HITBOX MT2000II

Contents
HITBOX MT2000II Welder in use

HITBOX MT2000II Multi-Process Welding Machine User Manual

Model: MT-2000II

1. Introduction

Thank you for purchasing your HITBOX inverter welder. This manual provides essential information for the proper operation and maintenance of your MT2000II welding machine. Please read it carefully before use and keep it for future reference.

The HITBOX MT2000II is designed with high-quality components and undergoes rigorous lab testing to ensure superior welding performance and reliability. Your safety and satisfaction are our top priorities. For any questions or concerns, please contact HITBOX support.

2. Safety Precautions

WARNING: Welding can be dangerous. Always follow safety guidelines to prevent injury or damage.

  • Electric Shock Hazard: Never touch electrical parts. Ensure the welder is properly grounded. Disconnect power before assembly or maintenance. Do not use the welder with the case open. Always wear good insulating gloves.
  • Arc, Spatter, and Slag Hazards: These can cause eye and skin burns, and abnormal noise can damage hearing. Always use a welding mask to protect your face and eyes, wear appropriate welding clothes to protect your body, and use hearing protection when operating in noisy environments.
  • Working Environment: Using the welder in narrow or elevated places increases the risk of electric shocks, falls, and other accidents. Use a VRD (Voltage Reduction Device) or a welder with built-in VRD in such locations. Check the VRD device according to safety rules.
  • Fumes and Gases Hazard: Welding fumes and gases are harmful to health. Use local exhaust ventilation and respiratory protective equipment. Ensure adequate ventilation in narrow spaces. Do not use the welder in degreasing, cleaning, or spraying areas.
  • Fire and Explosion Hazard: Welding can cause fire or explosions. Do not place combustible or flammable materials near the welding area. Do not weld airtight containers (e.g., oil tanks, tubes). Always have fire apparatus available.
  • Lifting Device: If using a lifting device, ensure all accessories are removed. Never lift the welder over people. Do not use rollers to move the welder as this may cause damage.

3. Product Description

The HITBOX MT2000II is a 4-in-1 multi-process inverter welding machine, featuring advanced IGBT technology for stable and superior welding performance. It supports MMA, Gas MIG, Gasless MIG, and Lift TIG welding processes.

Key Features:

  • 4-in-1 Multi-Process: Capable of MMA, Gas MIG, Gasless MIG, and Lift TIG welding.
  • Synergic Control: Automatically matches wire feed speed and voltage for MIG welding, making it beginner-friendly.
  • Advanced IGBT Inverter Technology: Ensures stable and consistent welding with features like Hot Start, Arc Force, and Anti-stick.
  • Revolutionary LED Display: Large, clear digital display for accurate data reading, even with a welding helmet.
  • Compact & Portable: Lightweight design with a handle for easy transport, ideal for outdoor maintenance, farm equipment, road equipment, and DIY projects.
  • Safety Protections: Includes overvoltage, overcurrent, overheating, and overload protection.
  • Wire Feeding System: Consistent wire feeding for 2 lbs (.030" & .039") welding wire.

Applications:

The MT2000II is suitable for welding various metal materials such as carbon steel, alloy steel, and nonferrous metals. It is ideal for manufacturing metal parts, industrial power stations, aerospace, automotive, and general construction.

Four welding modes: Gas MIG, Gasless MIG, MMA, and Lift TIG

Image: The MT2000II supports Gas MIG, Gasless MIG, MMA, and Lift TIG welding modes.

4. Specifications

Table 1: Technical Parameters for MT2000II
ParameterValue
Brand NameHITBOX
Model NumberMT2000II
Inverter TechnologyIGBT
Input VoltageAC220V±15%
Frequency50/60HZ
Max OCV60V
Duty Cycle40%
Power Factor0.73
Postflow Time1.0±0.5s
Wire Diameter0.8/1.0mm
Rods Diameter (MMA)2.5/3.2mm
Wire Feed Speed3-18m/min
Applicable Thickness (MIG)1.5-10mm
Applicable Thickness (ARC)2-12mm
Applicable Thickness (LIFT TIG)1-8mm
Dimensions42x29x35cm
Weight9.8kg
CertificationCE

5. Package Contents

The MT2000II welding machine package includes the following items:

Diagram showing all included accessories: MIG Gun, Ground Clamp, Electrode Holder, Gas Hose, Flux Cored Wire, Conductive Tips, Rollers, Hammer, Hose Clamps, User Manual.

