BAOFENG BF-K69

Contents

Baofeng BF-K69 Multi-Band Ham Radio User Manual

Model: BF-K69 | Brand: BAOFENG

1. Introduction

Thank you for purchasing the Baofeng BF-K69 Multi-Band Ham Radio. This easy-to-use radio features dual band, dual display, and dual watch capabilities, designed to provide secure, instant, and reliable communications. This manual provides essential information to help you achieve maximum performance from your radio.

For a detailed PDF version of this manual, please refer to the K6 Series Amateur Radio Owner's Manual (PDF).

Key Features:

  • Frequency Range: FM radio 76-108 MHz; AM aviation frequency band: 108-136MHz (RX); VHF1: 136-174MHz (RX&TX); VHF2: 220-260MHz (RX&TX); UHF1: 400-520MHz (RX&TX); UHF2: 350-390MHz (RX).
  • Wireless Copy Frequency: One-touch search frequency for easy pairing and grouping.
  • Memory Channels: Up to 999 memory channels.
  • Display: Large color screen with full keyboard and fully open menu operation.
  • Charging: Support USB (Type-C) direct charging and charging dock.
  • Power: High or low power selectable.
  • Functions: DTMF encoder and manual dial, VOX (voice activated transmit), Stopwatch function, Alarm function, LED flashlight, End of transmission tone (Roger Beep), Battery save function, Busy channel lock out, Ten (10) levels of Squelch adjustment.
  • Additional Features: Dual watch / Dual reception, Programmable repeater offset, Transmission time-out timer, Two (2) pins for Kenwood accessory port.
Baofeng BF-K69 Walkie Talkie with key features highlighted
Figure 1: Baofeng BF-K69 Walkie Talkie highlighting multi-band, one-touch search, 999 memory channels, AM aviation band receiving, high/low power, and Type-C charging.

2. Safety and Regulations

Please read and understand all safety warnings and regulations before operating this device.

EU Regulatory Conformance:

This product complies with Directive 2014/53/EU and other relevant EU regulations (2006/66/EC, 2011/65/EU, (EU)2015/863, 2012/19/EU). It can operate under 2000m.

WARNING! European Users should note that operation of this unit in Transmit mode requires a valid Amateur Radio License from their respective Countries Amateur Radio Licensing Authority for the Frequencies and Transmitter Power levels that this Radio transmits on. Failure to comply may be unlawful and liable for prosecution. Refer to the “EU” specification guide 2014/53/EU.

PMR446, FRS, GMRS, MURS: You may be tempted to use PMR446 (in Europe) or FRS, GMRS, MURS (in the USA) frequencies. Do note however that there are restrictions on these bands that make this transceiver illegal for use.

Compliance with RF Exposure Standards:

The radio complies with RF energy exposure standards and guidelines, including:

  • United States Federal Communications Commission, Code of Federal Regulations; 47 CFR § 1.1307, 1.1310 and 2.1093
  • American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005; Canada RSS102 Issue 5 March 2015

Guidelines and Operating Instructions for RF Exposure:

  • Do not remove the RF Exposure Label from the device.
  • User awareness instructions should accompany the device when transferred to other users.
  • Do not use this device if the operational requirements described herein are not met.
  • Transmit no more than the rated duty factor of 50% of the time.
  • Keep the radio unit at least 2.5cm away from the face.
  • When worn on the body, always place the radio in an approved holder, holster, case, or body harness or by use of the correct clip for this product.
  • Use of non-approved antennas, batteries, and accessories causes the radio to exceed FCC RF exposure guidelines.

Operating Prohibitions:

  • Do not operate in locations containing fuels, chemicals, explosive atmospheres, or other flammable/explosive materials unless using an approved Ex-protection model.
  • Do not operate near any blasting area.
  • Do not operate near medical or electronic equipment vulnerable to RF signals.
  • Do not hold the product while driving.
  • Do not operate in areas where wireless communication equipment is prohibited.
  • Do not disassemble, modify, or repair the product without authorization.

