ILIFE V5s Ultra

Contents

ILIFE V5s Ultra Robot Vacuum and Mop Combo User Manual

Introduction

Welcome to the ILIFE V5s Ultra Robotic Vacuum Cleaner manual. Thank you for choosing the ILIFE V5s Ultra Robotic Vacuum Cleaner. This guide will help you understand and operate your robot for optimal performance. For further assistance, visit www.iliferobot.com.

Safety Information

Important Safety Instructions

  • This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
  • Remove hazards such as power cords, small items, or loose objects from the floor before cleaning.
  • Fold carpet tassels under the rug and lift hanging curtains or tablecloths off the floor.
  • For staircases or elevated areas, test whether the robot detects edges. Use barriers if necessary.
  • Use only manufacturer-recommended accessories and original rechargeable battery and charging dock.
  • Ensure the voltage matches the specifications on the charging dock.
  • This device is for indoor home use only. Do not use outdoors or in commercial environments.
  • Do not use water to rinse the device or wipe it with a wet cloth.
  • Do not operate the robot on wet or flooded surfaces.
  • Do not use near open flames or fragile items.
  • Keep hair, fingers, and loose clothing away from moving parts and openings.
  • Do not vacuum hard, sharp, flammable, or burning objects.
  • Do not use a damaged charging dock or power cord.
  • Keep the power cord away from heat sources and do not allow the robot to run over it.
  • If the power cord is damaged, have it replaced by a qualified technician.
  • Ensure the dustbin and filter are installed correctly before use.
  • Do not operate in a room where an infant is sleeping.
  • Stop using the device if it has been dropped, damaged, exposed to water, or used outdoors. Contact customer service.
  • Not suitable for high-pile carpets or certain dark-colored carpets.

Danger – Critical Safety Warnings

  • Disconnect the product from power if not used for a long period.
  • Always unplug the charging adapter before maintenance.
  • WARNING: Non-rechargeable batteries must not be recharged.
  • WARNING: For the purposes of recharging the battery, only use the detachable supply unit (model: K12V190060G) provided with this appliance.
  • This product is equipped with a rechargeable battery with a capacity of 2400mAh.
  • This appliance contains batteries that are only replaceable by skilled persons.
  • If any battery leakage is found, stop using the product immediately and contact the after-sales service center for assistance.
  • Do not power the device via external switches or circuits controlled by utility services.
  • If the power cord is damaged, it must be replaced by the manufacturer or authorized agent.
  • Maintain at least 20 cm distance between the antenna and your body during operation.
  • Frequency bands: Bluetooth 2402–2480 MHz; Wi-Fi 2412–2472 MHz.
  • Maximum RF transmission power: Bluetooth <10 dBm (EIRP), Wi-Fi <20 dBm (EIRP).
  • Before discarding the product, power it off and remove the battery.
  • Dispose of batteries according to local regulations.
  • Do not incinerate the product or battery even if damaged.
  • Use the product only as described in this manual. ILIFE is not responsible for loss or injury from misuse.

Network Interface

Bluetooth (Bluetooth LE) Interface: The device will enable Bluetooth by default before network distribution. Its primary function is for near-field device discovery and initial connection. When you are ready to connect the device to a network, your mobile phone and other smart devices can quickly find the device via Bluetooth and establish an initial communication link, preparing it for the subsequent Wi-Fi networking process.

Wi-Fi Interface: Before network distribution, the device's Wi-Fi interface is in an unconnected, configurable listening mode. It continuously listens for surrounding Wi-Fi signals and waits for commands sent by the user through the mobile application. Once it receives the correct connection command to a specified Wi-Fi network, the device supports the 2.4GHz Wi-Fi band, which is suitable for stable connections with other smart devices in your home.

P2P Interface: When the robot vacuum is powered on, it automatically broadcasts its location to the local network. After the mobile app obtains the device's address through the router, it establishes a direct communication channel with the robot vacuum. Identity verification is done using a key, enabling remote real-time control and point-to-point transmission of cleaning data.

