HITBOX TIG200P AC/DC

Contents

HITBOX TIG200P AC/DC Welder User Manual

Intelligent Inverter Welding Machine

1. Introduction

Thank you for choosing the HITBOX TIG200P AC/DC Welder. This intelligent inverter welding machine is designed for professional use, offering advanced technologies and multiple functions for various welding applications. It is suitable for welding aluminum, stainless steel, carbon steel, iron, copper, magnesium, and titanium alloys. This manual provides essential information on the safe use, maintenance, and operation of your welder. Please read it thoroughly before first use to ensure personal safety and optimal performance.

2. Safety Information

WARNING: Welding may result in injury to you and others. Please implement protection during welding. Observe all safety precautions.

2.1 General Safety Guidelines

  • Operate by trained professional only: Use welding labor protection supplies with approval of safety supervisory authority. Operators must be special workers with valid work permits. Do not maintain or repair the welder with power.
  • Electric shock - may result in serious injury or even death: Install grounding device according to application standard. Do not touch live parts with naked skin, wet gloves, or wet clothes. Ensure you are insulated from ground and workpiece. Confirm the safety of your working position.
  • Smoke - may be harmful to your health: Keep your head away from the smoke to avoid inhalation of waste gas. Ensure the working environment is well ventilated with exhaust or ventilation equipment.
  • Arc radiation - may hurt your eyes and burn your skin: Use proper welding mask and wear protective clothing to protect your eyes and body. Use proper mask or curtain to protect onlookers.
  • Improper use and operation may result in fire or explosion: Welding sparks may cause fire. Ensure no inflammables are near the welding position and pay attention to fire safety. Ensure a fire extinguisher is nearby and someone trained to use it. Do not weld closed containers. Do not use this machine for pipe thawing.
  • Hot workpiece can cause severe scald: Do not touch hot workpiece with bare hands. Cool the welding torch for a while after continuously working.
  • Excessive noise does great harm to people's hearing: Wear ear covers or other hearing protectors. Warn onlookers that noise may be hazardous.
  • Magnetic field can make cardiac pacemaker a bit wonky: People with cardiac pacemakers should stay away from the welding spot without first talking to a doctor.
  • Moving parts may injure your body: Keep away from moving parts (like the fan). Ensure all doors, panels, covers, baffle plates, and protective devices are closed and correctly located.
  • Seek professional support when trouble strikes: If issues arise during installation or operation, inspect according to this manual. If problems persist, contact your dealer or service center for professional support.

3. Symbol Explanation

The following symbols are used throughout this manual and on the machine to indicate important information:

SymbolDescriptionSymbolDescription
!Cautions in operationGround connection symbolGround connection
Items need special instructionArc force current
VIDEOSee more details in DVD (or video)VCurrent
It's forbidden to dispose electric waste with other ordinary waste.Frequency
***TSpot welding timeAPercentage
Rotary knobs allow for key-push operationHzTime
Diameter of Tungsten needles or electrodes%Pulse frequency
Parameters setting warningSWidth of pulse peak
Remote control mode or torch control modeGround connection
TIGArc force current
MMA
Welding gas related parameters

4. Product Overview

The TIG200P AC/DC is a numerical controlled inverter AC/DC welder featuring advanced technologies, multiple functions, and excellent performance. It is equipped with various welding modes including AC square wave argon arc welding, AC pulse argon arc welding, DC argon arc welding, DC pulse argon arc welding, DC flux-coated electrodes MMA, argon arc spot welding (DC, pulse or AC), and complex wave argon arc welding.

This welder is widely applied for delicate welding of various metal materials. Its unique electric structure with air channel design enhances heat dissipation, improving the duty cycle and preventing damage from dust. The overall streamline design integrates front and back panels seamlessly, providing a soft texture and pleasant appearance. Its optimized welding performance, high efficiency, small size, lightweight, and low cost make it suitable for both heavy industries and open-field operations.

HITBOX TIG200P AC/DC Welder front view
Front view of the HITBOX TIG200P AC/DC Welder.

