Skydroid C14 Pro

Contents

Skydroid C14 Pro User Manual

Small HD Three-Axis Four-Light Stabilized Gimbal

Version 1.0

1. Product Introduction

The C14 Pro is a compact HD four-light mechanically stabilized gimbal. It utilizes a new generation imaging chip and integrates distortion-free HD short-focus and long-focus cameras with an effective pixel count of 5 million. It boasts robust 2K video recording and photo-taking capabilities, supporting 100x hybrid electronic zoom (59x from the short-focus + 41x from the long-focus), which brings distant scenery into sharp focus.

Equipped with a thermal imaging camera with a resolution of 640x512, it offers a wide field of view and clear images, enabling long-distance observation of various heat sources. In combination with the laser ranging module, the effective ranging distance can reach up to 1.2 kilometers. The industrial-grade three-axis stabilization structure is adopted, which significantly reduces frame jitter, keeping the image in a stable state at all times. It can be applied in fields such as fire rescue, animal protection, and security monitoring.

Skydroid C14 Pro Gimbal

Figure 1: Skydroid C14 Pro Gimbal

2. Product List

The following items are included in the product package:

ItemQuantityDescription / Image
C14 Main Body1C14 Main Body
Gimbal fixing screws (M2.5*6)4Gimbal fixing screws
Ethernet port power cable1Ethernet port power cable
32G Kingston Memory Card (Pre-installed)132G Kingston Memory Card
Card reader1Card reader

3. Product Overview

This section details the interfaces and definitions of the C14 Pro gimbal.

C14 Pro Gimbal Interface Diagram

Figure 2: Gimbal Interface and Definition Diagram

The diagram illustrates the various ports and their functions, including the UART interface (TX, RX, GND, VIN, NC, TD+, TD-, RD+, RD-) and the TF card slot for storage.

4. Specifications

4.1 C14 Pro General Parameters

ParameterValue
Video output signal interfaceEthernet Port
Control signal input interfaceEthernet Port
Operating Voltage12V~80V
Operating Current12V 350mA
Operating Temperature-10°C ~ +60°C
Storage Temperature-20°C ~ +60°C
Weight199g
Dimensions (L×W×H)65.5mm × 68.57mm × 92mm
Controllable angle range (Pitch)-110° to +75°
Controllable angle range (Yaw)-165° to +165°
Controllable angle range (Roll)-40° to +40°
Stabilization Method3-axis Mechanical Stabilization
Angular Jitter (Hovering)±0.01°
Angular Jitter (Flying)±0.02°
Video OutputRTSP
Control MethodUDP
Ceiling-mounted/Inverted-mounted modeSupported
Global centering/One-key downward/Yaw centeringSupported

4.2 Visible Light Camera Parameters

ParameterValue
Lens pixel5 million
Video resolution for card recording2880*1620
CMOS size1/2.7
Video storage formatTS
Zoom Ratio100x Hybrid Electronic Zoom
Photograph resolution2880*1620
Video transmission resolution(1280*720)@30fps
Photograph storage formatJPG
Supported Memory Card TypeMicroSD Card (Max. 128GB)
Supported file systemsFAT32

4.3 C14 Short-focus Lens Parameters

ParameterValue
ApertureF=2
Focal Length3.2mm
HFOV/VFOV/DFOV80°/61°/93°
Zoom Ratio59x

4.4 C14 Long-focus Lens Parameters

ParameterValue
ApertureF=2.4
Focal Length25mm
HFOV/VFOV/DFOV14.7°/11.1°/18.3°
Zoom Ratio41x

4.5 C14 Thermal Imaging Camera Parameters

ParameterValue
Resolution640*512
ApertureF=1.0
Focal length11mm
Pixel pitch10μm
Frame rate30Hz
Response band8~14µm
Thermal time constant< 12ms
Field of view angle32.84°x26.35°
Detection range1.1km

4.6 C14 Laser Ranging Parameters

ParameterValue
Wavelength905nm
Detection range5M~1200M
Ranging capability (Visibility ≥ 10km, Humidity ≤ 60%, Building target)≥1200 m
Ranging capability (Visibility ≥ 10km, Humidity ≤ 60%, 1.7m × 0.5m Humanoid target)≥500 m
Ranging Accuracy (≤300m)≤±0.25m
Ranging Accuracy (300m < L ≤ 1000m)≤±0.5m
Ranging Accuracy (> 1000m)≤±2m
Laser divergence angle5mrad
Measurement FrequencySingle, 1Hz, 2Hz
Transmitting ApertureΦ7mm
Accuracy rate≥99%
Receiving ApertureΦ7mm
False Alarm Rate≤2%