What's in the Box

The ILIFE V5s Ultra package includes the following components:

ILIFE V5s Ultra Robot Vacuum and Mop Combo

ILIFE V5s Ultra Robot Vacuum and Mop Combo

  • Main Body
  • Charging Dock
  • Power Adapter
  • Water Tank
  • Mopping Support
  • Mop Cloth × 2
  • Remote Control
  • Cleaning Brush
  • High Performance Filter
  • User Manual
  • Side Brush × 2
  • AAA Battery × 2

Unboxing the ILIFE V5s Ultra Robot Vacuum and Mop Combo, showing all included accessories.

Product Overview

Robot Components (Top View)

ILIFE V5s Ultra top view with components labeled

Top view of the robot, highlighting the bumper, start/pause button, and middle cover.

  • Bumper: Protects the robot from collisions.
  • Start/Pause Button: Initiates or pauses cleaning cycles.
  • Middle Cover: Access point for dustbin and other internal components.

Robot Components (Underside View)

ILIFE V5s Ultra bottom view with components labeled

Underside view of the robot, showing cliff sensors, charging pins, side brushes, and wheels.

  • Cliff Sensors: Detects drops and prevents the robot from falling.
  • Charging Pins: Connects to the charging dock for power.
  • Side Brush: Sweeps debris into the suction path.
  • Battery Compartment: Houses the robot's battery.
  • Front Wheel: Provides navigation and maneuverability.
  • Suck Passage: Where debris is vacuumed into the dustbin.
  • Side Wheels: Main driving wheels for movement.

Water Tank Assembly

Water tank assembly diagram

Diagram of the water tank assembly, showing the rubber plug, water inlet, handle, and weep hole.

  • Rubber Plug: Seals the water inlet.
  • Water Inlet Plug: Point for filling water.
  • Handle: For easy removal and insertion of the tank.
  • Weep Hole: Allows water to flow to the mop cloth.

Dustbin Components

Dustbin components diagram

Diagram of the dustbin, showing the primary filter, high performance filter, and filter frame.

  • Primary Filter: Catches larger dust particles.
  • High Performance Filter: Traps fine dust and allergens.
  • Filter Frame: Holds the filters in place.

Charging Dock Components

Charging dock components diagram

Diagram of the charging dock, showing the signal light, charging pins, and power supply socket.

  • Signal Light: Indicates power status.
  • Charging Pins: Connects to the robot for charging.
  • Power Supply Socket: Connects to the power adapter.

Buttons and Indicator Lights Instruction

Robot StatusLight Status
ChargingAll lights pulse in a regular, rhythmic cycle
Charging finishedAll lights turn solid
In selected modeAll lights flash slowly
When robot in errorAll lights flash
Low batteryMiddle lights flash
In home modeMiddle lights flash slowly
In cleaning modeMiddle lights turn solid
In edge modeMiddle lights turn solid, lower lights flash
In spot modeMiddle lights turn solid, upper lights flash
Distribution modeAll lights flash
Distribution network successAll lights stay on solid for 1 second

Remote Control Guide

Before using the remote, insert two AAA/R03 batteries. Remove the batteries if not used for a long time.

Remote control with display showing time and schedule

Remote control with display showing current time and scheduled cleaning time.

ButtonFunction
PowerStart or pause cleaning
DirectionIn standby mode: Forward, Left, Right (Not functional during running)
MAX ModeSwitch Suction Level by Each Press: Standard → Max → Standard
ScheduleTo enter schedule mode. To confirm cleaning schedule.
ClockTo enter clock mode. To confirm time setting.
Spot ModeDeeply cleans a 1.5m × 1.5m area in a spiral pattern
Edge ModeCleans along walls and furniture edges
HomeSend the robot back to the charging dock manually

Technical Specifications

Product specifications diagram

Visual representation of key product specifications.

