HOBBYWING XERUN V10 G5

Contents

HOBBYWING XERUN V10 G5 Sensored Brushless RC Racing Motor User Manual

Model: XERUN V10 G5 | Brand: HOBBYWING

1. Introduction

The HOBBYWING XERUN V10 G5 is a high-performance sensored brushless motor designed for 1/10 and 1/12 scale RC model car racing. Built with superior materials and advanced engineering, it offers enhanced power, efficiency, and tunability for competitive racing. This manual provides essential information for the proper setup, operation, and maintenance of your motor.

2. Safety Precautions

Always observe the following safety guidelines to prevent injury or damage to the product and surrounding equipment:

  • Ensure all connections are secure and correctly polarized before applying power.
  • Avoid touching the motor during or immediately after operation, as it can become very hot.
  • Keep the motor away from water, moisture, and corrosive materials.
  • Use only compatible Electronic Speed Controllers (ESCs) and power sources as specified.
  • Always disconnect the battery when not in use or during maintenance.
  • Operate RC models in open areas, away from people, animals, and obstacles.

3. Product Overview

The XeRun V10 G5 motor is engineered for peak performance and durability. Key features include:

  • Enhanced Power & Efficiency: Delivers a 3.9% boost in maximum output power and over 4% improvement in heavy-load efficiency compared to its predecessor, the V10 G4R 13.5T.
  • Lighter Chassis Weight: Redesigned to be 13g lighter, with mass distribution optimized closer to the vehicle's centerline for improved cornering balance.
  • Advanced Passive Cooling: Features an updated endbell design that exposes 15% more of the windings to airflow, alongside a patented rotor cooling system for excellent heat dissipation.
  • Superior Materials: Constructed with a high-performance premium stator core, 180°C high-temperature-rated reinforced rotor design, and top-tier bearings.
  • Precise Tuning: Offers an adjustable timing assembly (20–60 degrees) and adjustable sensor-to-rotor spacing (three gap settings) to customize power delivery.
  • Modular Design: Allows for quick and simple motor cleaning and maintenance.
Comparison of HOBBYWING XeRun V10 G5 13.5T and V10 G4R 13.5T motors, highlighting performance improvements.
Comparison of XeRun V10 G5 and V10 G4R motors, showing performance gains.
Exploded view of the XeRun V10 G5 motor showing its components, highlighting premium stator core, reinforced rotor, top-tier bearings, and modular design for easy maintenance.
Internal components and modular design for easy maintenance.

4. Specifications

The following table details the specifications for the XeRun V10 G5 13.5T motor. Specifications may vary slightly for other T-ratings.

Detailed specifications table for the HOBBYWING XeRun V10 G5 13.5T motor.
Specifications for XeRun V10 G5 13.5T Motor (PN: 30401762)
Category Parameter Value (13.5T)
Type Scale 1/10th
Brushed/Brushless BL (Brushless)
Sensored/Sensorless SD (Sensored)
Pole Count 2
Relevant Parameters KV Rating 4050KV
LiPo Cells 1-3S LiPo
No-load Current (A) 5.4A
Size & Weight O.D. (mm) 35.8
Length (mm) 51.5
Shaft Diameter (mm) 3.175
Weight (g) 138g
Bearings Front: D9*D4*T4, Rear: D8*D3*T4
Other Parameters Compatible ESC XeRun XR10 PRO G3 / G3X
Recommended Vehicles 1/10, 1/12 Stock Racing

5. Setup

5.1 Installation

  1. Mounting the Motor: Securely mount the motor to your vehicle's motor mount using appropriate screws. Ensure proper gear mesh between the motor pinion and spur gear.
  2. Wiring to ESC: Connect the three motor wires to the corresponding output wires of your compatible HOBBYWING ESC (e.g., XeRun XR10 PRO G3 / G3X). For sensored operation, connect the sensor cable from the motor to the sensor port on the ESC.
  3. Power Connection: Connect the ESC to your LiPo battery (1-3S recommended).

5.2 Adjustable Hall Sensing Distance

The rotor and sensor spacing can be adjusted to fine-tune power delivery. This allows racers to optimize the motor's response and feel.

  • Available settings: 0.1mm, 0.2mm, 0.3mm.
  • Warning: Ensure proper clearance between the Hall sensor and rotor ring during adjustment to prevent component damage. Refer to the diagram below for visual guidance.
Diagram showing adjustable Hall sensing distance settings (0.1mm, 0.2mm, 0.3mm) for the XeRun V10 G5 motor.
Adjustable Hall Sensing Distance settings.

