1. Important Safety Notes
- The HW-602 and HW-603 models are unpowered filters and cannot be used alone. They do not include water pumps, water pipes, or import/export pipes. An external pump and hoses are required for operation.
- For HW-602B and HW-603B models, the maximum lift of the integrated pump is 0.85 meters. Ensure your aquarium setup is compatible with this lift.
- Always disconnect power before performing any maintenance or cleaning.
- Ensure all connections are secure to prevent leaks.
- This filter is designed for both fresh water and sea water use.
2. Product Overview and Components
The Sunsun external aquarium filter is designed for efficient and quiet filtration. Depending on the model, it may include an integrated pump and all necessary hoses, or it may function as a prefilter requiring external components.

Figure 2.1: Main components of the Sunsun aquarium filter, including the filter bucket, sponges, hoses, and pump (if included).
2.1 Key Components

Figure 2.2: Exploded view of the filter components.
- Shell
- Pump (for B models)
- Regulating valve
- Upper treatment board
- Filter sponge
- Lower treatment board
- Inlet pipe
- Universal outlet pipe
- Perforated outlet pipe
- Rubber tubes
3. Setup Instructions
3.1 Filter Media Installation
The filter bucket is designed for physical filtration using three layers of filter cotton. These sponges are crucial for mechanical and biological filtration.

Figure 3.1: Filter media layers (hydrophobic, medium, secret filter cotton) and filtering plates.
- Place the filtering plate at the bottom of the filter bucket.
- Layer the filter sponges (typically black, yellow, blue) onto the filtering plate.
- Place the upper treatment board on top of the sponges.
- Ensure the O-ring is properly seated in the lid for a watertight seal.

Figure 3.2: The O-ring ensures a secure, leak-proof seal for the filter bucket.
3.2 Hose and Pipe Connection
Connect the inlet and outlet pipes to the filter unit and position them in your aquarium according to the desired flow. The HW-602B and HW-603B models come with a pump and hoses, while HW-602 and HW-603 require these to be supplied externally.

Figure 3.3: Available outlet pipe options and the inlet pipe design.
- Attach the inlet pipe (7) and outlet pipe (8 or 9) to the filter head.
- Secure the rubber tubes (10) to the pipes and route them into your aquarium.
- For models HW-602B/HW-603B, connect the integrated pump (2) to the inlet.
- For models HW-602/HW-603, connect your external water pump to the inlet pipe.

Figure 3.4: Schematic diagrams illustrating two common setup modes for the filter. Mode 1 shows a setup with an external water pump, while Mode 2 shows a prefilter setup.
Mode 1: External Water Pump Setup
- Water flows from the aquarium (IN) to an external water pump.
- The pump pushes water into the filter bucket.
- Filtered water returns to the aquarium (OUT).
Mode 2: Prefilter Setup
- Water flows from the aquarium (IN) into the prefilter bucket.
- The prefilter then feeds into a main external filter (not shown in detail).
- Filtered water returns to the aquarium (OUT) from the main filter.
4. Operating Instructions
4.1 Initial Start-up
- Ensure all connections are tight and the filter bucket lid is securely fastened.
- Fill the filter bucket with water to prime it (if not self-priming).
- Plug in the pump (for HW-602B/HW-603B) or your external pump (for HW-602/HW-603).
- Check for any leaks immediately after starting.
4.2 Flow Regulation
The filter unit includes a regulating valve (3) to adjust the water flow rate. This allows you to customize the flow based on your aquarium's needs and the type of fish or plants you have.

Figure 4.1: The switch allows you to regulate water traffic (flow) through the filter.
- Turn the switch to the 'Open' position for maximum flow.
- Turn the switch towards 'Close' to reduce the flow.
4.3 Quiet Operation
Sunsun filters are designed for ultra-quiet operation, minimizing disturbance to your aquatic environment and household.
5. Maintenance
Regular maintenance is essential for optimal filter performance and water quality.
5.1 Filter Sponge Cleaning and Replacement
The filter sponges are the primary mechanical and biological filtration media. They should be cleaned or replaced periodically.