SpecificationDetails
ModelV5s Ultra
Dimensions300 × 300 × 81 mm
Battery TypeLi-ion
Charging TypeAuto Charging / Manual Charging
Charging Time< 350 minutes
Dustbin Capacity0.3 L
Water Tank Capacity0.3 L
Net Weight2.2 kg
Cleaning ModesAuto, Spot, Edge, Daily Schedule
Main Body Button TypeTouch Button
Weight<3 kg
Number of operating modes3-4
Filter TypeHEPA
LCDNo
Cleaning RoutePlanned Type
Bag Or BaglessBagless
Cord Length (m)WireLess
Handle MaterialOthers
Timing ReservationYes
Dust Storage TypeDust Box
InstallationRobot
Certificationce
Power (W)40w
FunctionWet and Dry
Voltage14.4 V
Remote ControlYes
OriginMainland China
Warranty2 years

Note: Specifications are subject to change without notice as we continuously improve our products.

Setup

Important Pre-Cleaning Notes

Frequent use helps the robot learn your home layout for more efficient path planning and reduced missed spots. Follow these guidelines before each use to protect your home and maximize the robot's cleaning efficiency:

  • A. Remove loose items from the floor: Clear cables, clothing, or small objects that could get tangled in the wheels or brushes.
  • B. Fold the rug's tassel trim underneath: Prevent tangling during cleaning. Avoid using on high-pile or thick rugs.
  • C. Block off dangerous zones: For areas like fireplaces, vents, or staircases, place physical barriers or set “No-Go Zones" in the app.
  • D. Avoid use on floor with excessive water: Avoid vacuuming large amounts of water as it will potentially damage the robot.
  • E. Obstacle height limit: The robot can climb over thresholds up to 12mm (0.47").
  • F. Cliff sensor limitations: Although the robot includes anti-drop sensors, performance may decrease on dark carpets or reflective surfaces, or in the situation the sensors get stained. Use physical barriers as needed.

Installing and Using the Charging Dock

Placement Guidelines:

  1. Place the charging dock on a hard, flat surface against a wall.
  2. Ensure there are no obstacles within 2 meters in front and 1 meter on both sides.
  3. Avoid placing it in areas with strong sunlight or reflective surfaces.
  4. Keep it away from places where pets sleep to avoid noise disturbance.
Charging dock placement guidelines

Illustration of proper charging dock placement with clearance distances.

Power Connection: Connect the adapter with the charging dock. Plug in the power cable. Once powered, the signal light of the dock will light up.

Turn On the Robot: Turn on the power switch around the power socket, then the display panel will flash. (If no command is received, the robot will turn to sleeping mode after 10 minutes.)

Note:

  • Please always keep the power switch turned on. If not, it is unable to make the robot work.
  • If the power switch is turned off, all scheduling will be lost.
  • Before charging the robot, please make sure the power switch is turned on, or else the robot cannot be charged.

Charging the Robot

Two Charging Methods:

  1. Plug the power adapter directly into an outlet and connect it to the robot.
  2. Press the Home button on the remote control to make the robot return to the charging dock for automatic charging.
Robot charging methods

Illustrations of direct charging and automatic charging via the dock.

Proper Placement: Align the robot with the charging pins on the charging dock. When connected properly, all lights will pulse in a regular, rhythmic cycle. This distinctive breathing light pattern is your indicator that the robot is charging.

Charging Completes: When all lights stay on solid, it indicates that the battery has been fully charged. The robot will automatically enter sleep mode if no operation is detected within two minutes.

Note: Recharging the robot after each use helps extend battery life.

Important Notes (Daily Use):

  • Make sure the charging pins on the robot and charging dock remain clean to avoid poor contact.
  • Store the robot on the charging dock with the charging dock powered on.
  • Before first use, charge the robot overnight. When charging is finished, the display panel will turn off.

When Not in Use:

For long-term storage, fully charge the robot, turn it off, and store it in a dry, ventilated place.

