1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Shengmilo G10 / NOKEE-U Intelligent LCD Display. Please read this manual thoroughly before using the display to ensure proper function and safety.
The NOKEE-U Intelligent LCD Display is designed for E-bikes and offers a variety of functions to enhance your riding experience.
Figure 1: Shengmilo G10 / NOKEE-U Intelligent LCD Display and Control Unit.
For a downloadable version of this manual, please refer to the official PDF document: User Manual (PDF).
2. Product Overview
2.1. Appearance and Size
The display unit has a width of approximately 62.0 mm and a height of 99.6 mm. The thickness of the display panel is about 7.2 mm. The control unit, which includes the buttons, is designed to fit handlebars with a diameter of 22.2 mm. The control unit measures approximately 49.4 mm in width and 36.3 mm in depth, with a height of 45.4 mm.
2.2. Function Summary
The NOKEE-U display provides a wide range of functions, including:
- Battery indication (5 bars, each representing approximately 20% capacity).
- Speed indication (running speed, max speed, average speed).
- Odometer and trip distance (single mileage and total mileage).
- Push-assistance level indication.
- Backlight On/Off.
- Trip time indication.
- Error code indication.
- Multiple setting parameters: wheel diameter, speed limit, battery power, assist gear selection, assist parameter, power-on password, controller current limit.
- Option to recover default settings.
2.3. Button Definition
The display features three buttons, primarily made of PC material with soft silicone for the button part. The entire unit is black. The buttons are referred to as:
- [MODE]: The power button, also used for mode selection and confirmation.
- [UP]: The 'plus' button, used for increasing values or navigating up.
- [DOWN]: The 'minus' button, used for decreasing values or navigating down.
The control unit is typically mounted on the handlebar, allowing easy access to these buttons.
2.4. Functional Area Distribution
The LCD display screen is organized into several functional areas:
- Top Bar: Displays 'ENERGY BAR' (battery level) and '188%' (full charge indication).
- Upper Middle: Shows 'SPEED', 'AVGMAX', and 'Error' indicators. The main numerical display shows speed (e.g., '88') with units 'MPH' or 'Km/h'.
- Lower Middle: Features 'Auto Manual' indicator, 'PAS' level (e.g., '8'), and a lighting indicator (a small light bulb icon).
- Bottom Bar: Contains 'TRIP', 'ABODO', 'REMAIN' (mileage/range indicators), and a numerical display (e.g., '8888.8') with 'MileKm' unit.
3. Setup
3.1. Installation
The display unit and control unit are designed for handlebar mounting. Ensure the mounting brackets are securely fastened to your e-bike's handlebar. Connect the display cable to the main e-bike wiring harness. The connector is typically a green, multi-pin circular connector, as shown in the product image.
Compatibility Note: This display is programmed with a proprietary factory protocol exclusive to Shengmilo. It is not a universal/DIY part. If you intend to use this on another brand of e-bike, consult with Shengmilo support first to avoid system errors or hardware damage.
4. Operation
4.1. Switching the E-bike System On/Off
- To Turn On: Briefly press the [MODE] button.
- To Turn Off: Hold the [MODE] button for 2 seconds.
- Automatic Shutdown: If the e-bike is parked for more than 10 minutes, the system will automatically switch off.
4.2. Display Interface Cycle
After powering on, the display defaults to showing Speed and Total Distance. You can cycle through various riding data by pressing the [MODE] button and [UP] button simultaneously. The sequence typically includes:
- Running Speed (Km/h)
- Average Speed (Km/h)
- Max Speed (Km/h)
To view mileage information, briefly press the [MODE] button. The display sequence for mileage is: TRIP A (single mileage A) → TRIP B (single mileage B) → ODO (cumulative mileage).
4.3. Switching Push-assistance Mode On/Off
To activate the push-assistance function, hold the [DOWN] button. The e-bike's drive will activate at a uniform speed of 6 Km/h, and "WALK" will appear on the screen. Release the [DOWN] button to switch off the push-assistance function.
Safety Warning: Push-assistance should only be used when pushing the e-bike. Do not use it if the wheels are not in contact with the ground to avoid injury.
4.4. Turning Headlights On/Off
To turn on the headlights, press and hold the [UP] button for 2 seconds. A light bulb icon will appear on the display. To turn off the headlights, press and hold the [UP] button again for 2 seconds.
