EVERCROSSBOT Y10 Robotic Pool Cleaner User Manual

1. Introduction

Thank you for choosing the EVERCROSSBOT Y10 Robotic Pool Cleaner. This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your device. Please read it thoroughly before use and keep it for future reference.

The EVERCROSSBOT Y10 is a smart and efficient robotic pool cleaner designed for floor cleaning in swimming pools up to 120 square meters. It features a 180-micron high-precision filter, a 3-liter debris capacity, and a powerful 40W motor. With its wireless design, self-parking function, and durable IPX8 waterproof construction, it offers a convenient and reliable solution for maintaining a clean pool.

2. Important Safety Precautions

To ensure safe operation and prevent damage, please observe the following:

• Read this manual carefully and use the machine accordingly. We are not liable for any loss or injury caused by improper use.
• Use only accessories recommended or sold by the manufacturer.
• This model applies only to swimming pools with flat floors.
• Children are not allowed to ride or play with the machine.
• Use only authorized power adapters.
• Do not immediately open the machine clip when it is out of water.
• When charging, connect the charging adapter to an anti-leakage and corrosion-proof socket.
• Do not operate the machine when people or animals are in the pool.
• After use, always clean the filter and the lower shell of the machine.
• Shut down the machine during maintenance, cleaning, or non-use.
• Store the machine in a cool and ventilated place away from direct sunlight.
• When charging, place the machine in a cool place and do not cover anything to prevent overheating from damaging internal electrical parts.
• Only certified professionals shall disassemble the sealing parts of the machine.
• Do not remove the clips to open the machine while the swimming pool is open.
• The seal of the motor contains grease. If leakage is serious, it may cause water pollution.
• Due to battery capacity limitations, the machine is only applicable to water tanks up to 100 square meters; otherwise, the cleaning effect will be influenced.
• If the machine needs to be stored for a long time, the battery shall be charged once every three months to keep its life between 40% and 60%. Use only the original authorized power adapter. If the machine does not charge for a long time, the battery voltage will be lower than the over-discharge protection voltage, which may cause damage to the battery.
• Do not use or store the machine near a heat source.
• Do not pierce the machine shell with nails or other sharp objects. Do not hammer or throw the machine.
• Ensure the charging socket is dry before charging.

3. Packing List

Verify that all items are present in the package:

• Machine Body (x1)
• Adapter (x1)
• Instruction Manual (x1)
• User Operating Guide (x1)
• Brush (x1)
• Floating Bracelet (x1)
• Cleaning Gadget (x1)

4. Product Structure

Familiarize yourself with the main parts of your robotic pool cleaner:

• Floating Bracelet: Used to retrieve the robot from the pool.
• Water Sensor: Detects water presence for operation.
• Switch Button: Powers on/off and controls operation.
• Charging Port: For connecting the charging adapter.
• Upper Shell: Top cover of the robot.
• Clip: Secures the upper shell to the lower shell.
• Filter: Collects debris and particles.
• Lower Shell: Bottom part of the robot.
• Brush: Assists in cleaning the pool surface.
• Cleaning Gadget: Tool for cleaning the filter.

5. Setup

5.1. Charging the Battery

1. Ensure the charging pin is clean and dry. Wipe it with a tissue or cotton swab and wait a few minutes to dry completely before charging.
2. Open the protective cap of the charging port.
3. Connect the attached adapter to the charging port on the machine.
4. Plug the adapter into an anti-leakage and corrosion-proof socket.
5. The indicator light will flash green during charging. It will turn solid green when fully charged. Charging typically takes 5-6 hours.
6. After charging, cover the protective cap to prevent water ingress.

5.2. Installing Brushes

Install the brushes at the bottom of the machine before use to prevent dust leakage and ensure effective cleaning.

5.3. Installing Floating Bracelet

1. Adjust the length of the towing rope according to the depth of your swimming pool.
2. Tie the rope to the designated position on the robot, as shown in the figure.

6. Operation

6.1. Starting the Machine

1. Press the switch light to turn blue. The machine is now powered on.
2. Gently place the robot into the water.
3. Allow the machine to sink to the bottom smoothly. It will begin working after approximately 30 seconds.
4. If the machine is not placed in water for operation, it will automatically shut down after 10 minutes. To restart, long-press the switch again.