Schedule Mode

To offer a complete automatic cleaning experience, the robot receives preset cleaning schedules. Set local time and schedules with the remote control. The robot will start cleaning automatically at the preset time every day.

Note:

  1. If the robot is not connected to the network, scheduled programs set via the remote control will be lost after a power outage. However, once the robot can auto-join the network and synchronizes with internet time, scheduled programs set via that path will be saved.
  2. Before setting local time and cleaning schedules, make sure the robot is switched on. A green flashing light indicates the robot is activated from Sleep mode. To activate the robot, tap on the robot or remote control.

Set local time with remote control:

Setting local time with remote control

Steps to set the current time using the remote control.

Set a schedule:

Setting a cleaning schedule with remote control

Steps to program a cleaning schedule using the remote control.

Cancel a schedule: Adjust time to "00:00" and save; or turn off the power switch on the robot.

  • Please pay attention to the prompt to see if the robot is successfully scheduled.
  • Rescheduling is required after changing batteries in the remote control.

Installing and Using the Water Tank & Mop

Mounting bracket and mopping cloth: The mop bracket with mop should be on the robot when the water tank is used.

Fill the Water Tank: Open the rubber plug on the tank and fill with clean water. Tip: Use purified water to reduce limescale buildup. Reseal the plug tightly to prevent leakage.

Filling the water tank

Illustration of filling the water tank and installing it into the robot.

Installing the Water Tank: Open the robot lid and put the water tank into the body, the weep hole of the water tank should be aligned with the weep hole on the robot body.

Start Mopping: Close the robot lid, press CLEAN button to start the wet cleaning. There is no vacuum suction function during the wet cleaning.

Important Notes:

  1. Dustbin is for dry clean and water tank is for wet clean.
  2. It is suggested to perform dry cleaning before wet cleaning for a better result.
  3. Do not use the mop on carpets.
  4. The water in the water tank flows out automatically, so it is prohibited to let the water tank be still inside or outside of the robot when there is still water in the tank. This will cause water logging on the floor.
  5. Please take out the water tank when you charge the robot vacuum cleaner.
  6. After mopping, remove the mop and wash/dry it to avoid mildew or odors.

Using the ILIFE Clean App

To access all features, it's recommended to control the robot through the ILIFE Clean App. The app supports 2.4GHz or dual-band 2.4GHz/5GHz networks but does not support 5GHz-only networks.

Step-by-Step Setup:

  1. Download the App: Scan the QR code or search for “ILIFE Clean” in your app store.
  2. Register/Login: Open the app and sign up or log in with your credentials.
  3. Enable Pairing Mode: First start the robot vacuum cleaner, press and hold the CLEAN button for 6 seconds, release the button once the indicator light flashes, and the device will enter pairing mode, meaning it has entered the networking mode.
  4. Add Device: Tap "Add Device” or the “+” icon in the top right corner to begin connecting.
ILIFE Clean App setup steps

Screenshots illustrating the ILIFE Clean App download, login, and device pairing process.

Wi-Fi Pairing Modes:

Bluetooth Pairing Mode:

  1. Go to your phone's settings, turn on Bluetooth and enable Bluetooth permission for ILIFE Clean app.
  2. Return to the ILIFE Clean app — the device will appear automatically and tap "Add" to begin.
  3. Select your 2.4GHz Wi-Fi network and enter the password to go next.
  4. The device starts downloading.
  5. Device is added successfully and done.
ILIFE Clean App Bluetooth pairing steps

Screenshots detailing the Bluetooth pairing process within the ILIFE Clean App.

AP (Access Point) Pairing Mode:

  1. In the app, choose your specific robot model.
  2. Choose your 2.4GHz Wi-Fi network and enter the password.
  3. Go to your phone's Wi-Fi settings and connect to a network that starts with "SmartLife". Return to the app once connected.
  4. Wait for the app to complete the device connection process.
ILIFE Clean App AP pairing steps

Screenshots detailing the AP (Access Point) pairing process within the ILIFE Clean App.