5.3 Adjustable Hall Timing Accuracy

The timing assembly introduces new adjustments for further fine-tuning of the sensors. This allows for smoother and more efficient motor operation. The timing tolerance is based on results displayed by the HOBBYWING Tunalyzer.

For visual demonstration of the adjustable timing, please refer to the product video:

Product video demonstrating features including adjustable timing.

6. Operating the Motor

Once installed and configured, the motor operates in conjunction with your ESC. Ensure your ESC is programmed correctly for a sensored brushless motor. Always monitor motor temperature during initial runs to prevent overheating, especially when experimenting with timing and gearing.

  • Initial Run: Perform a short test run to ensure all components are functioning correctly and there are no unusual noises or vibrations.
  • Temperature Monitoring: Regularly check the motor temperature. Excessive heat can damage the motor and reduce its lifespan. Adjust gearing or ESC settings if the motor consistently runs too hot.
  • Gearing: Proper gearing is crucial for optimal performance and motor longevity. Consult your vehicle's manual and ESC recommendations for appropriate gear ratios.

7. Maintenance

Regular maintenance will ensure the longevity and consistent performance of your XeRun V10 G5 motor.

  • Cleaning: The modular design allows for quick and simple motor cleaning. Regularly remove dirt, dust, and debris from the motor, especially around the endbell and windings, to maintain optimal heat dissipation.
  • Bearing Inspection: Periodically inspect the front and rear bearings for smooth operation. Replace if they feel rough or show signs of wear.
  • Sensor Cable: Check the sensor cable for any damage or loose connections. A faulty sensor cable can lead to inconsistent performance.
  • Rotor Inspection: Ensure the rotor is free from damage and spins freely.
Diagrams illustrating the XeRun V10 G5 motor's excellent heat dissipation features, including a new endbell design exposing windings and a patented rotor cooling system.
Excellent heat dissipation through endbell design and patented rotor cooling.

8. Troubleshooting

If you encounter issues with your motor, consider the following common troubleshooting steps:

  • Motor Not Spinning:
    • Check all wiring connections between the motor, ESC, and battery.
    • Ensure the battery is charged and functioning correctly.
    • Verify ESC programming for sensored brushless motor operation.
    • Inspect the sensor cable for damage or improper connection.
  • Inconsistent Performance / Cogging:
    • Recheck sensor cable connection and ensure it's not damaged.
    • Verify Hall sensing distance and timing settings.
    • Ensure proper gear mesh and that no debris is obstructing the drivetrain.
    • Check for any loose motor screws or internal damage.
  • Overheating:
    • Reduce gearing (use a smaller pinion or larger spur gear).
    • Check for excessive drag in the drivetrain.
    • Ensure adequate airflow to the motor.
    • Verify ESC settings are not overly aggressive.
  • Reduced Power / Efficiency:
    • Check battery health and charge level.
    • Inspect motor for dirt or debris affecting performance.
    • Review Hall sensing distance and timing settings for optimal tuning.

9. User Tips

  • Fine-tuning: The adjustable Hall sensing distance and timing accuracy are powerful tools. Experiment with these settings to find the optimal power delivery and response for your specific vehicle and track conditions.
  • Performance Expectations: While the V10 G5 offers significant improvements, be aware that performance in specific racing classes (e.g., 'blinky class' where timing is fixed) might be subject to class rules and may not fully utilize all advanced tuning features.
  • Compatibility: Ensure your ESC is fully compatible with sensored brushless motors and specifically with the HOBBYWING XeRun XR10 PRO G3 / G3X for best results.

10. Frequently Asked Questions (FAQ)

Q: Is this motor suitable for all 1/10 scale RC cars?
A: The XeRun V10 G5 is primarily designed for 1/10 and 1/12 Stock Racing vehicles. While it may fit other 1/10 scale cars, its performance characteristics are optimized for racing applications.
Q: What ESCs are compatible with this motor?
A: For optimal performance, HOBBYWING XeRun XR10 PRO G3 / G3X ESCs are recommended. Ensure any ESC used is compatible with sensored brushless motors.
Q: How can I prevent my motor from overheating?
A: Proper gearing is key. Consider using a smaller pinion or larger spur gear. Also, ensure good airflow around the motor and keep it clean from debris. Adjusting ESC settings can also help manage heat.

11. Warranty and Support

For warranty information and technical support, please refer to the official HOBBYWING website or contact your local HOBBYWING distributor. Keep your proof of purchase for any warranty claims.

© 2023 HOBBYWING. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.