5. Installation and Debugging

5.1 Screw Holes and Spacing

The schematic diagram of screw holes and their spacing is as follows:

Gimbal Screw Hole Diagram

Figure 3: Gimbal Screw Hole and Spacing Diagram

  • The screw specifications for the pan-tilt are M2.5*6, and the quantity is 4.
  • Do not hang the gimbal on the aircraft when it is not in use. Long-term hanging will accelerate the deformation of the shock-absorbing balls, resulting in a decline in shock-absorbing performance and the appearance of the "jello" effect.
  • When installing the gimbal, the shock-absorbing plates must be kept absolutely perpendicular and parallel to each other. Incorrect installation will cause the shock-absorbing balls to deform, leading to a decrease in shock-absorbing performance and failure of self-inspection.

5.2 Gimbal Working Modes

You can set the gimbal to either top-mounted (hoisting mode) or inverted-mounted (flip mode) in the FPV settings.

Gimbal Working Modes Interface

Figure 4: FPV Software - Operating Mode Selection

  • Note: The hoisting mode is the default setting at the factory. Do not power on when it is installed in an inverted way.
  • Please place the gimbal correctly according to the working mode. Incorrect placement may cause damage to the gimbal motor.

5.3 Gimbal Wiring Diagram and Explanation

The following diagram illustrates the wiring connections between the C14 gimbal and the GR01 module.

Gimbal Wiring Diagram

Figure 5: C14 Gimbal Wiring Diagram

ConnectionDetails
PowerRed JST-2P male connector. Power supply: 7.2V-80V (DC power supply or 2S-18S lithium battery).
Ethernet cable (for signal transmission)Network IP signal: RX-, RX+, TX-, TX+.
Visible light video outputRTSP stream rtsp://192.168.144.108:554/stream=1
Thermal imaging video outputRTSP stream rtsp://192.168.144.108:555/stream=2

5.4 Usage of C14

Install and open the latest version of the Gimbal FPV software on the remote control. Software download address: http://file.skydroid.xin/SkydroidCameraFPV.apk

  1. Gimbal Startup: After the gimbal is properly installed and fixed, power it on. The gimbal will start up. Please wait until the startup is complete.
  2. Open Gimbal FPV Software: Select the C14, and click to enter.
FPV Software Main Interface

Figure 6: FPV Software Main Interface

5.5 Gimbal Parameter Settings

Gimbal control, calibration, fine-tuning, operating modes, speed, and color palette can be configured in the parameter settings.

5.5.1 Gimbal Control

Click Parameter Settings -> Pan-tilt Control. There are target following and three control methods to choose from, and multiple methods can be selected simultaneously (Target following cannot be used simultaneously with gesture control).

  1. AI Target Following: After selecting the target to follow, the C14 will automatically track the target.
AI Target Locking Example

Figure 7: AI Target Locking in action

  1. Virtual Joystick Control: Use the virtual joystick to control the pan and tilt of the gimbal. It also supports functions such as one-key return to the center.
  2. Gesture Control: Control the pan and tilt of the gimbal by swiping the screen.
  3. Remote Control Channel Control: Control the pan and tilt of the gimbal, as well as functions like taking photos and recording videos through customizing the remote control channels. (The remote control channels can be checked through the Remote Control Assistant -> Rudder Volume View.)

5.5.2 Gimbal Calibration

Temperature Calibration: Calibrate the temperature of the gimbal during operation to prevent malfunction caused by excessive temperature differences between the ambient environment and the IMU's operating temperature.

5.5.3 Correction of Pot Lid Effect

Note: The lid effect has been calibrated upon delivery. Due to the special calibration method, do not calibrate it yourself unless necessary. Before calibration, please contact the relevant technicians from Skydroid for confirmation.