Precautions for Batteries:

Charging Prohibitions:

  • Do not charge or replace your battery in a location containing fuels, chemicals, explosive atmospheres.
  • Do not charge a wet battery; dry it with a soft, clean cloth first.
  • Do not charge a battery suffering deformation, leakage, or overheating.
  • Do not charge with an unauthorized charger.
  • Do not charge in a location with strong radiation.
  • Avoid overcharging to prolong battery life.

Maintenance Instructions:

  • Clean the charging connector regularly.
  • Charge the battery between 5°C~40°C (40°F - 105°F).
  • Turn off the radio when charging an attached battery.
  • Do not remove the battery or unplug the power cord during charging.
  • Do not dispose of the battery in fire.
  • Do not expose to direct sunlight or other heating sources.
  • Do not squeeze, penetrate, or remove the battery housing.

Transportation Instructions:

  • Damaged batteries must not be transported.
  • Separate batteries from metal parts to avoid short circuits during transport.
  • The radio must be switched off and secured against accidental activation if the battery is attached.

3. Package Contents

Verify that all items are present in your package. If any item is missing, please contact your dealer.

  • 1 x Radio
  • 1 x Fast desktop charger
  • 1 x Antenna
  • 1 x Li-Ion battery pack
  • 1 x Wall adaptor
  • 1 x Belt clip
Standard equipment list for Baofeng BF-K69
Figure 2: Standard equipment list including the radio, antenna, battery, charger, belt clip, wrist strap, and manual.

4. Setup

4.1 Charging the Battery Pack

The Li-ion battery pack is not charged at the factory. Please charge it before first use. For optimal performance, fully charge and discharge the battery two or three times. Use only the specified charger provided by Baofeng.

How to Charge:

  1. Plug the AC adaptor into an AC outlet, then connect the cable to the DC jack on the charger. The indicator light will blink orange.
  2. Plug the battery or the radio into the charger. Ensure good contact with charging terminals. The indicator light will turn red.
  3. A full charge takes approximately 2-5 hours. The indicator light turns green when charging is complete.
  4. Remove the battery or radio from the charger.

Note: If the radio is powered on during charging, the indicator may not turn green to show full charge. The radio consumes energy when on, affecting the charger's ability to detect correct battery voltage. It is recommended to power off the radio while charging.

LED Indicator Status:

StatusLED Indication
No BatteryGreen and red alternately flashing
Charge NormallyRed
Fully ChargedGreen
Trouble (e.g., battery too warm, short-circuited)Red blinks fast for a long time

How to Store the Battery:

  • Store the battery at 80% discharged.
  • Keep in a low temperature and dry environment, away from hot places and direct sunlight.
  • Do not short circuit terminals or remove the casing.

Using the Type-C USB Charger:

The Type-C USB port allows convenient charging of your Li-ion battery pack.

  1. Ensure your radio is turned OFF.
  2. Plug the Type-C USB cable into the Type-C USB charging port on your battery. Connect the other end to a wall power outlet.
  3. An empty battery will be fully charged in approximately 4 hours.
  4. The battery meter on the LCD will indicate charging.

Note: For optimal battery life, remove the radio from the charger within 6 hours. Do not store the radio while connected to the charger.

Type-C charging options for Baofeng BF-K69
Figure 3: Type-C charging options, including car charging, power bank, USB plug, and wall charging.

4.2 Installing/Removing the Antenna

To install, screw the antenna clockwise onto the connector on top of the radio until secure. To remove, unscrew counter-clockwise.

4.3 Installing the Belt Clip

Align the grooves of the belt clip with those on the radio and push down until it clicks into place. To remove, use a flat-bladed object to press the belt clip tab away from the radio, then slide it upward.

4.4 Installing the Battery Pack

Before attaching or removing the battery, ensure the radio is turned off. Align the battery with the radio body, then slide it upward along the guide-rails until it clicks into place. To remove, press the battery release above the battery pack and slide it downward.

4.5 Installing Additional Speaker/Microphone (Optional)

Pry open the rubber MIC-Headset jack cover and insert the Speaker/Microphone plug into the double jack.

