LASER TREE K1Max Plus

Contents

LASER TREE K1Max Plus Laser Engraver User Manual

Model: K1Max Plus with Adjustable 20W, 40W, 60W Laser Module

1. Safety Statement

Before using the laser engraving machine, please peruse this safety manual attentively to comprehend the operating protocols and potential hazards associated with the laser engraving machine.

  1. Sharp edges may cut your hands when assembling the stand, gloves are recommended.
  2. Laser beam has high energy and heat; direct contact with eyes or skin may cause serious injury. When the laser is working, always pay attention to the position and direction of laser beam movement.
  3. Children or teenagers are strictly prohibited from using the laser engraving machine alone.
  4. The laser engraver should be placed on a stable tabletop. Before use, please clean the work area to ensure that the surrounding environment is safe and free of debris, flammable and explosive items, etc. to prevent potential safety hazards.
  5. Before using the laser, carefully check the power connection of the laser engraver. Make sure that the power cord is intact and the plug is firmly connected to avoid accidents caused by power problems.
  6. When the laser is working, you must wear professional protective glasses to protect your eyes from laser damage. Protective glasses can block the laser light and avoid direct exposure to the eyes.
  7. When the laser is working, the engraving area should be paved with metal or non-combustible mats to prevent the laser from burning the workbench or causing fire and other safety hazards.
  8. When the laser is working, please do not leave the equipment during operation. Stay focused and pay close attention to the operation of your equipment, to prevent the engraving or cutting material from catching fire.
  9. When the laser is working, some materials produce smoke during laser cutting. Please keep the room well ventilated.
  10. Residue and debris can accumulate during the cutting and engraving process. Please clean up the work area promptly.
  11. Please ensure that a fire extinguisher is located near the laser engraving machine and that regular maintenance and inspections are conducted to promptly respond to any accidents that may occur.

2. Specifications

The LASER TREE K1Max Plus is a versatile laser engraving and cutting machine designed for both hobbyists and professionals. Below are its key specifications:

FeatureSpecificationFeatureSpecification
BrandLASERTREESupport SoftwareLightBurn & LaserGRBL
ModelK1 MAX PLUS (LT-K1-MAX-PLUS-60W)Air AssistanceYes
Engraving Area1000*1500 mmRotation Axis OutputYes
Engraving Speed20000 mm/min (Max)Offline EngravingYes
Wavelength450nm (±10nm)Emergency StopYes
Focus length40mmTilt ProtectionYes
Optical Power60W+ (Adjustable 20W/40W/60W)Status IndicatorYes
InputDC24V 10AOperating Temperature0-40°C
CertificationsCE, FCC, RoHS, WEEEConditionNew

Laser Module Spot Sizes:

  • 20W: 0.15*0.15mm
  • 40W: 0.15*0.18mm
  • 60W: 0.15*0.25mm

3. Product Overview

3.1 Laser Engraving Machine Components

The K1Max Plus laser engraving machine features a large working area and a modular design for ease of use and maintenance.

LASER TREE K1 Max Plus 60W Laser Engraver with 1000x1500mm working area
LASER TREE K1 Max Plus 60W Laser Engraver with 1000x1500mm working area.
Diagram showing the 1000x1500mm working area of the laser engraver
The expansive 1000x1500mm working area supports one-pass engraving and cutting of large materials, enhancing efficiency and creative flexibility.
Diagram illustrating the detachable X and Y axes design for quick assembly
The X and Y axes feature a modular, splicable design for fast and easy installation.
Images showing quick assembly and neat cable organization with drag chains
The X and Y axes utilize drag chains for organized and protected cabling, reducing wear and ensuring smooth operation.

3.2 Laser Module

The K1Max Plus comes with an adjustable 20W, 40W, or 60W laser module, offering incredible cutting and engraving capabilities.

Image demonstrating 60W optical power output cutting through 20mm plywood, 30mm black acrylic, and 40mm pine wood
The 60W+ optical power output provides incredible cutting capability, handling materials like 20mm plywood, 30mm black acrylic, and 40mm pine wood in a single pass.
Diagram showing switchable power modes for the laser module: 20W, 40W, 60W
The laser module features three switchable power modes (20W, 40W, 60W) for versatile operation.

