENET communication, and GPT for reading and writing ECU data. A key function is its ability to supply power to the vehicle during battery changes, preventing data loss, automatic locking, remote control failure, and fault light activation.

Figure 1: GODIAG GT100 PLUS GPT device front view.
Video 1: Overview of the GODIAG GT100 PLUS GPT features and functions.
2. Key Features
- OBDII Protocol Communication Detection
- ECU Connection and Communication Status Display
- Ability to Connect Multiple ECUs
- Power Supply for Vehicle during Battery Replacement
- Includes Various Extension Cables
- OBD1 to OBD2 Diagnostic Interface Conversion
- Truck Diagnostic Interface Conversion to OBD2
- Dedicated Adapter for Future Use (coming soon)
- 24V to 12V Voltage Conversion for Heavy Duty Trucks
- DOIP-ENET Communication Support
- GPT (Generic Programming Tool) for ECU Data Read/Write
- Voltage and Current Display for Real-time Monitoring
- CANH and CANL shielded twisted cables for stable communication and electromagnetic interference resistance.

Figure 2: Visual representation of the GODIAG GT100 PLUS GPT's key functionalities.
3. Package Contents
Please verify that all items listed below are included in your package:
- 1x GODIAG GT100 PLUS GPT Host
- 1x GPT connecting cable
- 1x Ethernet cable
- 1x OBD 2-in-1 extension cable
- 1x Colored jumper cable
- 1x Power supply 12V
- 1x Resistance 120 ohm
- 6x Banana plugs
- 24x Wire accessories (Dupont 2.54mm connector female pins)
- 1x User Manual

Figure 3: Complete package contents of the GODIAG GT100 PLUS GPT.
4. Setup Instructions
4.1 Initial Connection to Vehicle OBDII Port
- Locate the vehicle's OBDII diagnostic port, typically found under the dashboard on the driver's side.
- Connect the OBD 2-in-1 extension cable to the vehicle's OBDII port.
- Connect the other end of the OBD 2-in-1 extension cable to the "Car Connect" port on the GODIAG GT100 PLUS GPT host.
- If external power is required, connect the 12V power supply to the "DC (12V)" input on the GT100 PLUS.
- Observe the voltage and current display on the GT100 PLUS to ensure proper power and communication.
4.2 Connecting to an ECU for Bench Operations
For bench programming or diagnosis, the GT100 PLUS can be connected directly to an ECU module.
- Identify the necessary pins on the ECU for power, ground, and communication (e.g., CAN H, CAN L, K-Line).
- Use the colored jumper cables and Dupont pins to connect the ECU to the corresponding banana plug ports on the "ECU Connector" section of the GT100 PLUS. Ensure correct polarity and pin assignments.
- Connect the 12V power supply to the "DC (12V)" input on the GT100 PLUS to power the ECU.
- If connecting to a diagnostic tool or laptop, use the appropriate cables (e.g., OBDII cable to a diagnostic tool, Ethernet cable for DOIP).

Figure 4: General setup for connecting the GT100 PLUS GPT to an ECU and a laptop.
5. Operating Instructions
5.1 OBDII Protocol Communication Detection
When connected to the vehicle's OBDII port, the GT100 PLUS can detect and display the communication status. The integrated voltage and current display helps in monitoring the health of the OBDII communication lines.
- Connect the GT100 PLUS to the vehicle's OBDII port as described in Section 4.1.
- Turn the vehicle's ignition to the ON position (engine off).
- Observe the LEDs on the GT100 PLUS corresponding to the OBDII pins (e.g., CAN H, CAN L, K-Line) to confirm active communication. The voltage and current display will show the power status.
- Connect your diagnostic scanner to the GT100 PLUS's OBDII port to perform diagnostics.

Figure 5: Connecting the GT100 PLUS GPT for OBDII diagnosis with a diagnostic tool.
5.2 ECU Maintenance, Diagnosis, Programming, and Coding
The GT100 PLUS acts as a breakout box and power supply for ECU operations.
- Set up the ECU connection as described in Section 4.2.
- Ensure the ECU is receiving stable power, as indicated by the voltage and current display.
- Connect your ECU programming or diagnostic tool to the GT100 PLUS (either via OBDII port or direct pin connections using jumper cables).
- Perform desired operations such as reading/writing data, coding, or diagnosis using your specialized software/tool.

Figure 6: ECU programming setup using the GT100 PLUS GPT and a laptop.
5.3 24V to 12V Voltage Conversion for Heavy Duty Trucks
The GT100 PLUS can convert 24V vehicle power to 12V for compatible diagnostic tools.
- Connect the GT100 PLUS to the 24V heavy-duty truck's diagnostic port using the appropriate OBD2 cable.
- Ensure the 24V to 12V conversion function is activated (if applicable, refer to the device's specific switch or mode).
- Connect your 12V diagnostic tool to the GT100 PLUS's OBDII port. The GT100 PLUS will supply the converted 12V power to the diagnostic tool.

