ANDELI RL-600LB

Contents

ANDELI Auto Darkening Welding Helmet User Manual

Model: RL-600LB

Brand: ANDELI

Introduction

Thank you for choosing the ANDELI Auto Darkening Welding Helmet, Model RL-600LB. This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your welding helmet. Please read this manual thoroughly before use to ensure proper functionality and safety.

Video: ANDELI Auto Darkening Welding Helmet Product Demonstration.

1. Safety Information

WARNING: Please read and understand all safety warnings and instructions before using this welding helmet. Failure to do so may result in serious personal injury or equipment damage.

1.1 General Safety Precautions

  • Always inspect the helmet and filter lens for proper fit and condition before welding.
  • Ensure the clear lens is clean and securely attached.
  • Always wear safety glasses or goggles under the welding helmet.
  • Wear appropriate protective clothing to shield skin from radiation, burns, and spatter.
  • Ensure no optical radiation from other welders' arcs enters from behind the helmet.
  • Auto-darkening filters protect against harmful UV/IR rays in both dark and light states.
Welder using the ANDELI helmet with LED sidelights

Image: Welder using the helmet, illustrating the LED sidelights illuminating the workspace.

1.2 Fumes and Gases

  • Welding produces fumes and gases hazardous to health. Avoid breathing these fumes.
  • Keep your head out of the fume plume.
  • Use sufficient ventilation or exhaust at the arc to keep fumes and gases away from your breathing zone.
  • When welding with electrodes which require special ventilation (e.g., stainless steel, hard facing, lead/cadmium plated steel), keep exposure as low as possible and within applicable OSHA PEL and ACGIH TLV limits.
  • A respirator may be required in confined spaces or outdoors under certain circumstances.

1.3 Arc Rays

  • Arc rays can injure eyes and burn skin.
  • The electrode and work (or ground) circuits are electrically “hot” when the welder is on. Do not touch these "hot" parts with bare skin or wet clothing.
  • Wear dry, hole-free gloves to insulate hands.
  • Insulate yourself from work and ground using dry insulation.
  • Protect nearby personnel with non-flammable screening and warn them not to watch the arc.

1.4 Electric Shock

  • Electric shock can be fatal.
  • Ensure the work cable makes a good electrical connection to the metal being welded, as close as possible to the welding area.
  • Ground the work or metal to be welded to a good electrical (earth) ground.
  • Maintain electrode holder, work clamp, and welding cable in good, safe operating condition. Replace damaged insulation.
  • Never dip the electrode in water for cooling.

1.5 Welding and Cutting Sparks

  • Sparks and hot materials can cause fire or explosion.
  • Remove fire hazards from the welding area or cover them.
  • Have a fire extinguisher readily available.
  • Do not weld near hydraulic lines.
  • Do not heat, cut, or weld tanks, drums, or containers that have held hazardous substances without proper cleaning and ventilation.
  • Vent hollow castings or containers before heating, cutting, or welding.

1.6 Electromagnetic Fields (EMF)

  • Electric current creates EMF fields.
  • EMF fields may interfere with pacemakers. Consult a physician before welding if you have a pacemaker.
  • Minimize exposure to EMF fields by routing electrode and work cables together, avoiding coiling the lead around your body, and connecting the work cable as close as possible to the workpiece.

2. Specifications

The ANDELI Auto Darkening Welding Helmet (Model RL-600LB) is designed with advanced features for optimal performance and safety. Below are the detailed specifications:

Specifications table and package contents for ANDELI welding helmet

Image: Detailed specifications and package contents.

FeatureRL-600LARL-600LB
Optical Class1/1/1/11/1/1/2
LCD Viewing Area115 x 82 mm (4.53" x 3.23")115 x 82 mm (4.53" x 3.23")
Cartridge Size131 x 135 mm (5.31" x 5.15" x 0.39")131 x 135 mm (5.31" x 5.15" × 0.39")
UV/IR ProtectionDIN 16DIN 16
Arc Sensors54
Variable Welding ShadesWELD Mode: Dark State: DIN 9-13, Light State: DIN 3; GRIND Mode: Light State: DIN 3; LOCK Mode: Dark State: DIN 5-13; CUT Mode: Dark State: DIN 5-9, Light State: DIN 3WELD Mode: Dark State: DIN 9-13, Light State: DIN 3; GRIND Mode: Light State: DIN 3; LOCK Mode: Dark State: DIN 5-13; CUT Mode: Dark State: DIN 5-9, Light State: DIN 3
Shade ControlDigital AdjustDigital Adjust
Sensitivity ControlDigital AdjustDigital Adjust
Power SupplySolar Cells + Polymer BatterySolar Cells + Polymer Battery
Battery Capacity500mAh500mAh
Charging TypeType-CType-C
Low Battery IndicatorYesYes
Light to Dark Switching Time0.07 ms0.08 ms
Dark to Light Switching Time0.1 - 2.0 s0.1 - 1.0 s
TIG RatingDC 5A / AC 5 ADC 5A / AC 5 A
Operating Temperature23°F to 131°F (-5°C to 55°C)23°F to 131°F (-5°C to 55°C)
Storage Temperature-4°F to 158°F (-20°C to 70°C)-4°F to 158°F (-20°C to 70°C)
Total Weight590 g560 g