Calibration method:

  1. Power on the C14 and let it preheat for more than five minutes.
  2. Select a panel with a flat surface, uniform temperature, even frosting, and low reflectivity.
  3. Move the C14 close to and make contact with the target surface. It is optimal when the imaging of the target surface covers the entire field of view without any stray light entering.
  4. Click "Calibrate the Lid Effect", and the calibration is successful when the screen turns into a uniform gray.
Pot Lid Calibration Target Surface

Figure 8: Schematic diagram of the calibration target surface for the lid effect

5.5.4 Operating Modes

The gimbal can be set to either top-mounted or inverted-mounted mode. Please mount the gimbal correctly according to the operating mode. Incorrect mounting will cause damage to the gimbal motor.

5.5.5 Gimbal Speed

The control speed of the gimbal has two modes: constant speed mode and variable speed mode.

5.5.6 Color Palette

It is possible to adjust the imaging effect of the thermal imaging camera, with a total of eleven options available, including White Hot, Sepia, Ironbow, Rainbow, Night, Aurora, Red Hot, Jungle, Medical, Black Hot, and Glory Hot.

5.5.7 Laser Ranging

Click the ranging button to perform a single laser ranging. The effective ranging range is 5m to 1.2 km.

5.5.8 Set Encoding Mode

You can set screen flipping, view the camera version number, and set OSD display.

5.5.9 Firmware Upgrade

You can upgrade the gimbal firmware and camera firmware. Do not cut off the power or exit the upgrade interface during the upgrade process. (When upgrading the camera firmware, a TF card must be inserted into the C14.)

6. Gimbal Dimensions and Angle Markings

The following diagram provides the dimensions and angle markings for the C14 Pro gimbal.

Gimbal Dimensions Diagram

Figure 9: Gimbal Dimensions and Angle Markings

Due to version evolution and changes in customer requirements, relevant commands and controls may be subject to alteration. Please contact Skydroid Technology Co., Ltd. to obtain the latest information and technical support. As the product is updated and upgraded, parameters such as dimensions and weight may change. Your understanding is highly appreciated.

7. Precautions

To protect you, others from harm, and safeguard your device from damage, please read all the following information before using your device.

  1. Do not direct components to high-intensity radiation sources such as the sun.
  2. The ideal operating ambient temperature ranges from -10℃ to +60°C.
  3. Do not touch the device and cables with wet hands.
  4. Do not bend or damage the connecting wires.
  5. Do not clean your device with thinner.
  6. Do not unplug or plug in other cables without disconnecting the power supply.
  7. Do not misconnect the attached cables to avoid damaging the device.
  8. Be careful to prevent static electricity.
  9. Do not disassemble the device. If there is a malfunction, please contact our company and let professionals carry out the repair.

8. User Tips

No specific user tips were provided in the source data. Always refer to the latest official documentation for best practices.

9. Warranty and Support

9.1 After-Sales Service Terms

These terms apply to products manufactured by Skydroid and sold by authorized Skydroid dealers.

  1. If a non-human factor quality problem is verified by Skydroid technicians within one week of purchase, Skydroid will cover shipping fees for repair. Between one week and one year, user and Skydroid will share shipping fees.
  2. Purchase voucher and warranty card or online transaction record are required for repairs.
  3. Within 7 days of purchase, if Skydroid products have quality problems not caused by human activities under normal use, and the appearance is undamaged, users can negotiate free replacement of the same model with local dealers using the warranty card and purchase proof. Dealers must inform Skydroid of the replacement.
  4. Skydroid provides lifelong after-sales service. Non-human factor quality problems are guaranteed free of charge within one year. For man-made damage, modification, dismantling, or exceeding the one-year warranty period, the user pays round-trip shipping and maintenance fees.
  5. To protect your rights, complete the warranty card and obtain a purchase voucher.
  6. Repaired products are returned within 15 working days with a repair report.
  7. These after-sales terms are limited to Skydroid products sold in Chinese Mainland.

9.2 Contact and Latest Information

For after-sales problems for Hong Kong, Macao, Taiwan, and overseas customers, please email: sales01@skydroid.xin. Specific rules depend on the situation.

For the latest information and technical support, or to download the most current version of the manual, please visit the official website's Resource Download Center: https://www.skydroid.xin/#/downloadCenter

Warm reminder: Please read the operation manual carefully before use!

This manual may not be the latest version. For the latest version, please go to the Official Website's Resource Download Center.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.