5. Function Overview

5.1 Multi-Functions Design

  • Multiple Welding Modes: Supports various welding modes and torch control modes, including pedal remote and welding torch remote control.
  • Real-time Display: Convenient real-time display of welding current output status.
  • MMA Hot Start: Easier and more reliable MMA arc start.
  • VRD (Optional): Ensures operator safety in idle mode.
  • Anti-sticking (Optional): Lowers the machine's working intensity.
  • Self-adjustable Arc Force: Ensures good operation during long-distance welding.
  • HF Arc Start: Built-in pressurized arc ignition circuit, also applicable to TIG no-HF arc ignition.
  • Fan Intelligent Temperature Control: Prolongs the fan's lifespan.
  • Auto Memory: Automatically saves and recovers last welding parameters upon power off/on.

5.2 Performance Characteristics

  • IGBT Inverter Technology: Adopts 43 KHz inverting frequency and strong shock resistance IGBT for smaller size, lighter weight, and higher reliability. Greatly reduces copper and core loss, enhancing welding efficiency. Switching frequency is beyond audio frequency, minimizing noise.
  • Cutting-edge Control Technique: Advanced control scheme for various welding process requirements. New control technology reduces voltage spikes, improving reliability and efficiency. MCU intelligent digital control technology provides upgraded performances.
  • Applicable Electrodes: Compatible with various acid and basic electrodes with diameters from 0.6mm to 0.9mm.
  • Welding Quality: Easy arc starting, less spatter, stable current, and good shaping.
  • Optimized Auto Protection: Features protection against large voltage fluctuations, over-current, and over-heat, prolonging the welder's lifespan.
  • Excellent Consistency and Performance: Intelligent digital control technology makes the product insensitive to component changes, temperature, and humidity, ensuring consistent performance.
  • Easy Adjustments & Software Update: Main functions are realized by software, offering easy operation and high accuracy. Software upgrades require no circuit changes.
  • Friendly Interaction Interface: International diagram display for easy understanding and accurate operation.
  • High Quality MMA Welding: Excellent control algorithm improves MMA welding performance, providing easy arc start, stable current, minimum spatter, no sticking, good shaping, and self-adaptation to different cable lengths.
  • Highly Demanding Argon Arc Welding: Optimized digital CC adjustment technology ensures low noise and stable arc. Accurate control technology provides convenient operation for welding current. Supports 2T/4T/spot welding.
  • Remote Control: Capable of pedal remote control, allowing real-time welding current control up to 10m.

6. Technical Parameters

ParameterValue
Supply voltage (VAC)Single phase AC220V±15% 50/60Hz
Input frequency (Hz)50/60Hz
Rated input peak current (A)30A
Power capacity (KVA)6KVA
Rated output MMA current (A)160A
Rated output TIG current (A)200A
Output current MMA range10~160A
Output current TIG range5~200A
Arc force current range0-40
No load voltage (With VRD)56V
No load voltage (Without VRD)9V
Pre-blow time (S)0.1-10
Initial current (A)5-200
AC output frequency (Hz)20~250
Balance (%)15-85
Fall time (S)0-15
Post-blow time (S)0.5-15
Background current (A)5~200
Pulse frequency (Resolution 0.1Hz)0.2~20.0
Pulse frequency (Resolution 1Hz)21~200
Pulse duty factor (%) 0.2Hz~10Hz1~99
Pulse duty factor (%) 11Hz~200Hz10~90
Remote controlYES
Arc startHF oscillation
Efficiency (%)85
Duty circle (%)160A(ARC)-30% 200A(TIG)-25%
Power factor0.7
Insulation gradeB
Enclosure protection classIP21S
Weight (kg)9

7. Setup and Installation

Notice: Always turn off the power supply before any electrical connection operations. The machine has an IP21 enclosure protection grade; do not operate it in rain.

7.1 Machine Appearance and Panel Description

HITBOX TIG200P AC/DC Welder with accessories
HITBOX TIG200P AC/DC Welder and included accessories.

Front Panel Components:

  1. Operation panel: For function selection and parameter setting.
  2. Positive output terminal: To connect the electrode holder clamp.
  3. Negative output terminal: To connect the earth clamp or welding torch.
  4. Argon gas connector: For connecting the argon gas hose.
  5. Torch switch aviation socket: For connecting the TIG torch control cable.
  6. Trademark: HITBOX logo.
  7. Welding current adjusting knob: To adjust the output current.
  8. Handle: For carrying the machine.