Operating Modes

The ILIFE V5s Ultra offers multiple cleaning modes to suit various needs:

  • Auto Mode: The robot intelligently navigates and cleans the entire area.
  • Max Mode: Provides maximum suction power for deeper cleaning.
  • Edge Mode: Cleans along walls and furniture edges to ensure thorough coverage.
  • Spot Mode: Focuses on a specific area, cleaning in a spiral pattern for concentrated dirt.
  • Schedule Mode: Allows you to set a predetermined time for the robot to start cleaning automatically each day.
Four cleaning modes: Auto, Max, Edge, Spot

Visual representation of the robot operating in Auto, Max, Edge, and Spot cleaning modes.

Planned routes for efficient whole-home cleaning

The robot uses gyroscope navigation to create structured cleaning paths for efficient whole-home cleaning.

Maintenance

Always turn off the robot and unplug the power adapter before performing maintenance.

ComponentClean FrequencyReplace Frequency
Mop ClothAs neededEvery 3–6 months
DustbinWeeklyN/A
FilterN/AEvery 1–1.5 months
Side BrushWeeklyEvery 3–6 months (or if damaged)
Side WheelsMonthlyN/A
Cliff SensorsMonthlyN/A
Charging ContactsMonthlyN/A

Cleaning the Dustbin and Filter

  1. To open the robot's (top) cover, press the button marked PUSH.
  2. Remove the dustbin and check if there is any debris in the suction inlet, and then clean it.
  3. Open the dustbin lid, Remove the primary filter.
  4. Empty the dustbin.
  5. Remove the high performance filter and rinse the dustbin with water.
  6. Clean the primary filter and the high performance filter with the cleaning brush.
  7. Replace the high performance filter if necessary and reinsert the dustbin.
  8. Wipe the dustbin dry with a clean cloth and reinstall it into the robot.
Dustbin and filter cleaning steps

Visual guide for cleaning the dustbin and its filters.

Note:

  • A primary filter is replaceable and should be washed with water after having been in use for about 15-30 days, after which it should be dried in a cool and well-ventilated place and not to be squeezed.
  • High performance filter cannot be cleaned with water. To prolong the life of the filter it can be cleaned by shaking the filter.

Cleaning the Water Tank and Mop Cloth

Mop Cloth:

  1. Remove the mop bracket and peel off the cloth.
  2. Rinse with clean water and let it air-dry completely.
Mop cloth cleaning steps

Illustration of removing and cleaning the mop cloth.

Water Tank:

  1. Open the rubber plug and drain any leftover water.
  2. Wipe the tank clean and let it dry thoroughly.
Water tank cleaning steps

Illustration of draining and cleaning the water tank.

Cleaning the Side Brushes, Side Wheels and Front Wheel

Side Brushes:

  • Remove the screws and then remove the side brush, clean off the hair and other foreign objects tangled in it and wipe it off with a clean cleaning cloth.
  • When replacing the side brush, please distinguish the corresponding installation position of the "L" "R" side brush.
Side brush cleaning and replacement

Diagram showing how to remove and clean the side brushes.

Side Wheels: Check and remove any obstructions caught in the wheels.

Side wheel cleaning

Diagram showing the location of side wheels for cleaning.

Front Wheel: Clean any hair and foreign objects tangled in the front wheel, and wipe it with a clean cleaning cloth.

Front wheel cleaning

Diagram showing the location of the front wheel for cleaning.

Cleaning Sensors and Charging Pins

Cliff Sensors: Use a soft brush to gently clean the sensors on the underside of the robot.

Cliff sensor cleaning

Diagram showing the location of cliff sensors for cleaning.

Charging Pins: Wipe both the robot's and the charging dock's charging pins with a dry cloth to maintain charging efficiency.

Charging pin cleaning

Illustration of cleaning the charging pins on both the robot and the dock.

