GALAX PRO 7R201

Contents

GALAX PRO Electric Jigsaw with Laser Guide

Model: 7R201

1. Introduction

Thank you for choosing the GALAX PRO Electric Jigsaw. This powerful 800W tool is designed for precise cutting in various materials, featuring a laser guide for accuracy, 6 variable speeds, and a 4-position cutting action. Please read this manual carefully before operation to ensure safe and efficient use of your jigsaw.

GALAX PRO Electric Jigsaw, front-side view
Figure 1: GALAX PRO Electric Jigsaw (Model 7R201)

2. Safety Instructions

Always follow basic safety precautions to reduce the risk of fire, electric shock, and personal injury.

  • Wear appropriate personal protective equipment (PPE) including safety glasses, hearing protection, and gloves.
  • Ensure the workpiece is securely clamped before cutting.
  • Keep hands and fingers away from the cutting area and the saw blade.
  • Disconnect the power plug from the power source before making any adjustments, changing accessories, or storing the tool.
  • Keep the work area clean and well-lit. Cluttered or dark areas invite accidents.
  • Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
  • Avoid unintentional starting. Ensure the switch is in the off-position before connecting to power, picking up or carrying the tool.
  • Maintain the tool. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’s operation.

3. Package Contents

Verify that all items are present upon unpacking:

  • 1 x GALAX PRO Electric Jigsaw (Model 7R201)
  • 1 x HCS TI44D Wood Blade
  • 1 x HSS T118A Metal Blade
  • 1 x Metal Ruler Guide
  • 1 x Allen Wrench
  • 1 x Vacuum Connector
  • 1 x User Manual (this document)

4. Specifications

Feature Specification
Model 7R201
Power 800 W
No-Load Speed 0-3000 rpm (revolutions per minute)
Speed Settings 6 Variable Speeds
Cutting Capacity (Wood) 80 mm
Cutting Capacity (Metal) 6 mm
Bevel Cutting Angle 0-45° (left and right)
Pendulum Action 4 Positions
Power Source AC (Electrified)
Motor Type Not specified (brushless status unknown)
Features Laser Guide, Tool-free Blade Change, Dust Extraction Port, Thickened Base

5. Setup

5.1 Blade Installation and Removal

The GALAX PRO Jigsaw features a tool-free blade change system for quick and easy blade replacement.

  1. Ensure the jigsaw is unplugged from the power source.
  2. Locate the blade clamp lever/mechanism at the front of the tool.
  3. Push or pull the lever to open the blade clamp.
  4. Insert the T-shank jigsaw blade into the clamp opening until it clicks into place. Ensure the teeth are facing forward.
  5. Release the lever to secure the blade. Gently pull on the blade to confirm it is firmly seated.
  6. To remove, open the clamp lever and pull the blade out.

5.2 Adjusting Bevel Angle

The base plate can be adjusted for bevel cuts up to 45 degrees in both directions.

  1. Unplug the jigsaw.
  2. Loosen the screws or lever that secure the base plate to the main body of the jigsaw (typically located underneath the base).
  3. Tilt the base plate to the desired angle (0-45°). Use the angle scale for reference.
  4. Tighten the screws or lever securely to lock the base plate in position.
Diagram illustrating 45 degree bevel cutting capability
Figure 2: 45° Bevel Cutting Adjustment

5.3 Connecting Dust Extraction

For a cleaner work environment and improved visibility of the cutting line, connect a vacuum cleaner to the dust extraction port.

  1. Locate the dust extraction port at the rear of the jigsaw.
  2. Attach the provided vacuum connector to the port.
  3. Connect a suitable vacuum hose to the vacuum connector.
Jigsaw with dust extraction port and hose connected
Figure 3: Dust Extraction Setup

5.4 Using the Laser Guide

The built-in laser guide assists in cutting straight and accurate lines.

  1. Locate the laser activation button (usually near the handle).
  2. Press the button to turn on the laser. A red line will project onto your workpiece, indicating the cutting path.
  3. Align the laser line with your desired cut line on the material.
Close-up of the laser guide and thickened base for stability
Figure 4: Laser Guide and Thickened Base
Jigsaw laser guide projecting a line onto a workpiece
Figure 5: Laser Guide in Action

6. Operating Instructions

6.1 Powering On/Off

  • To turn on the jigsaw, press the trigger switch.
  • To maintain continuous operation, press the lock-on button while the trigger is depressed.
  • To turn off, release the trigger switch. If the lock-on button is engaged, press the trigger again to release it.

