intelamp YL005-18GP20

Contents

Intelamp YL005-18GP20 Outdoor Solar Security Light

Model: YL005-18GP20 | Brand: Intelamp

Introduction

The Intelamp YL005-18GP20 is a powerful outdoor solar security light designed for efficient and long-lasting illumination of garages, courtyards, gardens, and other outdoor spaces. Built with high-quality materials and advanced technology, this light offers superior brightness, extended runtime, and intelligent sensing capabilities.

Intelamp specializes in developing and producing high-quality, long-life solar lights. Our commitment to quality ensures that our products are durable and reliable, saving you time, energy, and maintenance costs compared to cheaper alternatives.

Key features include:

  • Efficient Solar Charging: Adopts TOPCon 3rd generation components with 24%+ charging efficiency. The 20W solar panel (5V/4000mA) can fully charge the 20000mAh LiFePO4 battery in as little as 5 hours under direct sunlight, providing over 12 hours of all-night illumination.
  • High Brightness: Equipped with 210 high-quality LED beads, delivering 4000LM brightness and 6500K white daylight. This surpasses similar products, offering ample light for reading and writing within 5 meters and clear visibility for walking up to 20 meters.
  • Intelligent Mutual Control: When one Intelamp solar light is activated, it emits a signal that triggers all other Intelamp solar lights within a 66ft (20m) radius to illuminate, creating a connected and proactive lighting system.
  • Dual Sensing & Wide Angle: Features two motion sensors for enhanced sensitivity and a 240° lighting angle from dual wide-angle illumination faces.
  • Durable Design: Made from high-quality ABS material with an IP65 waterproof rating, allowing it to withstand various outdoor weather conditions. The solar panel's shade helps reduce the lamp's temperature in hot summers, extending battery and product lifespan.

Product Overview

Intelamp Solar Security Light components: solar panel, main light unit, remote control, and separate motion sensor.
This image displays the main components of the Intelamp Solar Security Light: a large solar panel, the primary light unit with integrated motion sensors, a remote control for operation, and a smaller, separate motion sensor unit.
Diagram showing dimensions of Intelamp solar panel (16.1in x 13in), light unit (9.3in x 7.1in), and small sensor (1.6in x 2.4in), with a 16.4ft cable connecting the solar panel to the light.
This diagram provides key dimensions for the solar panel (16.1 x 13 inches), the main light unit (9.3 x 7.1 inches), and the small sensor (1.6 x 2.4 inches). It also highlights the 16.4-foot cable for flexible installation of the solar panel.
This video provides a visual demonstration of the Intelamp solar light, showcasing its wide illumination, dual motion sensors for enhanced detection, the powerful 20000mAh battery, efficient 20W solar panel, and the innovative linked lighting system that activates multiple lights simultaneously.

Setup

Package Contents:

  • 1 x Intelamp Solar Lamp Unit
  • 1 x Remote Control
  • 1 x Separate Sensor Unit (if applicable to your model)
  • Mounting Hardware (screws, anchors)

Installation Guidelines:

The Intelamp solar light offers flexible installation with two main methods: Pole Mount and Wall Mount. The solar panel is connected to the light unit via a 16.4ft (5m) cable, allowing for optimal placement of both components.

Illustrations showing two installation methods for the Intelamp solar light: Pole Mount, where the solar panel and light are attached to a pole, and Wall Mount, where they are attached to a wall.
This image illustrates the two primary installation methods: Pole Mount, where the solar panel and light unit are affixed to a pole, and Wall Mount, where they are secured to a vertical surface.
  1. Choose a Location:
    - For the solar panel: Select a spot that receives at least 5 hours of direct sunlight daily to ensure optimal charging. Avoid shaded areas from trees, buildings, or other obstructions.
    - For the light unit: Mount the light at an installation height of 10-12 feet (approximately 3-3.6 meters) for optimal illumination coverage. Ensure the area where motion detection is desired is within the sensor's range.
  2. Mount the Solar Panel: Secure the solar panel using the provided mounting hardware. Adjust its angle to face the sun directly for maximum exposure.
  3. Mount the Light Unit: Attach the light unit to your chosen surface (wall or pole) using the appropriate mounting hardware. Ensure it is securely fastened.
  4. Connect the Solar Panel: Connect the 16.4ft cable from the solar panel to the light unit. Ensure the connection is secure and waterproof.
  5. Position the Sensor Unit (if separate): If your model includes a separate sensor unit, position it in an area where it can effectively detect motion within a 180° wide-angle range, ideally linked to the main light unit.