Laser Module Components:

  1. Power indicator: Red when power supply is connected.
  2. Signal indicator: Green when signal is received.
  3. Working temperature display: Shows real-time working temperature. An alarm sounds if temperature exceeds 55°C. Keep temperature below 55°C and environmental temperature below 35°C for optimal performance.
  4. Laser view window: Allows observation of the laser.
  5. Fixed focus lever: Used for adjusting focus.
  6. Input port: Power input.
  7. Air assistance port: For connecting air assist.
  8. Optical power indicator: Indicates the current optical power.
  9. Switch: Single press to turn off over-temperature alarm. Long press (5S) to enter power switching mode (60W > 20W > 40W). Continuous short press switches optical power.
  10. Red cross line locating: For precise positioning.
  11. Laser output aperture: Where the laser beam exits.

4. Setup Guide

4.1 Packing List

Ensure all components are present before beginning assembly. Gloves are recommended due to sharp edges.

Image showing the main components of the K1 Max Plus laser engraver, including X-axis, Y-axis, frames, linear guide rails, coupling shafts, drag chain guides, transmission unit, motor mounting plates, pulley mounting plate, drag chain fixing plate, support feet, and control boxes.
Main components of the K1 Max Plus laser engraver.

Main Components:

  • X-Axis A x1, X-Axis B x1
  • Y-Axis A x2, Y-Axis B x2
  • Front Frame x2, Rear Frame x2
  • Linear Guide Rail A x1, Linear Guide Rail B x1
  • Coupling Shaft A x1, Coupling Shaft B x1
  • X-axis Drag Chain Guide x2, Y-axis Drag Chain Guide x2
  • X-axis Transmission Unit x1
  • X-axis Motor Mounting Plate x1, Y-axis Motor Mounting Plate x1
  • Y-axis Pulley Mounting Plate x1
  • Y-axis Drag Chain Fixing Plate x1
  • Y-Axis Drag Chain Carrier Link Plate x1
  • Y-axis Drag Chain Support Foot x2
  • X-axis Cable x1, Y-axis Cable x1
  • Distribution Box x1, Main Control Box x1
  • Support Foot x3
Image showing accessories including power adapter, AC cable, USB cable, 60W laser module, air pump, protective glasses, and material pack.
Included accessories: Power Adapter, AC Cable, USB Cable, 60W Laser Module, Air Pump, Protective Glasses, Material Pack.

Splicing Kit:

  • Linear Splicing Connector A x10
  • Linear Splicing Connector B x10
  • Flat Screw M5*16 x41

Tool Kit:

  • Cleaning Brush x1
  • 8-10 Open Spanner x1
  • 4.5 Open Spanner x1
  • L-Allen wrench x1
  • Cable Ties x3
  • Timing Belt x2
  • Sleeve Coupling x1
  • TF Card x1, Card Reader x1
  • Spare Laser Protective Lens x2
  • Air Pump Filter Sponge x2

Screws and Fasteners:

  • Round Screw M4*18 x1 (Screw E)
  • Round Screw M5*10 x4 (Screw C)
  • Round Screw M5*16 x8 (Screw F)
  • Round Screw M5*20 x21 (Screw A)
  • Flat Screw M2.5*4 x2 (Screw B)
  • Flat Screw M3*6 x7 (Screw I)
  • Flat Screw M3*12 x20 (Screw H)
  • Flat Screw M5*20 x1 (Screw G)
  • Flat Screw M5*25 x1 (Screw G)
  • Thin Flat Screws M4*6 x28 (Screw D)
  • Limiting Column Sleeve 5*8*8 x1 (Screw G)
  • Limiting Column Sleeve 5*8*12 x1 (Screw G)
  • Fasten Screw M4*5 x5 (Screw G)
  • T-Nut x5 (Screw G)
  • Adjusting Screw M4*30 x2 (Screw G)
  • Hexagonal Copper Column M3*13+3 x3 (Screw J)

4.2 Assembly Instructions

4.2.1 Assembly of Main Frame

  1. Assemble the front/rear frames and X/Y-axis frames using linear splicing connectors.
Diagram showing the assembly of main frame components using linear splicing connectors and flat screws
Assembly of main frame components.

4.2.2 Assembly of X-axis

  1. Installation of Linear Guide Rail: Install linear guides A and B into the designated holes on the X-axis. Tighten the front and rear screws on the outermost side of each guide. Note: None of the screws should be fully tightened at this stage; they are only for temporary positioning.
  2. Adjust the Gap and Height: Focus on adjusting the gap and height at the junction between rails A and B. Ensure a smooth transition and consistent surface level without visible gap or misalignment. Once adjusted, securely tighten the two key screws in the center to lock the relative position.
  3. Test Sliding and Fixing: Manually slide the assembly to ensure smooth movement without binding. Fine-tune screws if binding occurs. Once smooth, tighten all fixing screws in sequence.
Diagram showing the assembly and adjustment of the X-axis linear guide rails
Assembly and adjustment of the X-axis linear guide rails.