The RL-600LB model features 4 arc sensors and a faster light-to-dark switching time of 0.08ms compared to the RL-600LA model's 0.07ms. Both models offer digital adjustment for shade and sensitivity, and are powered by solar cells and a polymer battery with Type-C charging.

3. Operating Instructions

3.1 Helmet Controls

Familiarize yourself with the control panel and external buttons for optimal use.

Overview of ANDELI welding helmet features including controls, view, and headgear

Image: Overview of helmet features and controls.

Internal Control Panel (RL-600LB)

Detailed view of the RL-600LB internal control panel with mode, test, shade, sensitivity, and delay buttons

Image: Internal control panel for RL-600LB model.

  1. Mode Key: Short press to switch between scene modes (Grind, Cut, Weld, Lock). Long press to Power On/Off.
  2. Test Button: Press to check if the auto-darkening function is working correctly.
  3. Shade Number / Intelligent Mode Button: Short press to adjust shade numbers (5-9/9-13). Long press for automatic adjustment.
  4. Delay / Intelligent Mode Button: Short press to adjust delay. Long press for automatic adjustment.
  5. Sensitivity Button: Short press to adjust sensitivity (5 levels). Long press for automatic adjustment.
  6. +/- Buttons: Used to adjust parameters (shade, sensitivity, delay).
  7. Memory Button: Short press to recall stored parameters. Long press to save current settings (shade, delay, sensitivity) into memory (9 storage slots).

External Button Control

External control knob for quick adjustments of shade, sensitivity, delay, and grind mode

Image: External control knob for quick adjustments.

  • Quick-Access Button: Instantly switches between Sensitivity and Delay adjustment modes.
  • Multi-Function Knob: Quickly adjusts Shade Number, Sensitivity, and Delay values.
  • Grind Mode Button: Long press for 1.5 seconds to activate grind mode immediately.

3.2 LED Instructions

The helmet is equipped with intelligent LED lights for illuminating your workspace.

LED light controls on the side of the welding helmet

Image: LED light controls.

  1. ON/OFF: Long press and hold for three seconds to turn on the light. Press again to switch between two adjustable brightness levels.
  2. Left LED: The green light indicates the spotlight is in operation.
  3. Infrared Sensor Switch: When the spotlight is in operation, press this switch to activate the infrared sensing mode, indicated by a flashing left indicator light.
  4. Infrared Sensor Probe: Hand motion can control the switch (on/off/high/low) without touching the helmet.

4. Adjusting Headgear

Proper headgear adjustment is crucial for comfort and safety.

Diagram showing various adjustment points on the welding helmet headgear

Image: Headgear adjustment points.

  1. Head Size Adjustment: Adjust headgear tightness by turning the Ratchet Knob (located at the back of the helmet) left or right for the desired head size.
  2. Crown Adjustment: Adjust the comfort by placing the strap under the guide and snapping the pins into the holes to lock securely.
  3. Tilt Adjustment: Located on the right side of the helmet. Loosen the right headgear tension knob, push the top end of the adjustment lever outward until the lever's Stop Tab clears the notches. Rotate the lever forward or back to the desired tilt position. The Stop will automatically engage when released.
  4. Fore/Aft Adjustment: Adjusts the distance between your face and the lens. Slide and hold the spring-loaded caps upward while moving the headgear into one of four slotted locations. Release the cap once the desired distance is achieved.

Note: Ensure both sides are equally positioned for proper orientation.

5. Battery Charging & Maintenance

The helmet is powered by a polymer battery with solar assist and Type-C charging.

Diagram showing Type-C charging port and solar panel on the welding helmet

Image: Type-C charging and solar panel.

  • The device is equipped with a polymer battery and supports charging via the Type-C port (rated input: DC 5V/1A).
  • A 50cm Type-C cable is included.
  • Recharge promptly when the battery level is low. The battery level is displayed in the top-right corner of the screen.
  • Battery Life:
    • Single battery: 2 hours of continuous operation.
    • Dual batteries: 4 hours of continuous operation.
    • An additional 1000mAh battery is dedicated to powering the 2 LED lights, ensuring extended welding sessions.
  • Charging time: Approximately 2.5-3 hours for a full charge.
  • Operation time: 2400+ hours without LED light, or up to 1200 hours with LED light on.