Image: Package contents diagram.

  1. 15AK MIG Gun 10 ft
  2. Ground Clamp 4.9 ft
  3. Electrode Holder 4.9 ft
  4. Gas Hose 4.9 ft
  5. .030 Flux Cored Wire 2 lbs
  6. Conductive Tips (.030*2, .039*2)
  7. Rollers (V: .030/.039)
  8. Hammer
  9. Hose Clamp*2
  10. User Manual

6. Setup Instructions

6.1 Power Connection

Ensure the power switch on the back of the machine is in the OFF position before connecting to power.

Video: Demonstrates plugging in the power supply and turning on the welder.

  1. Plug the power cord into a suitable power outlet (AC220V±15%).
  2. Ensure the power supply matches the welder's input voltage.
  3. Flip the power switch on the back of the machine to the ON position.

6.2 Ground Clamp Connection

Connect the ground clamp to the positive (+) socket on the front panel of the welder.

Connecting the ground clamp to the positive socket

Image: Connecting the ground clamp to the positive (+) socket.

6.3 Torch Connector Plug

Connect the torch connector plug to the negative (-) socket on the front panel of the welder.

Connecting the torch connector plug to the negative socket

Image: Connecting the torch connector plug to the negative (-) socket.

6.4 MIG Gun/Torch Connection

Insert the MIG gun/torch into its designated port on the front panel and secure it.

Connecting the MIG gun/torch to the welder

Image: Connecting the MIG gun/torch.

6.5 Wire Feeder Setup

The wire spool should be mounted on the frame shaft of the wire feeder. Ensure the wire plate's hole position aligns with the fixing bolt on the frame shaft.

Internal view of the wire feeding mechanism with wire spool

Image: Internal view of the wire feeding mechanism with wire spool.

  1. Depending on the wire diameter, choose the appropriate wire feed slot.
  2. Loosen the nut of the pressure roller, feed the welding wire into the wire feeder groove through the wire guide tube.
  3. Adjust the pressure wire to press the welding wire to ensure it does not slide, but avoid excessive pressure to prevent wire deformation.
  4. Rotate the wire spool clockwise to release the wire. To prevent loosening, place the new wire disk head in the fixing hole on the side of the wire disk.

6.6 Gas Connection (for Gas MIG)

For Gas MIG welding, connect the gas cylinder (with CO2 or mixed gas) equipped with a pressure reducing flow meter to the gas inlet at the back of the machine.

7. Operating Instructions

7.1 Control Panel Overview

Diagram of the MT2000II control panel with labeled components

Image: Control panel layout with labeled components.

  1. Euro welding torch connector
  2. Gas/gasless shielded ARC Crossover sub
  3. Shutters
  4. Positive output terminal
  5. Current/Feeding speed adjustment knob
  6. LED digital display
  7. Voltage adjustment knob
  8. Function switch button

7.2 Mode Selection

The MT2000II supports multiple welding modes. Use the 'Multi-function' button (Function switch button) to cycle through the available modes.

Digital display showing mode selection for CO2/0.8, MIX/0.8, FLUX/0.8, FLUX/1.0, MMA, Lift TIG

Image: Digital display showing various welding modes and wire sizes.

  1. Press the 'Multi-function' button to select the desired welding mode (MMA, CO2/0.8, MIX/0.8, FLUX/0.8, FLUX/1.0, LIFT TIG). The corresponding indicator will light up.
  2. For MIG modes (CO2, MIX, FLUX), you can also select the wire size (0.8mm or 1.0mm).

7.3 Parameter Adjustment

After selecting the welding mode, adjust the parameters using the 'Welding Voltage' and 'Wire Speed' knobs.