4.2.3 Assembly of X-axis Transmission Unit

  1. Flatten the belt to avoid twisting. Insert the belt into the guide groove of the motor fixing plate, align the fixing plate with the left rear hole, and tighten the screws.
  2. Align the drive unit slider with the linear guide groove and secure.
  3. Align the mounting plate with the right rear hole of the X-axis and tighten the screws.
Diagram showing the assembly of the X-axis transmission unit, including belt installation and motor plate attachment
Assembly of the X-axis transmission unit.

4.2.4 Assembly of Y-axis Motor and Pulley Mounting Plates

  1. Secure the left Y-axis motor mounting plate with M5*10 screws.
  2. Install the sleeve coupling onto the connecting shaft and tighten it, then align and embed its flat end into the Y-axis motor mounting plate.
  3. Secure the right Y-axis pulley mounting plate with M5*10 screws and adjust the tension of the X-axis timing belt with M4*18 screws. Note: M4*18 screws are used to set the tension of the timing belt. Do not tighten the screw completely or the timing belt may be damaged.
Diagram showing the assembly of Y-axis motor and pulley mounting plates, including coupling shaft installation and belt tension adjustment
Assembly of Y-axis motor and pulley mounting plates.

4.2.5 Assembly of Engraving Machine Frame

  1. Push the X-axis into the Y-axis grooves on both sides. Use M5*20 screws to fix the front frame and rear frame.
Diagram showing how to push the X-axis into the Y-axis grooves and fix with M5*20 screws
Assembling the engraving machine frame.

4.2.6 Timing Belt Installation and T-Nut Insertion

  1. Make the timing belt face downward. Pass the timing belt through the X-axis pulley by hand or using an appropriate tool so that it fits snugly and ensures a smooth motion of the timing belt over the pulley. (Same operation for both left and right sides).
  2. Ensure a T-nut is inserted into the groove at each of the four corners of the Y-axis frame.
Diagram showing timing belt installation and T-nut insertion into the Y-axis frame
Timing belt installation and T-nut insertion.

4.2.7 Drag Chain Support Foot and Control Box Installation

  1. Fix the drag chain support foot to the left Y-axis support angle and the control box, and lock the support angle to the engraving machine frame.
Diagram showing the installation of the drag chain support foot and control box
Installation of drag chain support foot and control box.

4.2.8 Fastening Timing Belt Adjustment

  1. Fix the rear frame and timing belt: Use the M4x5 setscrew to secure the rear end of the timing belt to the rear frame.
  2. Position the X-axis: Push the X-axis backward to ensure that the X-axis is in close contact with the rear frame without any gap.
  3. Fix the front frame and timing belt: Pull the Y-axis timing belt forward to the correct tension and secure with the M4*5 set screws. Press the middle span of the timing pulley with your finger to make sure the belt is flexible. If the belt is too loose or too tight, it needs to be adjusted.
Diagram showing the steps to adjust and fasten the timing belt
Adjusting and fastening the timing belt.

4.2.9 Assembly of Distribution Box

  1. Use M3*13+3 hexagonal copper column to secure the junction box driver to the Y-axis motor pulley.
  2. Assemble the distribution box housing and the Y-axis drag chain fixing plate.
Diagram showing the assembly of the distribution box to the Y-axis motor pulley and drag chain fixing plate
Assembly of the distribution box.

4.2.10 Connecting Distribution Box Cables

  1. Connect the distribution box cables as shown in the diagram.
Diagram showing the connection of distribution box cables
Connecting distribution box cables.

4.2.11 Assembly of X-axis and Y-axis Drag Chain and Cable

  1. Install the Thin Flat Screws M4*6 in four locations, with each location requiring 3 screws.
Diagram showing the assembly of X-axis and Y-axis drag chains and cables
Assembly of X-axis and Y-axis drag chains and cables.

4.2.12 Connection Cable

  1. Connect the laser cable, main cable, electrostatic conductor cable, and air pump connection as illustrated.
Diagram showing the connection of various cables including laser cable, main cable, electrostatic conductor cable, and air pump
Connection of various cables.