4.5. Battery Indicator
The display shows battery capacity using 5 long bars. Each bar represents approximately 20% of the battery's capacity. When the battery is low, the battery icon will blink at 1 Hz, indicating that charging is required. If the display shows a specific low battery icon (e.g., a single blinking bar), it means the battery is under voltage and needs immediate charging.
5. Settings
All settings operations should be performed while the E-bike is parked.
5.1. General Settings
To access the general settings menu, hold both the [UP] button and the [DOWN] button for 2 seconds.
5.1.1. Trip Distance Clearance
TRIP A and TRIP B represent trip distance settings. To clear a single trip distance, press the [MODE] button or the [DOWN] button until the single trip distance resets to zero.
5.1.2. Unit km/mi Conversion (ST1)
ST1 represents unit settings. "MPH" is for miles, and "KM/h" is for kilometers. The default value is "KM/h".
- To convert units: Press the [UP] or [DOWN] button to select the desired unit, then press [MODE] to confirm.
- To save changes and access trip distance clearance settings: Press [MODE].
- To exit General Settings: Hold the [MODE] button for 2 seconds.
5.2. Personalized Parameter Settings
To access the Personalized Parameter Settings menu, hold both the [UP] and [DOWN] buttons for 2 seconds, then repeat this action (hold both [UP] and [DOWN] for another 2 seconds).
To navigate through settings items: Press [UP] or [DOWN] to select the desired item, then press [MODE] to confirm.
The personalized settings include: Battery Power Bar, Power Assistant Level, Over-current Cut, Power Assistant Sensor, Speed Sensor, Throttle Function, System, and Power-on Password settings.
5.2.1. Wheel Diameter Settings
Selectable wheel diameter values include 16, 18, 20, 22, 24, 26, 700C, and 28 inches. The default value is 26 inches.
- To change: Press [UP] or [DOWN] to adjust.
- To save and proceed to speed-limit settings: Press [MODE].
5.2.2. Speed-limit Settings
If the current speed exceeds the set limit, the e-bike system will automatically switch off. The speed limit range is 12 km/h to 40 km/h. The default value is 25 km/h.
- To change: Press [UP] or [DOWN] to adjust.
- To save and exit General Parameter Settings: Hold the [MODE] button for 2 seconds.
5.2.3. Battery Power Bar Settings (VOL)
VOL represents voltage settings. Each of the 5 battery bars corresponds to a voltage value. These 5 values must be entered one by one (e.g., VOL 1 is the first bar voltage value). The default value is 48V.
- To set: Press [UP] or [DOWN] to increase/decrease the number.
- To save and proceed to the next bar setting: Press [MODE].
- After setting all 5 bars and confirming: Hold [MODE] to return to the previous menu.
5.2.4. Assistance Level Settings (Optional)
There are 8 assistance level modes: 0-3, 1-3, 0-5, 1-5, 0-7, 1-7, 0-9, and 1-9. The default value is 0-5.
- To change: Press [UP] or [DOWN] to select the desired mode.
- To confirm and automatically access PAS ratio settings: Press [MODE].
5.2.5. PAS Ratio Settings
This setting modifies the PAS ratio. For example, for level 1, the range is "30-50 percent", with a default of 40 percent.
- To change: Press [UP] or [DOWN] to select the desired value.
- To confirm and move to the next PAS ratio setting: Press [MODE].
- After inputting all PAS ratios and confirming: Hold [MODE] for 2 seconds to return to the previous menu.
5.2.6. Controller Over-current Cut Settings (CUR) (Optional)
CUR values can be set from 7.0A to 18.0A. The default value is 15A.
- To change: Press [UP] or [DOWN] to adjust the current value.
- To save and return to the previous menu: Hold the [MODE] button.
5.2.7. Power Assistant Sensor Settings (Optional)
PAS settings include the direction of the sensor and its sensitivity.
Direction of PAS Settings
"run-F" means forward direction, "run-b" means backward direction. The default is "run-F".
- To change: Press [UP] or [DOWN] to select 'F' or 'b'.
- To save and access PAS sensitivity settings: Press [MODE].
Sensitivity of PAS Settings (SCN)
SCN values range from "2" (strongest) to "9" (weakest). The default value is "2".
- To change: Press [UP] or [DOWN] to select the sensitivity value.
- To save and access magnet disk settings mode: Press [MODE].
Magnet Quantity Settings (n)
This setting refers to the number of magnets on the PAS disk. The default value is 064. A larger value results in a more noticeable pedal assist feeling.