Operating Instructions

The Intelamp solar light is operated using the included remote control. Familiarize yourself with the remote's functions to customize your lighting experience.

Remote Control Functions:

Diagram of the remote control for the Intelamp solar light, showing buttons for Power (ON/OFF), Sensor mode (30s, 3m, 10m, Dim, Off), Lighting mode (2H, +1H, 6H, Dim, Off), and Bright adjustment (60%, 80%, 100%).
This image details the remote control functions, including Power ON/OFF, Sensor mode settings (30s, 3m, 10m high brightness after induction, or Dim/Off), Lighting mode settings (2H, +1H, 6H for automatic night lighting, or Dim/Off after programmed time), and Brightness adjustment (60%, 80%, 100%).
  • Power (ON/OFF): Turns the light on or off.
  • Sensor Mode (30s / 3m / 10m): Sets the duration for high brightness after motion detection. The light will remain at high brightness for 30 seconds, 3 minutes, or 10 minutes, then transition according to the selected sensor mode (dim or off).
  • Lighting Mode (2H / +1H / 6H): Sets the duration for automatic lighting at night. The light will operate for 2 hours, 3 hours (2H + 1H), or 6 hours.
  • Dim / Off (under Sensor Mode): Determines the light's behavior after the high-brightness duration in sensor mode. 'Dim' means it will dim to a lower brightness (e.g., 20%), while 'Off' means it will turn off completely.
  • Dim / Off (under Lighting Mode): Determines the light's behavior after the programmed lighting duration. 'Dim' means it will dim to a lower brightness (e.g., 20%) and stay on until dawn, while 'Off' means it will turn off completely.
  • Bright Adjustment (60% / 80% / 100%): Adjusts the overall brightness level of the light.

Lighting Modes Explained:

The Intelamp solar light offers various operational modes to suit your needs:

  1. Sensor Mode 1 (Dim-to-Bright):
    - When motion is detected, the light brightens to 100% for the set duration (30s, 3min, or 10min).
    - After the set duration, if no further motion is detected, the light dims to 20% brightness and stays on until dawn or until motion is detected again.
    Three panels showing Sensor Mode 1 operation: light off, light at 100% brightness when motion is detected, and light dimming to 20% brightness after motion stops.
    Sensor Mode 1: When motion is detected, the light brightens to 100% for a set duration (30s, 3min, or 10min), then dims to 20% brightness until motion is detected again or dawn.
  2. Sensor Mode 2 (Off-to-Bright):
    - When motion is detected, the light brightens to 100% for the set duration (30s, 3min, or 10min).
    - After the set duration, if no further motion is detected, the light turns completely off until motion is detected again or dawn.
    Three panels showing Sensor Mode 2 operation: light off, light at 100% brightness when motion is detected, and light turning off after motion stops.
    Sensor Mode 2: When motion is detected, the light brightens to 100% for a set duration (30s, 3min, or 10min), then turns completely off until motion is detected again or dawn.
  3. Lighting Mode 3 (Constant Dimming):
    - The light automatically activates at a set brightness (e.g., 80%) from dusk.
    - It then gradually dims to a lower brightness (e.g., 20%) and stays on at that level until dawn.
    Two panels showing Lighting Mode 3 operation: light at 80% brightness at dusk, and light dimming to 20% brightness until dawn.
    Lighting Mode 3: The light automatically activates at a set brightness (e.g., 80%) from dusk, then dims to a lower brightness (e.g., 20%) and stays on until dawn.
  4. Lighting Mode 4 (Constant On, then Off):
    - The light automatically activates at a set brightness (e.g., 80%) from dusk.
    - It then turns completely off until dawn.
    Two panels showing Lighting Mode 4 operation: light at 80% brightness at dusk, and light turning off until dawn.
    Lighting Mode 4: The light automatically activates at a set brightness (e.g., 80%) from dusk, then turns completely off until dawn.

Intelligent Mutual Control (Linked Lighting):

This feature allows multiple Intelamp solar lights to work together. When one light's motion sensor is triggered, it sends a signal to other linked lights within a 100ft (30m) radius, causing them to activate simultaneously. This creates a seamless path of light as you move through your property.

Illustration of multiple Intelamp solar lights linked together, illuminating a street and houses, with a person walking a dog. Shows a 100ft linking range.
This image demonstrates the 'Lights Link Together' feature, where multiple Intelamp solar lights communicate wirelessly to illuminate a larger area, such as a street or multiple houses, with a range of up to 100 feet (30 meters).
Illustration of a person walking a dog, activating a small sensor unit which then triggers nearby Intelamp solar lights to turn on, showing a 100ft linking range.
This illustration highlights the 'Sensor Links Lights to Turn On' functionality. A separate sensor unit detects motion and wirelessly activates connected Intelamp solar lights within a 100-foot (30-meter) radius, providing proactive illumination.