Rear Panel Components:

  1. Power switch: Main power control switch.
  2. Caution label: Important safety warnings.
  3. Mains input: Power input cable connection.
  4. Radiator fan: For cooling the internal components.
  5. Argon inlet: Gas input for argon.
Detailed view of the welder's control panel and display
Detailed view of the welder's control panel and digital interface.

Control Panel Display:

The large LED display shows welding parameters and indicators. It includes:

  • Data Display: Shows current values for Amperage, Arc Force, Hot Start, etc.
  • Welding Parameters Indicators: Visual representation of welding waveforms and settings (Tup, Ip, Ib, Tdown, Tpost, AC Balance, AC Hz).
  • Mode Button: For selecting welding modes (AC TIG, DC TIG, MMA).
  • Pulse Switch Button: For activating pulse welding.
  • Function Button: For selecting specific functions.
  • Adjust Parameters Knob: To adjust selected parameters.
  • VRD Shift Switch: Voltage Reduction Device switch.
  • Spot Knob: For spot welding settings.

7.2 Installation Steps

  1. Connect Primary Power Line: Connect the primary power line to the appropriate voltage class (AC220V). Ensure the power line is connected to the right voltage class and is in fine contact with the terminal or socket to prevent oxidation.
  2. Check Input Voltage: Use a multimeter to verify the input voltage is within the fluctuation range.
  3. Connect Electrode Holder Cable (MMA): Insert the electrode holder cable plug into the front panel's upper "+" socket and screw it tightly clockwise.
  4. Connect Earth Clamp Cable: Insert the earth clamp cable plug into the front panel's lower "-" socket and screw it tightly clockwise.
  5. Ensure Good Grounding: Make sure the machine is properly grounded. There is a ground screw in the rear part of the machine; connect it with an earth cable (section ≥ 6mm²) to avoid static and electric shock.
  6. Connect Argon Gas Hose: Connect the argon gas hose to the gas inlet on the rear panel and secure it with a clamp. The other end connects to the Ar cylinder.
Connecting the argon gas hose to the welder
Connecting the argon gas hose to the welder's gas inlet.

7.3 TIG Welding Torch Assembly

The standard TIG torch model is WP-26K-E, with a maximum current of 200A and a rated current of 160A. It is air-cooled and uses an M10x1.0 gas connector with a 40% duty cycle.

Diagram showing the assembly of the TIG torch components
Diagram showing the assembly of the TIG torch components.

Assemble the TIG torch as shown in the diagram:

  1. Long handle cover
  2. Tungsten needle
  3. Tungsten electrode clamp
  4. Torch head
  5. Tungsten electrode clamp
  6. Ceramic nozzle
  7. Spearhead insulation cover

Ensure the tungsten electrode is in match with the panel's Tungsten electrode parameters and current parameters. When under AC welding mode, improper balance parameter may result in abnormal welding operation.

8. Operating Instructions

After proper installation, turn on the power switch. The welder will start normally, with the indicator lighting up and the fan working (fan operation is temperature-dependent).

8.1 Welding Mode Selection

Press the mode button when the machine is under no load to cycle through different welding modes. The mode switch is active only when the welder is in a no-load state.

Examples of different welding waveforms: DC Square Waveform and DC Pulse Waveform
Examples of different welding waveforms: DC Square Waveform and DC Pulse Waveform.

Available modes include:

  • Manual Arc Welding (MMA)
  • AC TIG
  • AC Pulse TIG
  • DC TIG
  • DC Pulse TIG

8.2 Welding Torch Control Mode Selection

When in TIG mode, press the torch control mode button to select between 2T, 4T, or Spot Welding modes. This button is also active only when the welder is in a no-load state.

8.2.1 2T (Two-Touch) Mode

Push the torch trigger to ignite the arc and gradually increase current. Release the trigger to gradually decrease current and stop the arc.

8.2.2 4T (Four-Touch) Mode

Push the torch trigger to ignite the arc and reach initial current. Release the trigger to gradually increase current. Push the trigger again to gradually decrease current to pilot arc value. Release the trigger again to stop the arc.

8.2.3 Spot Welding Mode

Push the torch trigger to ignite the arc and reach preset current. After the set spot welding time, the current gradually drops, and the arc stops.

