DOOGEE BoneBeat Run Ray Bone Conduction Headphones User Manual

1. Introduction

Welcome to the user manual for your DOOGEE BoneBeat Run Ray Bone Conduction Headphones. These headphones are designed for outdoor sports, featuring bone conduction technology, IP66 waterproofing, dynamic sport lights for safety, and Bluetooth 6.0 for stable connectivity. This manual provides detailed instructions on how to set up, operate, and maintain your headphones.

2. What's in the Box

Please check the package contents upon unboxing:

• 1 x BoneBeat Run Ray Headphones
• 1 x Elastic Strap
• 1 x Storage Pouch
• 1 x Type-C Charging Cable
• 1 x Packing Box
• 1 x User Manual
• 1 x Warranty Card

3. Product Diagram

Familiarize yourself with the components and controls of your BoneBeat Run Ray headphones:

• Multi-Function Button (MFB): Power On/Off, Play/Pause, Answer/End Call, Reject Call, Voice Assistant, EQ Mode Switch.
• Volume + Button: Increase Volume, Next Song, Mute Call.
• Volume - Button: Decrease Volume, Previous Song.
• LED Indicator: Shows power status, pairing mode, and charging status.
• Dynamic Sport Light: Integrated light strip for visibility.

4. Setup and Pairing

4.1 Power On/Off

• To Power On: Press and hold the Multi-Function Button for 2 seconds until the LED indicator flashes blue and you hear "Power On".
• To Power Off: Press and hold the Multi-Function Button for 5 seconds until the LED indicator flashes red and you hear "Power Off".

4.2 Bluetooth Pairing

First Use Pairing:

1. Power on the headphones. They will automatically enter pairing mode, with red and blue lights flashing alternately, and you will hear "Pairing".
2. Open your device's Bluetooth settings and select "Doogee BoneBeat Run Ray". You will hear "Connected" once paired.

Forced Pairing:

1. Ensure your headphones are powered off.
2. Press and hold the Multi-Function Button for 5 seconds until the LED indicator flashes red and blue alternately, and you hear "Pairing".
3. Open your device's Bluetooth settings and select "Doogee BoneBeat Run Ray". You will hear "Connected" once paired.

4.3 Multipoint Connection

The headphones support connecting to two Bluetooth devices simultaneously.

1. With the headphones powered off, press and hold the Multi-Function Button for 5 seconds until the red and blue lights flash alternately, and you hear "Pairing".
2. Open the Bluetooth menu on your first device and select "Doogee BoneBeat Run Ray". Pairing is complete when the first device shows "Pairing successful".
3. Turn off the Bluetooth function on the first device. The headphones will automatically re-enter pairing mode (red and blue lights flashing alternately).
4. Open the Bluetooth pairing list on the second device and select "Doogee BoneBeat Run Ray" to connect. The second device will complete pairing.
5. Turn on the Bluetooth function on the first device and manually tap "Doogee BoneBeat Run Ray" to reconnect. The headphones are now connected to both devices.

4.4 Restore Factory Settings

In power-off mode, press and hold the Multi-Function Button for 10 seconds. The headphones will reset successfully and then power off.

5. Operation

5.1 How to Wear

Pick up the headphones, bring them behind the back of your neck, and position the ear hooks on your ears. The transducers should rest in front of your ears for optimal bone conduction audio. Incorrect wearing may cause discomfort.

5.2 Music, Call, and Volume Controls

5.3 Lighting Effect Mode Switching

The BoneBeat Run Ray features a dynamic sport light for enhanced visibility. When music is playing, triple-press the Multi-Function Button to cycle through the following lighting modes:

• Always On
• Slow Breathing Flash
• Fast Flash
• Off

5.4 EQ Modes

The headphones offer two EQ modes:

• Standard Mode: Provides balanced frequency for general music listening.
• Vocal Booster Mode: Enhances intermediate frequencies, ideal for audiobooks, podcasts, and vocal-centric content.

How to Switch EQ Modes: Double-click the Multi-Function Button while music is playing. You will hear a prompt tone indicating "Standard Mode" or "Vocal Booster Mode".

6. Care and Maintenance

6.1 Charging Tips

• During charging, the LED indicator will turn red, and the headphones will automatically power off.
• The LED indicator will turn blue when charging is complete.
• The charging port is Type-C.
• Fast charging provides 2 hours of music playback with just 10 minutes of charging.

6.2 Precautions

• Store the headphones in a cool, dry place. Operating temperature range is 0°C to 40°C (32°F to 102°F).
• Keep the headphones away from heat sources, flammable gases, or corrosive liquids. Avoid prolonged direct sunlight or placement in hot environments.
• If any part of the product is damaged, smokes, heats up, or emits a burning smell, discontinue use immediately.
• The headphones have an IP66 dust and splash resistance rating, suitable for non-water sports and exercises. They are not fully waterproof; do not immerse them in water. The IP66 rating is not permanent and may decrease with normal wear and tear.
• Clean the headphones with a soft, dry cloth.
• After long storage, charge the headphones before use.
• If not used for a long period, charge them at least once every 3 months to extend battery life.
• Always ensure the charging port is dry before connecting the charging cable. Moisture in the port can lead to short circuits, fire, or explosions.
• Do not charge immediately after exercising, as sweat inside the charging port could cause circuit damage.

6.3 Adjustable Headband

The adjustable headband is designed for users with smaller head circumferences. Before wearing, install the rear adjustment strap as shown in the diagram and adjust it for a comfortable fit.

7. Specifications

Here are the detailed technical specifications for the DOOGEE BoneBeat Run Ray headphones:

8. Troubleshooting

If you encounter any issues with your headphones, please refer to the following common solutions:

• No Power: Ensure the headphones are fully charged. Press and hold the MFB for 2 seconds to power on.
• Cannot Pair: Make sure the headphones are in pairing mode (red and blue lights flashing alternately). Turn off and on Bluetooth on your device, then try pairing again. If necessary, perform a factory reset.
• No Sound: Check the volume level on both the headphones and your connected device. Ensure the headphones are properly connected via Bluetooth.
• Poor Sound Quality: Ensure the headphones are worn correctly, with transducers in front of your ears. Try switching EQ modes. Check for interference from other devices.
• Intermittent Connection: Ensure you are within the 10-meter Bluetooth range. Avoid physical barriers between the headphones and your device.
• Charging Issue: Verify the Type-C cable is securely connected and the charging port is dry and clean. Use a 5V/180mA power input.

9. User Tips

• For optimal sound and comfort, ensure the bone conduction transducers are positioned correctly in front of your ears, not covering them.
• Utilize the dynamic sport light during evening or low-light activities to enhance your visibility and safety.
• Experiment with both Standard and Vocal Booster EQ modes to find the best audio experience for different types of content (music, podcasts, calls).
• Regularly clean the charging port and ensure it's dry before charging to prevent potential damage.

10. Warranty and Support

Your DOOGEE BoneBeat Run Ray headphones come with a warranty card included in the package. Please refer to the warranty card for details on coverage and terms.

For further information, support, or to view the full user manual in PDF format, you can access the official user guide PDF: DOOGEE BoneBeat Run Ray User Manual (PDF).

11. Regulatory Information

11.1 FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

FCC Radiation Exposure Statement: The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

11.2 EC Declaration

This product complies with the below listed UK Directives:

• Radio Equipment Regulations 2017
• The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012
• The Batteries and Accumulators (Placing on the Market) Regulations 2008 (as amended) and the Waste Batteries and Accumulators Regulations 2009 (as amended).

FCC ID: 2AX4YBC02

MADE IN CHINA

For more function information, scan the QR code provided in the original user manual.