4.3 Main Control Box Interface Description

Familiarize yourself with the main control box interfaces for proper operation.

Diagram of the main control box interface with numbered ports
Main Control Box Interface.
  1. Power input: Aviation 4P plug, DC 24V, 10A.
  2. Device main cable interface: PHB2.0-2*10PIN buckle terminal, connected to the distribution box.
  3. Air assistance output: DC5.5*2.1mm socket, output DC 24V.
  4. USB-PC interface: Port type USB-B, Connect with PC and burn program.
  5. Power switch: Self-locking switch, controls the current on and off of the whole machine, with red indicator light.
  6. TF card slot: Stores offline engraving files. Recommended TF card type is Class 10, 4~16G, Fat32 format. Supported offline engraving file format is .nc .gc.
  7. Emergency stop switch: Stops the device action and PWM signal output and disconnects the device from the PC.

4.4 Distribution Box Port Description

Diagram of the distribution box port interfaces
Distribution Box Port Interfaces.
  1. Rotary axis switching: Y-axis motor and rotary axis motor control switching.
  2. Y-axis motor output and limit signal input.
  3. X-axis motor output and limit signal input.
  4. Laser module output interface: MR30 port (DC 24V, GND, PWM).
  5. Device main cable interface: Connect to the main control box.
  6. Rotary axis output: PH2.0-4PIN terminal, connected to the rotary table motor.

5. Operating Instructions

5.1 Software Connection Guide

The K1 MAX PLUS supports LaserGRBL and LightBurn engraving software.

5.1.1 LaserGRBL

  1. Connect one end of the USB data cable to the engraving machine and the other end to the USB port of the computer with LaserGRBL software installed.
  2. Connect the power port of the engraving machine through the DC24V adapter and turn on the power switch.
  3. Open the LaserGRBL software on the computer, select the correct COM port and click connect. If the status bar displays "SimpleLaser 1.1h", the connection is successful.
Screenshot of LaserGRBL software interface showing connection steps
LaserGRBL software connection interface.

5.1.2 LightBurn

  1. Connect one end of the USB data cable to the engraving machine and the other end to the USB port of the computer with LightBurn software installed.
  2. Connect the power port of the engraving machine through the DC24V adapter and turn on the power switch.
  3. Open the LightBurn software, select “Start Your Free Trial” or “Activate License”.
  4. Create a new device, select "GRBL".
  5. Select USB connection.
  6. Set the engraving size to 1000*1500mm and modify the device name to "K1 MAX PLUS".
  7. Set the origin position of the machine and turn off automatic reset on power-on. (If you need to automatically reset every time you turn on the computer, please tick step 2 of the attached diagram.)
  8. Complete software setup.
  9. Select the "K1 MAX PLUS" device and the correct COM port. When the status bar displays Ready, the device is successfully connected.
Screenshots of LightBurn software setup process, including trial activation, device creation, USB connection, and work area settings
LightBurn software setup process.
Screenshots of LightBurn software showing device selection and successful connection status
LightBurn device selection and connection status.

5.2 Machine Test Guide

5.2.1 LaserGRBL Machine Test

  1. Engraving machine reset test: Find the reset button on the default interface of LaserGRBL and click it. Under correct operation, the laser module should move to the side of the control box and stop moving when it hits the limit column.
  2. Engraving machine movement test: Find the direction button on the default interface of LaserGRBL and set the moving distance and speed (recommended moving distance is 10mm). Click in any direction. Under correct operation, the laser module should move in the direction shown by the arrow.
  3. Engraving machine laser module light test: Find the light button on the LaserGRBL default interface and press and hold it. Under correct operation, the laser module should emit blue light normally.
Screenshots of LaserGRBL interface showing reset test, movement test controls, and laser light test button
LaserGRBL machine test procedures.

5.2.2 LightBurn Machine Test

  1. Engraving machine reset test: Find "Home" in the lower right corner of LightBurn default interface and click on it. Under correct operation, the laser module should move to the side of the control box and stop moving when it hits the limit column.
  2. Engraving machine movement test: Find "Move" in the lower right corner of LightBurn default interface and open it. Set the moving distance and speed (recommended moving distance is 50mm). Click in any direction. Under correct operation, the laser module should move in the direction indicated by the arrow.
  3. Engraving machine laser module light test: Open the device settings, turn on the laser ignition option and set air assist to M7. Find "Move" in the lower right corner of the LightBurn interface, set the optical power to 0.5% and click "Fire". Under correct operation, the laser module should emit blue light.
Screenshots of LightBurn interface showing reset test, movement test controls, and laser module light test settings
LightBurn machine test procedures.