8.2.4 Pedal Remote Control

Connect the pedal remote controller to the welder. Tread the pedal for 5 seconds in idle mode until the remote control indicator lights up. Release the pedal to enter remote control mode. The torch switch mode needs to be set to 2T. The welding current will be controlled by the pedal after successful arc ignition, up to the preset maximum current.

8.3 Welding Parameters Setting

Use the rotary encoder potentiometer to adjust welding parameters. Parameters can be set during no-load or in the middle of welding without affecting the weld.

8.3.1 MMA Welding Parameters

  • Current (I2): The welding current when the arc is burning.
  • Arc Force: Refers to the ascending slope of the current in short circuit. Adjust according to electrode diameter and technical requirements.
  • Arc Ignition Current (I1) and Arc Ignition Time (T1): The output current and duration when the arc is ignited.
Electrode Dia (mm)Recommended Welding Current (A)Recommended Welding Voltage (V)
1.630~6021~23
2.050~9022~24
2.580~12023~25
3.2100~14024~26
4.0140~16026~28

8.3.2 DC TIG Welding Parameters

  • Current (I3): Main welding current.
  • Initial Current (I1): Current when arc is ignited.
  • Pilot Arc Current (I5): Current in pilot arc state after current downslope.
  • Pre-flow Time: Time from trigger push to arc ignition, ensuring gas flow.
  • Post-flow Time: Time from current cut-off to gas valve closing, preventing weld bead oxidation.
  • Upslope Time (Tr): Time for current to rise from 0 to preset value.
  • Downslope Time (Td): Time for current to drop from preset value to 0.
Electrode Dia (mm)Recommended Welding Current (A)
1.05~30
1.620~90
2.045~135
2.570~180
3.2130~200

8.3.3 Pulsed TIG Welding Parameters

  • Peak Current (Ip): Maximum current during pulse.
  • Base Current (Ib): Minimum current during pulse.
  • Pulsed Frequency (1/T): Frequency of current pulses.
  • Pulse Duration Ratio (100%*Tp/T): Percentage of peak current time within a pulse period.

8.3.4 AC Square Wave TIG Welding Parameters

  • Initial Current (I0), Welding Current (I1) & Pilot Arc Current (I2): Similar to DC TIG, adjusted based on technical requirements.
  • Pulse Frequency (1/tp): Frequency of the AC square wave.
  • Cleaning Strength (100%*Tc/Tp): Percentage of cathode current holding in the AC period, crucial for breaking up oxidized layers on aluminum.

8.3.5 AC Pulsed TIG Welding Parameters

Similar to AC square wave TIG, but the welding current varies with a low-frequency pulse. The pulse frequency (0.5Hz to 5Hz) and pulse duration ratio (10% to 90%) can be adjusted.

Video demonstrating various welding modes (HF AC TIG, HF DC TIG, P-DC TIG, P-AC TIG, MMA) and setup steps.

9. Maintenance

WARNING: Maintenance requires professional knowledge. Ensure the power supply is cut off before uncovering the welding machine.

  • Check Connections: Periodically check inner circuit connections (especially plugs). Tighten loose connections and remove oxidation with sandpaper if present.
  • Moving Parts: Keep hands, hair, and tools away from moving parts like the fan to prevent injury or damage.
  • Clean Dust: Periodically clean dust with dry, clean compressed air. In heavy smoke/pollution environments, clean daily. Use appropriate pressure to avoid damaging small internal parts.
  • Protect from Moisture: Avoid rain, water, and vapor. If moisture infiltrates, dry the machine and check insulation before use.
  • Inspect Cables: Periodically check the insulation cover of all cables. Rewrap or replace if dilapidated.
  • Storage: If not used for a long time, store the machine in its original packing in a dry, ventilated indoor location without corrosive gas. Storage temperature: -25°C to +50°C. Humidity: ≤90%.

10. Troubleshooting

The following tables provide common malfunctions, their causes, and solutions. If problems persist, contact professional support.

