CPVAN STC-X2

Contents

CPVAN Carbon Monoxide Detector

Model: STC-X2

Conforms to EN50291 Standard

1. Introduction

Thank you for choosing the CPVAN Carbon Monoxide (CO) Detector. This device is designed to protect you and your loved ones from the silent and deadly threat of carbon monoxide poisoning. Featuring a 10-year sensor lifespan and a clear real-time LCD display, this detector provides reliable and continuous monitoring. Its portable and easy-to-use design makes it suitable for various environments, including homes, RVs, motorhomes, and during camping trips.

2. Important Safety Information

WARNING: This carbon monoxide alarm is designed to detect carbon monoxide gas from ANY source of combustion. It is NOT designed to detect smoke or fire.

  • Never ignore any alarm. Investigate the cause and take appropriate action.
  • Do not paint the detector. Paint can clog the openings and interfere with the sensor's ability to detect CO.
  • Do not block the ventilation openings of the detector.
  • Test the alarm weekly to ensure proper operation.
  • Keep the detector clean by gently wiping it with a damp cloth. Do not use cleaning agents or solvents.

3. Package Contents

Please check the package for the following items:

  • CPVAN Carbon Monoxide Detector (Model: STC-X2)
  • 3 x AA Alkaline Batteries
  • Mounting Screws and Wall Plugs
  • User Manual (this document)

4. Setup and Installation

4.1 Battery Installation

  1. Locate the battery compartment on the back of the detector.
  2. Remove the plastic paper (insulation tab) from the 3 AA alkaline batteries.
  3. Insert the batteries correctly into the compartment, ensuring proper polarity (+/-).
  4. Close the battery compartment cover. The device will automatically turn on.
Back view of CPVAN CO detector showing battery compartment and mounting holes
Figure 1: Back view of the detector with battery compartment and mounting holes.

Video: Demonstration of CPVAN CO Detector features, including battery installation.

4.2 Placement Options

The CPVAN CO Detector offers versatile placement options:

  • Freestanding: Place the detector on any flat surface such as a desk, bookcase, or bedside table. This is ideal for mobile use in RVs, motorhomes, or camping tents.
    CPVAN CO detector on a bedside table
    Figure 2: Detector placed on a bedside table.
  • Wall Mounting: For permanent installation, use the included screws and wall plugs to mount the detector on a wall.

    Recommended Placement Areas:

    • In or near sleeping areas.
    • Near potential sources of CO, such as gas appliances, fireplaces, or attached garages.
    • At least 1.5 meters (5 feet) away from fuel-burning appliances to avoid false alarms.
    • At least 15 cm (6 inches) from the ceiling and any adjacent walls.

    Areas to Avoid:

    • Directly above heating or cooking appliances.
    • In areas with high humidity (e.g., bathrooms).
    • In direct sunlight or near air vents/fans.

5. Operating the Detector

5.1 Device Overview

Front view of CPVAN CO detector with LCD display, LED indicators, and Test button
Figure 3: Front panel of the CO Detector.

The detector features a clear LCD display, three-color LED indicators, and a 'TEST' button for intuitive operation.

5.2 LED Indicators and Display

The three-color LED indicators provide a quick visual status:

  • RED LED: Indicates an alarm condition (CO detected).
  • GREEN LED: Indicates normal operation (power supply).
  • YELLOW LED: Indicates a malfunction or low battery.

The LCD display shows the current CO concentration in parts per million (PPM). The display activates when CO levels exceed 25 PPM.

CO detector display showing 25 PPM and activating
Figure 4: Display turns on when CO concentration exceeds 25 PPM.
Real-time LCD display showing CO, Low Battery (Lb), and End of Service Life indicators
Figure 5: LCD display indicators for CO, Low Battery (Lb), and End of Service Life (End).

5.3 Testing the Alarm

Press the 'TEST' button to check the alarm function. The detector will emit a loud 85dB alarm sound and the red LED will flash. This also allows you to check CO peaks or mute the alarm during an event.

5.4 Alarm Response

The detector provides rapid response to varying CO concentrations:

Diagram illustrating rapid response to CO concentration levels
Figure 6: CO concentration levels and detector response.

If the alarm sounds:

  1. Immediately move to fresh air outdoors or open all doors and windows to ventilate the area.
  2. Do a head count to check that all persons are accounted for.
  3. Do not re-enter the premises until the alarm has stopped and the area has been thoroughly ventilated.
  4. Seek medical attention for anyone experiencing symptoms of CO poisoning (headache, nausea, dizziness).
  5. Contact the appropriate authorities (fire department or gas company) to investigate the source of CO.

6. Maintenance

6.1 Battery Replacement

The detector uses 3 AA alkaline batteries with an approximate life of 2 years. When the yellow LED flashes and the display shows 'Lb' (Low Battery), it's time to replace the batteries. Refer to section 4.1 for battery installation instructions.

6.2 Cleaning

Clean the detector regularly to prevent dust and debris from accumulating and affecting its performance. Use a soft, damp cloth to wipe the exterior. Do not use harsh chemicals, abrasive cleaners, or spray directly into the detector.

7. Troubleshooting

Problem Possible Cause Solution
Red LED flashing and alarm sounding High CO concentration detected Follow alarm response procedures (Section 5.4). Ventilate the area and seek professional help.
Yellow LED flashing, display shows 'Lb' Low battery Replace all 3 AA alkaline batteries (Section 6.1).
Yellow LED flashing, display shows 'End' End of service life The detector has reached its 10-year lifespan. Replace the unit immediately.
Yellow LED flashing, no 'Lb' or 'End' Malfunction or fault Press the 'TEST' button. If the fault persists, contact customer support.
No display, no LEDs No power / Dead batteries / Incorrect battery installation Check battery installation and replace batteries if necessary.

8. Specifications

Model STC-X2
Sensor Type Electrochemical CO sensor
Power Supply 3 x AA Alkaline Batteries
Battery Life Approx. 2 years
Sensor Lifespan 10 years
Alarm Volume 85dB at 1 meter
Operating Temperature 0°C to 40°C (32°F to 104°F)
Operating Humidity 30% to 90% RH (non-condensing)
Dimensions (L x W x H) 15 cm x 12 cm x 15 cm (approximate package dimensions)
Weight 0.52 kg (approximate package weight)
Standard EN50291

9. User Tips

  • Always keep spare AA batteries on hand for quick replacement when the low battery indicator appears.
  • Consider placing detectors in multiple locations, especially near sleeping areas and any rooms with fuel-burning appliances.
  • Familiarize yourself and your family with the sound of the CO alarm and what to do in case of an alarm.

10. Warranty and Support

CPVAN products are manufactured to high-quality standards. For any questions, technical assistance, or warranty claims, please refer to the contact information provided by your retailer or visit the official CPVAN website for support resources.

© 2024 CPVAN. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.