6.2. Water Outlet Function and Wheel Adjustment

The machine has two water outlets. During normal operation, one outlet opens while the other closes, and water flows out of the open outlet, propelling the machine forward. The operator can adjust the settings of the front and rear small wheels according to the actual pool situation for optimal cleaning.

Default Setting (A-B): Apply this setting for most pools.

Note:

• The operator can adjust the settings according to the actual situation of the pool.

Video: EVERCROSSBOT Y10 Robotic Pool Cleaner demonstration, showing easy setup, cleaning process, and self-parking feature.

7. Maintenance

7.1. Cleaning the Filter

Regular cleaning of the filter is crucial for optimal performance.

1. Open the 4 clips and lift the upper shell of the machine.
2. Carefully take off the filter.
3. Flush the filter and the bottom shell with water to remove debris.
4. Use the provided cleaning gadget to thoroughly clean the filter.
5. Reassemble the machine by placing the filter back and securing the upper shell.
6. Close the clips firmly.

8. Troubleshooting (FAQ)

Q1. What color is the indicator light when the machine is operating?

• The stable blue indicator light indicates that the machine starts normally.
• The blue indicator light keeps on during operation, indicating that the machine is running normally.
• The red indicator flashes quickly, indicating that the battery is insufficient. Please charge the machine.

Q2. When there is no response after turning on the machine, and how can I solve the problem?

1. Check whether the battery is completely discharged before use.
2. If the machine cannot be turned on after connecting the charger or fully charged:
• If the battery has not been used for a long time, it may need replacement due to damage from long storage.
• If the machine still cannot be switched on after battery replacement, please contact customer service for parts replacement.

Q3. After pressing to start the machine, the blue light is on. After putting it into the water, you wait for 30 seconds, but the machine is not started. How to handle it?

1. Stop the machine and check whether it is jammed with other objects.
2. Wipe the surface of the water sensor clean and restart the machine.
3. If the machine still does not start after several attempts, contact customer service for accessory replacement.

Q4. What color is the indicator light on the machine when the adapter is charging?

• During the charging process, the indicator light flashes green.
• When fully charged, the indicator light will be solid green.

Q5. How to deal with the slower running speed of the machine and less suction?

1. Check whether the water outlet is blocked by sundries or if the filter is too dirty.
2. If so, clean the water outlet and filter manually first, then use the machine for daily maintenance.
3. After using the machine every time, it is recommended to charge the machine.

Q6. If the charging pin is corroded by long-time electrolysis, how to deal with it?

1. After each use, wipe the charging pin clean and dry with a tissue or cotton swab. Wait a few minutes for it to dry before charging.
2. Contact customer service personnel to replace accessories in this case.

9. Specifications

10. User Tips

• Protect Pool Lining: Some users suggest adding shock-absorbing foam or rubber around the robot to prevent it from hitting pool walls too hard, which could potentially damage the pool lining over time.
• Battery Life & Charging: The 100-minute battery life is generally sufficient for cleaning small to medium-sized pools (e.g., 3m diameter, 16,000L, 8m x 4m). Be aware that the charging time is relatively long (5-6 hours).
• Effective Cleaning: The robot is highly effective at cleaning the pool bottom, including removing stubborn old marks and small debris like pebbles. It is designed for floor cleaning and does not clean the water surface.
• Ease of Use: The robot is noted for its ease of use, with simple button controls and quick deployment into the pool.

11. Warranty & Support

11.1. Warranty Information

• The warranty will be invalid if the product is altered, misused, or repaired by unauthorized personnel.
• Warranty applies only to manufacturing defects and does not include any damage caused by improper handling of the product by the owner.
• During the warranty period, any claim or repair must be accompanied by the order number or record of purchase.

11.2. List of Replacement Parts

Consumable parts are not covered under warranty. You can order the following accessories from the store:

• Adapter
• Floating Bracelet
• Filter
• Cleaning Gadget
• Brush

For further assistance or to view the complete user manual in PDF format, please refer to the official document available at: EVERCROSSBOT Y10 User Manual (PDF)

You can also contact support at: support@evercrossbot.eu