- To change: Press [UP] or [DOWN] to select the quantity according to your PAS disk.
- To save and return to the previous menu: Hold the [MODE] button.
5.2.8. Speed Sensor (SPS) (Optional)
SPS represents speed sensor settings. The default value is 1. This setting adjusts the quantity of magnet heads on the wheel spoke (range 1 to 9).
- To change: Press [UP] or [DOWN] to select the desired quantity.
- To save and return to the previous menu: Hold the [MODE] button.
5.2.9. Throttle Definition (Hnd) (Optional)
Hnd refers to throttle function settings, with two sections: HL and HF.
- HL: Represents "throttle" setting, i.e., push-assistance by turning the throttle.
- HL-n: Throttle push-assistance function is disabled.
- HL-y: Throttle push-assistance function is enabled.
The default value is HL-n (throttle disabled). If HL-y is selected, it will return to the previous menu.
5.2.10. Throttle -PAS Enable/Disable (HF)
HF represents the "throttle-PAS" setting.
- HF-y: Throttle speed is limited by the current assist level. The maximum speed can only be the highest speed powered by the current pedal assist level when twisting the throttle.
- HF-n: Throttle speed is not limited by the current pedal assist level. You can override the pedal assist level and reach the rated maximum speed when twisting the throttle.
The default value is "n".
5.2.11. Delay Time Settings of Battery Power (DL)
DL represents the delay time of battery power settings. The default value is 3 seconds. Selectable values are 3s, 6s, and 12s.
- To change: Press [UP] or [DOWN] to select the desired delay time.
- To save and access the max speed limit: Press [MODE].
5.2.12. Button Push-assistance Enable/Disable (PUS)
PUS represents button push-assistance settings. 'Y' means enabled, 'N' means disabled. The default value is 'Y'.
- To change: Press [UP] or [DOWN] to choose 'Y' or 'N'.
- To save and access PAS speed settings: Press [MODE].
5.2.13. Push-assistance Speed Settings
This setting adjusts the PAS speed from 20% to 35%. The default value is 25%.
- To change: Press [UP] or [DOWN] to adjust.
- To save and access slowly start up settings: Press [MODE].
5.2.14. Slowly Start-Up Settings (SSP)
SSP represents a slow start-up. The range is "1-4", where "4" is the slowest. The default value is "1".
- To change: Press [UP] or [DOWN] to select the desired value.
- To return to the previous menu: Hold the [MODE] button for 2 seconds.
5.2.15. Power-On Password Settings (P3)
"P3" on the screen indicates power-on password settings. The default password is 2962.
- To access: Press [UP] or [DOWN] to modify the value.
- To confirm digits one by one: Press [MODE].
- After completing the 4-digit password: Press [MODE] to access the power-on password enable settings interface. Otherwise, it will remain in the password input state.
6. Troubleshooting
6.1. Error Code Indication
The e-bike system components are continuously monitored. If an error is detected, a specific error code will be displayed in the text indication area on the screen. If an error code appears, the display needs to be repaired, as the bike may not be ridable.
Refer to the table below for definitions of common error codes:
| Error Code | Definition |
|---|---|
| 21 | Current Abnormality |
| 22 | Throttle Abnormality |
| 23 | Motor Abnormality |
| 24 | Motor Hall Signal Abnormality |
| 25 | Brake Abnormality |
| 30 | Communication Abnormality |
| 31 | Power Button Abnormality |
| 34 | 6km function button Abnormality |
7. Specifications
- Model: NOKEE-U
- Type: Intelligent LCD Display for E-bike
- Indicator Panel: LCD
- Dimensions (Display Unit): Approx. 62.0 mm (W) x 99.6 mm (H) x 7.2 mm (D)
- Dimensions (Control Unit): Approx. 49.4 mm (W) x 36.3 mm (D) x 45.4 mm (H)
- Handlebar Clamp Diameter: 22.2 mm
- High-concerned chemical: None
8. Safety Precautions
8.1. Operation Cautions
- Always be careful during use.
- Do not attempt to release the connector when the battery is powered on.
- Avoid hitting the display or control unit.
- Do not modify system parameters without understanding their function to prevent system disorder.
- If an error code appears, have the display repaired immediately, as the bike may not be ridable.
9. Support
For further assistance, technical support, or warranty inquiries, please contact Shengmilo customer service. You can often find contact information on the official Shengmilo website or through your original point of purchase.
Email support: support@shengmilo-bike.com