Battery Care and Activation

For Long-Term Storage:

  1. Charge the robot fully.
  2. Power it off.
  3. Store in a dry, ventilated place. Recharge every 3 months to avoid battery degradation.

Battery Activation (After Deep Discharge or Long Inactivity):

  1. Align the robot on the charging dock.
  2. Charge it for 3 minutes and then remove it. Repeat this process 3 times.
  3. Then charge continuously for 5-6 hours until it is fully charged when the indicator turns off.

Troubleshooting

The robot will remind you by beeping when it is malfunctioning.

Error Codes (Short Tones)

NO.TonePossible CauseWhat to do
01•Wheels or side brushes or fan problems.Check and clean wheels, side brushes, and fans.
02••OBS or bumper sensor or cliff sensor failure.Check the bumper and OBS, and clean cliff sensor.
03•••Robot gets stuck.Move the robot.
04••••Gyro failure.Detect and clean the gyro, and move the robot.

Error Appearance

Error appearanceLikely causeSolution
Circle around a small areaSide wheels are jammed
  • Remove hair and debris from side wheels.
  • While reinstalling, push the wheels in and out to make sure they can rotate freely.
  • Restart robot in another spot.
Keep moving backwardCliff sensor is dirty or brokenCheck cliff sensor lens. Clean or replace it if needed.
Bump into obstacles repeatedlyThe bumper is stuck
  • Tap the bumper 10-20 times to remove debris lodged in it.
  • Loosen the screw of the bumper.
Working time shortenedBattery capacity dropped or robot is not fully chargedReplace battery or recharge robot.
CLEAN button light is off while chargingHair or small debris stuck in charging pins or robot not properly connected to charging pins.Clean charging pins or check if robot is connected to charging pins.
Pick up less dirt and debrisFilter is dirty or wetClean or replace filter.
Spit out litterDustbin is fullEmpty the dustbin.
Robot doesn't start at scheduled timeSchedule not saved, canceled, power switch off, battery low, or debris jammed.
  • Reset schedule.
  • Turn on power switch.
  • Keep robot on charging dock and fully charged.
  • Turn off power switch, empty dustbin.
  • Clean side brushes and suck passage.

Note: If above solutions don't work, re-set the robot by re-turning on the power switch. If restarting still doesn't solve the problem, contact the after-sales center for repair.

Warranty and Support

Customer Service

For customer service and warranty inquiries, please contact ILIFE Customer Service at warranty_repair_EU@iliferobot.com (for Europe) or visit the official website www.iliferobot.com for more detailed information and support.

User Tips

  • Regularly check the app for cleaning maps and history to monitor performance and ensure thorough cleaning. The robot provides detailed logs of time spent and area covered.
  • The robot will not resume cleaning after recharging during a scheduled cycle; it will wait for the next scheduled time. If immediate cleaning is needed, manually send a command via remote control or app.
  • It's safe to leave the robot on the charging dock when not in use, as it features trickle charging to prevent overcharge and maintain battery health.

Frequently Asked Questions (FAQ)

Q: The robot has returned to its charging dock for recharge during the scheduled time. Will it resume to work after recharge or until the next scheduled cycle?
A: The robot responds to scheduled cleaning once a day only. After recharge, it will start working automatically when the next schedule comes. If you need the robot to clean now, send a command with the remote control.
Q: Will the robot keep cleaning until the scheduled cycle finishes?
A: Yes, the vacuum will keep cleaning unless you press PAUSE or its battery level is low and it returns to the charging base.
Q: Can the robot clean water spots in the kitchen or bathroom?
A: The robot must not be used on wet floors. Vacuuming liquids will damage the robot.
Q: Can I leave the robot on the charging dock if I'm not using it for some time?
A: Yes. After the robot is fully charged, it will enter trickle charging to compensate self-discharge in the battery and avoid overcharge. Do not allow children to charge the robot. Turn off the power switch if it will not be used for a long time.
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.