JINKA S490

Contents

Jinka S490 Automatic Label Cutting Machine

User Instruction Manual

1. Introduction

The Jinka S490 is an advanced automatic label cutting machine designed for precision and efficiency in label production. Featuring an auto-feeding mechanism, a high-definition camera for accurate identification, and a user-friendly touch screen interface, this desktop plotter cutter is suitable for various label cutting applications. Its robust design and brand servo motor ensure low noise operation and fast cutting speeds.

Jinka S490 Label Cutting Machine, front view with paper trays extended

Figure 1: Jinka S490 Label Cutting Machine with extended trays

2. Specifications

Below are the detailed technical specifications for the Jinka S490 Label Cutting Machine:

Feature Specification
ModelS490
Material Width185-350mm
Material Length150-500mm
Max. Cutting Speed1200mm/s
Max. Plotting/Cutting Force500g
Max. Paper Weight350g/㎡
Display LanguageEnglish / Chinese
DriverStepper motor
Control Panel & Display4.3-inches touch screen
Memory32M
CarriageAlloy single position carriage with CCD
InterfaceUSB + USB flash + TCP (Wifi optional)
Power60W
Power SupplyAC85V-AC264V, 50Hz/60Hz
Operating Environment Temperature+5℃ to +35℃
Operating Environment Humidity30%-70% relative humidity
CommandHPGL
Packing Size865*530*430mm
Net Weight / Gross Weight29KG / 32KG
OriginMainland China (Anhui, China)
Voltage110V/220V
Cache Capacity4Mb
Paper Feed Width490mm
Cutter Pressure10-600g
Cutting Width350mm
Cutting LengthVinyl's Length
Repeat Cutting1-500 Times
Size (Machine)820*560*455mm
SoftwareAnycut / Coreldraw
KeypadTouch screen
Feed RollerGrit roller
ColorGrey

3. Setup Guide

  1. Unpacking: Carefully remove the cutting machine from its packaging. Retain all packaging materials for future transport or storage.
  2. Placement: Place the machine on a stable, level surface in an environment with a temperature between +5℃ and +35℃ and relative humidity between 30%-70%. Ensure adequate space around the machine for paper feeding and output.
  3. Power Connection: Connect the power cable to the machine and then to a compatible AC85V-AC264V, 50Hz/60Hz power outlet.
  4. Paper Tray Setup: Extend the auto-feeding paper trays as shown in Figure 1. The input tray is designed to hold 100-150 sheets of paper.
  5. Software Installation: Install the cutting software (Anycut / Coreldraw) on your computer. Follow the software's installation instructions.
  6. Connect to Computer: Connect the cutting machine to your computer using a USB cable, USB flash drive, or via TCP (Ethernet). Wi-Fi connectivity may also be an option if your model supports it.
Jinka S490 Label Cutting Machine, side view with paper trays extended

Figure 2: Side view of the Jinka S490 with trays

4. Operating Instructions

  1. Power On: Turn on the machine using the power switch. The 4.3-inch touch screen will illuminate.
  2. Load Material: Place your label sheets into the auto-feeding input tray. Ensure the material is aligned correctly with the grit rollers. The machine supports material widths from 185-350mm and lengths from 150-500mm.
  3. Software Preparation: Open your cutting software (Anycut or Coreldraw) on your computer. Import or design your label cutting file.
  4. Send to Cutter: From your software, send the cutting job to the Jinka S490. The machine uses HPGL commands.
  5. Touch Screen Control: Use the touch screen control panel to adjust settings such as cutting speed (up to 1200mm/s) and cutting force (up to 500g) if needed. The UI is designed for ease of use.
  6. Automatic Identification: The integrated HD camera will accurately identify registration marks on your labels, ensuring precise cuts without material limitations.
  7. Start Cutting: Confirm settings and initiate the cutting process from the touch screen or software. The auto-feeding mechanism will feed sheets one by one.
  8. Repeat Cutting: For multiple identical cuts on a single sheet, utilize the repeat cutting function (1-500 times).
  9. USB Flash Drive Operation: If using a USB flash drive, you can load cutting files directly. The machine supports reading QR codes to locate files on the USB flash drive.
Close-up of the touch screen control panel

Figure 3: Touch screen control panel

Close-up of the feeding rollers and cutting mechanism

Figure 4: Feeding rollers and cutting mechanism

Examples of labels cut by the machine

Figure 5: Examples of finished label cuts

5. Maintenance

  • Regular Cleaning: Keep the machine, especially the feeding rollers and cutting area, free from dust and paper debris. Use a soft, dry cloth.
  • Blade Inspection and Replacement: Periodically inspect the cutting blade for sharpness. A dull blade can lead to poor cut quality. Replace the blade as needed following manufacturer guidelines.
  • Software Updates: Ensure your cutting software and machine firmware are up to date to benefit from performance improvements and new features.
  • Roller Maintenance: Check the grit rollers for wear or damage. Clean them gently to ensure proper material feeding.
  • Environmental Control: Maintain the recommended operating environment (temperature and humidity) to prevent issues caused by extreme conditions.

6. Troubleshooting

  • Machine Not Powering On: Check the power cable connection and ensure the power outlet is functional. Verify the power switch is in the 'On' position.
  • Poor Cut Quality: Inspect the cutting blade for dullness or damage and replace if necessary. Ensure the material is loaded correctly and the cutting force is appropriate for the material type and thickness.
  • Material Feeding Issues: Check for any obstructions in the paper path. Ensure the material is properly aligned and the rollers are clean. Adjust material width settings in the software if applicable.
  • Communication Errors: Verify the USB, TCP, or Wi-Fi connection between the machine and the computer. Restart both the machine and the computer. Ensure correct drivers are installed.
  • Registration Mark Errors: Ensure registration marks are clearly printed and not obscured. Check lighting conditions around the machine's camera.

7. User Tips

  • Test Cuts: Always perform a small test cut on a scrap piece of your material before running a full job to verify settings.
  • Material Compatibility: While the machine boasts 'no material limitation' for identification, always ensure the material weight (up to 350g/㎡) and type are suitable for cutting to prevent damage to the blade or machine.
  • Optimize Layout: Arrange your designs efficiently in the software to minimize material waste and maximize output per sheet.
  • Backup Files: Regularly back up your cutting designs and software settings.

8. Warranty and Support

For warranty information, technical support, or service inquiries, please contact your original point of purchase or the manufacturer directly. Refer to the documentation provided with your purchase for specific warranty terms and contact details.

Certificate of Machinery Directive (UDEM)

Figure 6: Certificate of Machinery Directive

Alibaba.com Gold Plus Supplier Verification Report

Figure 7: Alibaba.com Gold Plus Supplier Verification Report

© 2024 Jinka. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.