10.1 MMA Common Malfunction Solutions

Malfunction PhenomenaCause AnalysisSolutions
Fan doesn't work or abnormal revolving speedTemperature is too low or fan is broken.Operate welder for a while; if still not working, change the fan.
Difficult arc ignitionLow arc ignition current or short ignition time.Adjust (increase) the arc ignition current and time.
Over arc ignition or over-size molten poolIgnition current is too big or ignition time is too long.Adjust (decrease) the arc ignition current and time.
Abnormal arcPoor power cable connection.Ensure well connection of power cable.
Sticking electrodeLow arc force current.Adjust (increase) the arc force current.
Burning electrode holderElectrode holder rated current is too low.Change to a larger current electrode holder.
Easy arc breakingNetwork voltage is too low.Operate when network voltage is back to normal.
Other failuresPlease contact service personnel.

10.2 TIG Common Malfunction Solutions

Malfunction PhenomenaCause AnalysisSolutions
No output current when torch switch is onSome TIG function allows welding ending while torch switch is still on.Release torch switch and restart welding.
Welding circuit disconnection.Check the circuit and reconnect.
No arc ignition when turning on the torch switch (HF arc ignition mode)Poor connection of welding torch switch.Reconnect and tighten the welding torch.
Over-wide spark gap.Adjust the spark gap (about 0.8mm).
Over burning of tungsten electrodeReverse connection of welding torch and ground cable.Exchange the two plugs' position.
Clearing intensity is too big.Decrease the clearing intensity.
Black welding spotWelding spot is poorly protected and has oxidation.1. Make sure the argon cylinder valve is open and has enough pressure. If internal pressure is lower than 0.5Mpa, refill the gas.
2. Check if the argon flow is normal or not. You may choose different flow according to different welding current. Min argon flow of 5L/min is suggested.
3. Make sure the gas circuit is well sealed and gas purity is good.
4. Check if there is strong airflow in the working environment.
Difficult arc ignition, easy arc breaking, severe oxidation of tungsten electrodesPoor quality tungsten electrode.1. Change good quality tungsten electrodes.
2. Remove the oxidation layer.
3. Prolong the post-flow time to avoid tungsten oxidation.
4. Adjust the spark gap (around 0.8mm).
Unstable welding current during weldingBig fluctuation of network voltage or poor connection with power grid.1. Make sure the power grid is normal and well connected.
2. Use different power cables for severe interference equipment.
Other failuresPlease contact service personnel.

10.3 Alarm and Solutions

TypeAlarmError codeWelder reactionReasonSolutions
OverheatOverheat indicator lights up and there is alarm soundE-1Temporary close of main circuitOver-working of main circuitDo not power off; restart welding when the overheat indicator stops lighting up.
Under-voltageDisplay error code and alarm soundE-2Permanent close of main circuitPower grid under-voltage (lower than 160VAC)Restart the welder; if warning still remains due to continuous power grid undervoltage, please wait.
Over-voltageDisplay error code and alarm soundE-3Permanent close of main circuitPower grid overvoltage (more than 270VAC)Shut off the welder and restart. If warning remains due to continuous power grid overvoltage, please wait.
Abnormal Internal CircuitDisplay error code and alarm soundE-4Permanent close of main circuitLoad current is too big or main power device is under over-current protection.Restart welder. If the warning still remains, please contact professional maintenance personnel.

11. User Tips

  • Display Visibility: The large LED display is very bright and easy to see, even when wearing a welding mask.
  • Hose Connections: Ensure all gas hose connections are secure and the correct diameter hose is used to prevent gas leaks and ensure proper shielding.
  • Parameter Adjustment: Take advantage of the precise parameter adjustment knob for fine-tuning your welding settings to achieve optimal results for different materials and thicknesses.

12. Wiring Diagram

For advanced troubleshooting or internal inspection, refer to the complete wiring diagram below. This diagram illustrates the internal connections and components of the TIG200P AC/DC welder.

Detailed internal wiring diagram for the TIG200P AC/DC welder
Internal wiring diagram of the HITBOX TIG200P AC/DC Welder.

13. Support and Warranty

For any technical assistance, warranty claims, or further information, please contact the manufacturer or your authorized dealer. The manufacturer is Shenzhen Unitweld welding and Motor Co., Ltd.

This product is under continuous improvements; therefore, there might be differences in some respects except for functions and operation. Your understanding is much appreciated.

© 2024 HITBOX. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.