Figure 5.1: A set of three filter sponges (blue, yellow, black) for models 602/602B.
- Disconnect the filter from power.
- Close the regulating valve and disconnect the hoses.
- Open the filter bucket lid and remove the filter sponges.
- Rinse the sponges in old aquarium water to preserve beneficial bacteria, or replace them if heavily soiled or degraded.
- Customers can also replace the filter material with other biological filter media to suit specific aquarium needs.
- Reassemble the filter, ensuring the O-ring is correctly seated and the lid is securely closed.
5.2 Pump Maintenance (for HW-602B/HW-603B)
Periodically inspect the pump impeller for debris and clean as necessary to maintain flow rate.
6. Troubleshooting
6.1 Reduced Flow Rate
- Check if filter sponges are clogged and require cleaning.
- Ensure the regulating valve is fully open.
- Inspect hoses for kinks or blockages.
- For HW-602B/HW-603B, check the pump impeller for debris.
6.2 Leaks
- Ensure the O-ring on the filter lid is clean, undamaged, and properly seated.
- Verify all hose connections are tight and secure.
- Check for cracks in the filter shell or pipes.
6.3 Excessive Noise
- Ensure the filter is placed on a stable, level surface.
- Check for air trapped inside the filter; gently tilt the filter to release air bubbles.
- For HW-602B/HW-603B, inspect the pump impeller for foreign objects or wear.
7. Specifications
| Feature | HW-602 / HW-602B | HW-603 / HW-603B |
|---|---|---|
| Type | External Aquarium Filter / Prefilter | |
| Power (W) | 6W (for B models with pump) | |
| Voltage | 110-120V / 220-240V (model dependent) | |
| Max Flow | 400 L/H (for B models with pump) | |
| Max Lift | 0.85 m (for B models with pump) | |
| Hose Diameter | 16 mm | |
| Cable Length | 1.4 m (for B models with pump) | |
| Dimensions (L x W x H) | 140 x 140 x 255 mm (HW-602B) Diameter 16cm, Height 29cm (HW-602) | 165 x 165 x 295 mm (HW-603B) Diameter 19cm, Height 32cm (HW-603) |
| Filter Barrel Material | ABS | |
| Origin | Mainland China | |
| Package Dimensions | 20 cm (Length) x 30 cm (Width) x 20 cm (Height) | |
| Package Weight | 0.9 kg | |

Figure 7.1: Detailed specifications for model 602B.

Figure 7.2: Detailed specifications for model 603B.

Figure 7.3: Size comparison between HW-602 and HW-603 models.

Figure 7.4: Size comparison between HW-602B and HW-603B models.
8. User Tips
- Pre-rinse Filter Media: Always rinse new filter sponges thoroughly with clean water before placing them in the filter to remove any manufacturing dust.
- Aquarium Water for Cleaning: When cleaning filter sponges, use water from your aquarium (during a water change) instead of tap water. This helps preserve the beneficial bacteria colony essential for biological filtration.
- Regular Checks: Periodically check hose connections and the O-ring for signs of wear or damage to prevent leaks.
- Proper Placement: Ensure the filter is placed below the water level of the aquarium for optimal performance, especially for models requiring external pumps.
9. Warranty and Support
9.1 Returns and Refunds
- Free Returns: Enjoy free returns within 90 days of purchase.
- Fast Delivery & Refunds for Issues:
- Receive a $1.00 coupon code if delivery is delayed.
- Full refund if the package is lost.
- Full refund if items are damaged upon arrival.
- Full refund if no delivery within 30 days.
9.2 Security & Privacy
Your personal details are protected and not shared with third parties without your consent. All payments are secure.
9.3 Contact Information
For further assistance or inquiries, please use the following contact details:

Figure 9.1: Contact details for customer support.
- Telephone: +86-13980494342
- E-mail: 2165590580@qq.com
- WeChat: LW494342
- QQ: 2165590580