5.3 Laser Module Focus Guide

The K1 MAX PLUS laser module has a working focal length of 40mm.

For Cutting:

When cutting, you only need to make the focus locate a bit lower than the surface of materials. For example, if you want to cut 12mm material, the focus should be 6mm lower than the material surface. Adjust the fixed focus lever to 6mm.

Diagram illustrating laser module focus adjustment for cutting, with a table of fixed focus lever usage reference for various material thicknesses
Laser module focus guide for cutting.

For Engraving:

When engraving, please ensure that the focus is located on the material surface. For example, if you want to perform engraving, just adjust the fixed focus lever to 0mm.

Diagram illustrating laser module focus adjustment for engraving, with a table of reference settings for engraving speed and power for different materials
Laser module focus guide for engraving.

5.4 Cutting Performance Tables

These tables provide detailed cutting depths for various materials at different power settings, demonstrating the efficiency and clean surfaces achieved with the 60W laser.

Detailed tables showing cutting depth for 5mm and 10mm plywood, pine wood, and MDF at 20W, 40W, and 60W power settings
Cutting performance for various materials and power settings.
Additional tables detailing one-pass cutting depth for 12mm plywood, 15mm pine wood, 5mm MDF, 15mm acrylic at 20W; 15mm plywood, 20mm pine wood, 9mm MDF, 20mm acrylic at 40W; and 20mm plywood, 40mm pine wood, 9mm MDF, 30mm acrylic at 60W
K60 Series one-pass cutting depth for various materials and power options.

6. Maintenance

6.1 Laser Module Lens Cleaning

When the laser module is used for a long time, you need to use an alcohol swab to wipe the laser protective lens to ensure the best cutting and engraving performance.

⚠️ Caution for lens cleaning:

  • Before wiping the lens, make sure the power is turned off and the laser module is disconnected from the engraving machine.
  • After wiping, allow the lenses to dry naturally for 3 to 5 minutes before use.

When the laser module is not used for a long time, please ensure that the lens is not polluted by dust.

Images showing dirty laser lenses (dust, fingerprint) and how to clean or replace the protective lens
Laser module lens cleaning and replacement.

Use an alcohol swab to clean or replace with a spare protective lens.

7. Troubleshooting

7.1 Common Issues

  • Machine not homing correctly or unexpected movement: Check if the limit switches are properly installed and connected. Ensure all cables are securely fastened. Refer to the "Machine Test Guide" in the operating section to verify homing and movement.
  • Laser not firing or weak output: Verify the power connection and ensure the laser module's working temperature is within the recommended range (below 55°C). Check the laser module light test in your software (LaserGRBL or LightBurn). Clean the laser protective lens if it's dirty.
  • Software connection issues: Ensure the correct COM port is selected in LaserGRBL or LightBurn. Check USB cable connection. Restart the software and the machine.
  • Poor engraving/cutting quality: Adjust the laser focus according to the material and operation (cutting or engraving). Ensure the material is flat and securely placed. Check the cutting/engraving parameters (speed, power, passes) against the reference tables.
  • Machine tilt alarm: The machine has tilt protection. If an alarm sounds, ensure the machine is on a stable, level surface.

8. User Tips

  • Homing/Limit Switches: The device is equipped with limit switches for homing. Ensure these are correctly installed and functioning for accurate positioning and safety. If the machine doesn't home correctly, check the physical connection of these switches.
  • Work Area Preparation: Always place a metal or non-combustible mat under your work area to protect your workbench from laser burns.
  • Ventilation: When cutting materials that produce smoke, ensure the room is well ventilated to maintain air quality.
  • Regular Cleaning: Promptly clean residue and debris from the work area after each use to prevent accumulation and maintain optimal performance.
  • Emergency Preparedness: Keep a fire extinguisher nearby and conduct regular checks.

9. Warranty and Support

All LASER TREE products come with a 1-year warranty from the store. For any inquiries or support needs, please contact us. All emails will be answered within 24 hours.

For more information about maintenance or technical support, please contact us at: lasertree@micost-optotech.com

You can also refer to the official user manual PDF for detailed instructions: View User Manual (PDF)

Video: Demonstration of the LASER TREE K1Max Plus laser engraver in action, showcasing its cutting capabilities.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.