6.2 Adjusting Variable Speed

The jigsaw features 6 variable speed settings, allowing you to match the speed to the material and application.

  1. Locate the speed control dial (typically on the side or top of the tool).
  2. Rotate the dial to select the desired speed from 1 (lowest) to 6 (highest).
  3. Lower speeds are suitable for harder materials or intricate cuts, while higher speeds are for softer materials and faster cutting.

6.3 Selecting Pendulum Action (4-Position Cutting Action)

The 4-position pendulum action allows for faster cutting and improved chip clearance, especially in wood. It also extends blade life.

  1. Locate the pendulum action selector lever (usually on the side of the tool).
  2. Select position '0' for no pendulum action (for fine cuts in metal or plastic).
  3. Select positions '1' to '3' for increasing levels of pendulum action (for faster cuts in wood).
Diagram showing the 6 variable speed settings and 4-position cutting action (pendulum)
Figure 6: Variable Speed Dial and 4-Position Cutting Action

6.4 Cutting Techniques

  • Straight Cuts: Use the metal ruler guide for precise straight cuts. Ensure the base plate is set to 0° bevel.
  • Curved Cuts: Use a fine-tooth blade and a lower speed setting. Apply steady, even pressure.
  • Bevel Cuts: Adjust the base plate to the desired angle (up to 45°).
  • Plunge Cuts: For internal cuts without a pilot hole, tilt the jigsaw forward so the front of the base plate rests on the workpiece. Start the saw and slowly lower the blade into the material.
Jigsaw cutting a circular line in wood
Figure 7: Example of Circular Cutting

6.5 Material Compatibility

  • Wood: Max 80mm thickness. Use HCS (High Carbon Steel) blades.
  • Metal: Max 6mm thickness. Use HSS (High Speed Steel) blades.
  • PVC/Plastic: Suitable for plastic pipes and tubes. Use appropriate blades and speed settings.
Jigsaw cutting wood, demonstrating 80mm cutting capacity
Figure 8: Cutting Wood (Max 80mm)
Jigsaw cutting PVC pipe
Figure 9: Cutting PVC
Jigsaw cutting metal, demonstrating 6mm cutting capacity
Figure 10: Cutting Metal (Max 6mm)

7. Maintenance

Regular maintenance ensures the longevity and optimal performance of your jigsaw.

  • Cleaning: After each use, unplug the tool and clean any dust or debris from the ventilation slots, blade area, and base plate. Use a soft brush or compressed air.
  • Blade Replacement: Replace dull or damaged blades promptly. Refer to Section 5.1 for blade installation/removal.
  • Cord Inspection: Regularly inspect the power cord for any signs of damage. If damaged, have it repaired by a qualified technician.
  • Lubrication: This tool is generally maintenance-free regarding lubrication. Do not attempt to lubricate internal components unless specified by the manufacturer.
  • Storage: Store the jigsaw in a dry, secure place out of reach of children.

8. Troubleshooting

Problem Possible Cause Solution
Jigsaw does not start No power supply; Faulty switch; Damaged cord Check power outlet and connections; Contact service for switch/cord replacement.
Blade not cutting efficiently Dull or incorrect blade for material; Incorrect speed setting; Excessive feed pressure Replace blade; Use correct blade type; Adjust speed; Reduce feed pressure.
Blade breaks frequently Wrong blade for material; Excessive pendulum action; Blade binding Use correct blade; Reduce pendulum action; Ensure workpiece is stable.
Laser guide not visible Laser is off; Dirty laser lens; Bright ambient light Turn on laser; Clean laser lens; Work in less bright conditions.
Excessive vibration Loose blade; Damaged blade; Worn components Ensure blade is securely clamped; Replace blade; Contact service.

9. User Tips

  • Quick Blade Changes: Users appreciate the very quick and convenient tool-free blade change mechanism. Utilize this feature to easily switch between blades for different materials or when a blade becomes dull.
  • Laser Guide Effectiveness: While the laser guide is a helpful feature for straight cuts, some users find its visibility can be limited in very bright conditions or that the support point is small. For critical cuts, always double-check your line with a pencil and ruler.
  • Power for the Price: This jigsaw offers good power for its price point, making it suitable for a variety of DIY and general maintenance tasks.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the documentation provided at the time of purchase or contact the seller directly. Keep your purchase receipt as proof of purchase.

© 2023 GALAX PRO. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.