Maintenance

To ensure the longevity and optimal performance of your Intelamp solar light, follow these simple maintenance tips:

  • Clean Solar Panel: Regularly wipe the surface of the solar panel with a soft, damp cloth to remove dust, dirt, leaves, or snow. A clean panel ensures maximum sunlight absorption and charging efficiency.
  • Check for Obstructions: Periodically inspect the area around the solar panel and light unit for any new obstructions (e.g., growing tree branches, new structures) that might block sunlight or interfere with motion detection.
  • Battery Care: The built-in LiFePO4 battery is designed for long life. Avoid prolonged storage of the light in a completely discharged state. If storing for an extended period, ensure it is fully charged first.
  • Inspect Connections: Occasionally check the cable connection between the solar panel and the light unit to ensure it remains secure and free from damage.
  • General Cleaning: Clean the light unit itself as needed to maintain its appearance and ensure clear light output.

Troubleshooting

If you encounter issues with your Intelamp solar light, try the following troubleshooting steps:

  • Light Not Turning On at Night:
    - Ensure the light is switched ON using the remote control.
    - Verify the solar panel is receiving at least 5 hours of direct sunlight daily. Relocate if necessary.
    - Check for any obstructions blocking the solar panel or the light sensor.
    - The battery might be low. Allow several sunny days for a full charge.
  • Light Not Detecting Motion:
    - Ensure the light is in a Sensor Mode (Mode 1 or Mode 2).
    - Check if the motion sensors are clean and free from obstructions.
    - Verify the installation height is within the recommended 10-12 feet range for optimal sensor performance.
    - Test the sensor by walking directly in front of it.
  • Light Not Staying On Long Enough:
    - The battery may not be fully charged. Ensure the solar panel gets sufficient direct sunlight.
    - The selected lighting mode or sensor duration might be too short. Adjust settings using the remote control.
    - Extreme cold weather can affect battery performance.
  • Linked Lights Not Activating:
    - Ensure all lights are within the 100ft (30m) linking range.
    - Check that all lights are powered on and in a compatible sensor mode.

Specifications

FeatureSpecification
Model NumberYL005-18GP20
Brand Nameintelamp
Power SourceSOLAR
OriginMainland China
StyleModern Style
Bulbs IncludedYes
DimmableYes
Solar Cell TypeLithium battery (LiFePO4)
Protection LevelIP65
Body MaterialABS
High-concerned chemicalNone
Installation MethodSelf-contained (with remote solar panel)
Batteries IncludedYes
Battery Capacity20000mAh
Solar Panel20W Topcon, 5V/4000mA
Charging Efficiency24%
Brightness4000LM
Color Temperature6500K White Daylight
LED Beads210 pcs
Light Angle180°
Sensor Sensing Range180° wide-angle detection
Lighting Angle240°
Product Dimensions44 x 35 x 9.5 cm
Item Weight3.7 kg
Solar Panel Cable Length16.4 ft (5m)
CertificationsCE, FCC, GS, LVD, ROHS, UL
Package Includes1 x Solar Lamp, 1 x Remote Control, 1 x Sensor Unit

User Tips

  • Optimize Solar Panel Placement: Even a small amount of shade can significantly reduce charging efficiency. Ensure your solar panel is in a location that receives unobstructed direct sunlight for the majority of the day, especially during peak sun hours.
  • Test Motion Sensor: After installation, test the motion sensor's range and sensitivity by walking through the intended detection area. Adjust the light's position or sensor unit if coverage is not adequate.
  • Remote Control Best Practices: Keep the remote control in a safe, dry place. Point it directly at the light unit when making adjustments for reliable communication.
  • Linked Lighting Setup: When using multiple lights with the intelligent mutual control feature, strategically place the sensor unit (if separate) or one of the main light units in a high-traffic area to trigger the entire network effectively.
  • Seasonal Adjustments: In winter or during prolonged cloudy periods, the light may not receive enough sunlight to fully charge. Consider adjusting the brightness or mode to conserve battery life if consistent full brightness is not critical.

Warranty and Support

For any questions, technical assistance, or warranty claims, please contact Intelamp customer support. Refer to your product packaging or the seller's website for specific warranty terms and contact information.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.