6. Cartridge and Lens Replacement

Regular inspection and replacement of lenses are essential for clear vision and protection.

6.1 Replacing the Outer Cover Lens

Diagram showing how to remove and install the outer cover lens

Image: Outer cover lens replacement diagram.

  1. Removal: Press down on one side of the buckle with your hand to release and remove the shell.
  2. Installation: To install a new shell, first align and clip it into the middle groove. Then, press firmly on both sides until it locks into place.

6.2 Replacing the Inner Cover Lens

Important: Never use the auto-darkening lens without the inside and outside lens covers properly installed. Welding spatter will damage the auto-darkening lens and void the warranty.

  1. Remove the lens cover holder and take out the lens assembly.
  2. To remove the inner lens cover, gently pry it upward using the thumbnail openings located on both sides.
  3. Slide the cover out from either side of the frame.
  4. Insert the new lens cover and reassemble the unit by reversing the above steps.

7. Troubleshooting

Refer to the table below for common issues and their solutions.

Fault DescriptionPossible CauseSolution
Irregular darkening or uneven dimmingImproperly adjusted headband causing uneven distance between eyes and filter lens.Readjust the headband to ensure equal distance to the filter on both sides.
Filter does not darken or flickers during useDirty or damaged outer protective lens.
Blocked or dirty arc sensors.
Welding current below activation threshold.
Low battery or poor contact.
Device not switched to appropriate operating mode.
Clean outer lens with a soft cloth; replace if damaged.
Gently clean sensor surfaces.
Increase sensitivity setting or welding current.
Check battery level, condition, and contacts; recharge or clean as needed.
Ensure device is powered on and set to correct welding mode via control panel.
Slow response when darkeningOperation in low-temperature conditions.Do not use below -10°C; allow helmet to warm to operating temperature.
Poor visibility through lensDirty outer/inner cover lenses or filter.
Insufficient ambient light in work area.
Incorrect shade number setting.
Replace soiled or scratched lenses.
Ensure adequate workspace lighting.
Adjust shade number to suitable level for the process.
Helmet slips during useLoose or improperly fitted headband.Adjust headband size and tension for secure and comfortable fit.

WARNING: If these troubleshooting steps do not resolve the issue, discontinue use immediately and contact ANDELI support for assistance. Do not use a malfunctioning auto-darkening helmet.

8. Replacement Parts

Below is an exploded view and a list of replacement parts for the headgear and helmet components.

8.1 Headgear Exploded View

Exploded view diagram of the welding helmet headgear components

Image: Exploded view of the headgear components.

  1. Sweat Band
  2. Plastic Nut
  3. Fix Set
  4. Adjusting Rack
  5. Angle Adjusting Shim
  6. Position Sleeve
  7. Locking Bolt
  8. Head Band
  9. Tightness Knob

8.2 Helmet Parts List

Diagram of welding helmet with numbered parts and corresponding list

Image: Welding helmet with numbered parts.

Part No.DescriptionQuantity
ADL-RL-010001Welding Helmet Shell1
ADL-RL-010002Outer Cover Lens1
ADL-RL-010003Lens Assembly1
ADL-RL-010004Inner Cover Lens1
ADL-RL-010005Side Cover Lens1
ADL-RL-010006External Control Button1
ADL-RL-010007Headgear1
ADL-RL-010008Helmet Bag1
ADL-RL-010009User Manual1
ADL-RL-0100010Type-C Charging Cable1
ADL-RL-0100011LED module2

9. User Tips

  • For optimal visibility, especially in low-light conditions, utilize the helmet's intelligent LED lights. Remember the motion sensor mode allows for hands-free brightness adjustment.
  • To maximize battery life, ensure the helmet is regularly exposed to sunlight for solar charging and use the Type-C charging cable when the low battery indicator appears.
  • Take advantage of the fully digital filter's internal panel for precise adjustments of shade, sensitivity, and delay to match your specific welding task and environment.
  • Regularly check and clean all lenses (outer, inner, and side) to maintain clear vision and ensure the auto-darkening function works effectively.
  • Properly adjust the headgear using all available adjustments (head size, crown, tilt, fore/aft) to achieve a comfortable and secure fit, which helps prevent fatigue and ensures consistent eye protection.

10. Warranty and Support

For warranty information, technical support, or to purchase replacement parts, please contact ANDELI customer service.

  • After-Sales Center:
    • USA: LIPOINCD-100, 12 Hughes Irvine, CA 92618
    • Hong Kong: Workshop60, 3/F, Block A, East Sun, Industrial Centre, No.16 Shing Yip Street, Kwun Tong, Hong Kong
    • Telephone: +19496179002 (USA); +85284807265 (HK)
    • Email: support@andeligroup.com
    • Website: www.andelitools.com

Please have your product model number (RL-600LB) and purchase details ready when contacting support.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.