Figure 7: Setup for 24V to 12V conversion for heavy-duty truck diagnostics.
5.4 DOIP-ENET Communication
The device supports DOIP-ENET communication for modern vehicles.
- Connect the GT100 PLUS to the vehicle's OBDII port.
- Connect the Ethernet cable from the GT100 PLUS to your laptop or diagnostic device that supports ENET communication.
- Important Note: Users cannot connect to the GT100 PLUS GPT host when using the ENET function directly. The ENET connection is typically between the vehicle's OBDII port (via GT100 PLUS) and the diagnostic software on a laptop.

Figure 8: DOIP ENET connection setup for vehicle diagnostics.
5.5 GPT (Generic Programming Tool) for ECU Data Read/Write
The GPT function allows for advanced ECU data manipulation.
- Connect the ECU to the GT100 PLUS using the GPT connecting cable and jumper wires as per the ECU's specific pinout for GPT.
- Ensure the GT100 PLUS is powered and the ECU is correctly connected.
- Connect your GPT compatible programming tool or software to the GT100 PLUS.
- Follow the instructions of your GPT software to read or write data to the ECU.

Figure 9: GPT connection setup for reading and writing ECU data.
5.6 Power Supply During Battery Change
To prevent data loss during battery replacement:
- Connect the GT100 PLUS to the vehicle's OBDII port.
- Connect the 12V power supply to the "DC (12V)" input on the GT100 PLUS.
- Ensure the GT100 PLUS is powered ON. This will provide continuous power to the vehicle's control modules while the main battery is disconnected and replaced.
6. Maintenance
- Cleaning: Use a soft, dry cloth to clean the device. Do not use abrasive cleaners or solvents.
- Storage: Store the device and its accessories in a cool, dry place, away from direct sunlight and extreme temperatures.
- Cable Care: Inspect all cables regularly for signs of wear or damage. Replace any damaged cables immediately to ensure safe and reliable operation.
- Connector Care: Keep all connectors clean and free from dust or debris.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No power to GT100 PLUS | Loose power connection; Faulty power supply; Vehicle's OBDII port not supplying power. | Check all power connections. Ensure the 12V power supply is working. Verify the vehicle's OBDII port is active. |
| No communication with ECU/Vehicle | Incorrect wiring; Damaged cables; ECU/Vehicle communication lines faulty; Incorrect protocol selected by diagnostic tool. | Double-check all wiring connections, especially pin assignments for ECU. Inspect cables for damage. Ensure the diagnostic tool is configured for the correct communication protocol. |
| Voltage/Current display shows abnormal readings | Short circuit; Overload; Faulty ECU/Vehicle electrical system. | Immediately disconnect the device. Check for short circuits in wiring. Verify the health of the ECU or vehicle's electrical system. |
| DOIP-ENET connection issues | Incorrect Ethernet cable; Software configuration issues; GT100 PLUS not properly connected to vehicle. | Ensure a standard Ethernet cable is used. Verify laptop/software ENET settings. Confirm GT100 PLUS is correctly connected to the vehicle's OBDII port. |
8. Specifications
| Feature | Detail |
|---|---|
| Product Name | GODIAG GT100 PLUS GPT ENET DOIP OBD II Break Out Box ECU Connector |
| Brand | GODIAG |
| Model | GT100 PLUS GPT ENET DOIP |
| Input Voltage | 12V DC (via external power supply) |
| Vehicle Compatibility | OBDII compliant vehicles, 24V heavy-duty trucks (with conversion) |
| Communication Protocols | OBDII, DOIP-ENET, GPT |
| Dimensions (Host) | Approx. 23cm (Length) x 20cm (Width) x 10cm (Height) |
| Weight | Approx. 1.5 kg |
| Cable Type | CANH and CANL shielded twisted cables |
9. User Tips
- Always ensure all connections are secure before powering on the device or performing any diagnostic/programming tasks.
- When working with ECUs on the bench, double-check the ECU's pinout diagram to avoid incorrect wiring, which could damage the ECU or the GT100 PLUS.
- For critical operations like ECU programming, ensure a stable power supply to both the GT100 PLUS and the ECU to prevent interruptions.
- Keep the included manual handy for quick reference on pin assignments and connection diagrams.
10. Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the documentation provided with your purchase or contact the manufacturer/seller directly. Ensure you retain your proof of purchase for any warranty claims.