  1. Welding Voltage Knob: Adjusts the welding voltage. The set value is displayed on the voltmeter.
  2. Wire Speed Knob: Adjusts the wire feed speed.
  3. Synergic Control (MIG Mode): In MIG mode, the machine can automatically match welding parameters. You can fine-tune the welding voltage. Press the 'Selection' button to restore default matching values.
  4. Manual Adjustment (Non-Synergic): If the synergic unified status indicator is off, you can manually adjust welding voltage, current, and arc force.
  5. MMA Mode: Adjust current (22-200A) using the 'Welding Voltage' knob.
  6. Lift TIG Mode: Adjust current using the 'Welding Voltage' knob.

7.4 Welding Parameters Recommendation

Refer to the table below for recommended welding parameters under standard conditions. These values serve as a general guide and may need adjustment based on specific materials and conditions.

Table 2: Recommended Welding Parameters (Excerpt)
Thickness (mm)Wire Diameter (mm)Current (A)Voltage (V)Speed (cm/min)Gas Flow (L/min)
1.00.8,0.970~8017~1850~6010~15
2.01.0,1.2115~12519~2050~6010~15
3.21.0,1.2150~17021~2245~5015~20
4.51.0,1.2140~20022~2445~5015~20

8. Maintenance

Regular maintenance ensures the longevity and optimal performance of your welding machine.

  1. Dust Treatment: Regularly (at least once a month in smoky or contaminated environments) clean the machine with dry, clean compressed air.
  2. Compressed Air Pressure: Ensure compressed air is at the required pressure to avoid damaging welding machine components.
  3. Electrical Connections: Check internal electrical connections, especially connectors, for good contact. If loose, tighten them. If there is oxidation, use sandpaper to remove the oxide film before reconnecting.
  4. Moisture Prevention: Avoid water or moisture in the welder. If exposed, dry it immediately. Measure insulation with a Megohm meter (between connection nodes and casing) before resuming operation.
  5. Storage: If the welder will not be used for a long time, store it in its original packaging in a dry environment.

Note: All maintenance work must be performed with the power completely disconnected and the power plug unplugged.

9. Troubleshooting

If you encounter issues with your welding machine, refer to the following common problems and their remedies before contacting support.

9.1 No Power / No Output

MalfunctionPossible CauseRemedy
Digital display meter light off, fan doesn't run, no outputPower switch closed, power supply issue, rectifier bridge damaged, auxiliary power malfunction.Confirm power switch is ON, check power supply, contact dealer if internal components are damaged.
Digital display meter light on, fan runs, no outputPoor contact in patch cords/output connection, broken welding torch control line/micro switch, damaged control circuit.Check and secure connections, inspect welding torch, contact dealer for circuit damage.

9.2 Abnormal Display / Unstable Current

MalfunctionPossible CauseRemedy
Digital display abnormalOvercurrent/overheat protection, inverter circuit fault, damaged rectifier diode.Restart after overcurrent indicator off, allow cooling for overheat, contact dealer for circuit issues.
Current cannot be stabilizedGrid voltage changes, serious interference from grid/electrical equipment.Ensure stable power supply, minimize electrical interference.

9.3 No Gas Output (for Gas MIG)

MalfunctionPossible CauseRemedy
No gas outputNo gas in meter, solenoid valve no voltage, damaged solenoid valve, wire feeder circuit fault.Check gas supply, solenoid valve, and wire feeder circuit.

9.4 Wire Feeder Issues

MalfunctionPossible CauseRemedy
Unstable wire feeding / arcIncorrect pressing handle pressure, accumulated powder/scrap in wire-guide tube/reel, mismatched wire/reel diameter, misaligned wire-guide tube.Adjust handle pressure, clean components, ensure correct wire/reel match and alignment.

10. User Tips

  • Aluminum Welding: For welding aluminum, it is generally recommended to use a MIG welder with pure argon gas and a spool gun. Ensure your wire and gas settings are appropriate for aluminum.
  • Beginner-Friendly: Utilize the synergic control feature in MIG mode to automatically set optimal parameters, simplifying the learning curve.
  • TIG Torch: Note that the WP-17V TIG Torch is typically not included and needs to be purchased separately for Lift TIG welding.

11. Support

If you encounter any problems or have questions regarding your HITBOX MT2000II welding machine, please feel free to contact HITBOX customer service. Our team is available to assist you with any technical issues or operational queries.

You can find contact information on the official HITBOX website or through your purchase platform.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.