5. Radio Overview

5.1 Buttons and Controls of the Radio

Diagram of Baofeng BF-K69 buttons and controls
Figure 4: Labeled diagram of the BF-K69 radio's buttons and controls.
  1. Antenna
  2. LED flashlight
  3. Status LED
  4. Power / Volume knob
  5. Battery release latch
  6. PTT - Push to talk
  7. SK1-Programmable key (flashlight/alarm switch)
  8. SK2-Programmable Key (Radio/Monitor)
  9. Accessory jack
  10. Type-C charging indicator
  11. V/M-VFO/MR mode key
  12. A / B select key
  13. SWEEP key
  14. MENU Key
  15. Type-C charging port
  16. Color LCD
  17. Speaker
  18. Microphone
  19. EXIT Key
  20. Keypad

5.2 LCD Display

The LCD displays various icons indicating the radio's status and settings.

IconDescriptionIconDescription
MxxxMemory channelDWDual watch enabled
VFOFrequency ModeTXTransmitting
VOXVOX enabledRXReceiving
CTCCTCSS enabledRReverse function enabled
DCSDCS enabled►Indicates active band or channel
NNarrowband enabled+/-Frequency shift direction if enabled in VFO
H/LTransmit power level indicator (High/Low)Battery level indicator
Squelch Open/Close Indicator

5.3 Status Indications

The status LED indicates the radio's activity:

LED IndicatorRadio Status
Constant RedTransmitting
Constant GreenReceiving
OffStandby

5.4 Main Keypad Controls

  • V/M: Short press to switch frequency or channel mode. Press and hold to toggle channel display mode (CH/FREQ/NAME).
  • A/B: Short press to toggle upper screen (A)/lower screen (B). Press and hold to switch Double Wait/Signal Wait/Dual Watch off modes.
  • One-Touch Search Key: Short press to enter One-Touch search key.
  • EXIT: Short press to return to menu or previous menu. Press and hold to enter frequency sweep mode.
  • *: Long press to lock or unlock the keypad.
  • #: Short press to enter DTMF dial. Press and hold to scan on and scan off.
  • 0 [space]: Press and hold to enter weather switch to select weather channel.

6. Basic Operations

6.1 Power On/Off and Volume Adjustment

To turn the radio on, rotate the Volume/Power knob clockwise until you hear a "click". The display will show a frequency or channel. To turn off, rotate the knob counter-clockwise until you hear a "click".

Adjust the volume by rotating the Volume/Power knob. Use the monitor function (enabled via the [FM broadcast/Monitor] key below the PTT) to adjust volume to un-squelched static.

6.2 Main Band/Sub Band Select

In standby mode, press the [A/B] key to switch between the upper (A) and lower (B) displays. The selected display becomes the active listening and transmit frequency/channel. Press and hold [A/B] to quickly switch Double Wait/Signal Wait.

6.3 VFO/Channel Switch

Press the [V/M] key to switch between VFO (Frequency) and Channel (MR) mode. In MR mode, the channel number is displayed. In VFO mode, 'VFO' is displayed. In MR mode, press and hold [V/M] to switch between frequency, channel, and name display modes.

6.4 Frequency (VFO) Mode

In VFO mode, navigate frequencies using the ▲/▼ keys or by direct input on the numeric keypad. For example, to enter 436.61250 MHz on display A:

  1. In standby, press [V/M] to switch to VFO mode.
  2. Enter [4][3][6][6][1][2][5][0] on the numeric keypad.

WARNING! Transmitting on unauthorized frequencies is illegal. The scanning and receive function of the aviation frequency band (AM108-136MHz) and the police frequency band (350-390MHz) is limited to VFO mode and manual input.

6.5 Channel (MR) Mode and Channel Selection

Channel (MR) mode is practical for everyday use with preprogrammed channels. Navigate channels using the ▲/▼ keys or by inputting channel numbers on the keypad (e.g., [0][1][2] for channel 12).

6.6 Making a Call

Note: Press [A/B] to switch the main channel if two channels are displayed. In standby, press [V/M] to switch between VFO and MR mode.

  • Channel Mode Call: Select a channel, then hold down the [PTT] key to transmit. Speak into the microphone with normal tone. The red LED will be on.
  • Frequency Mode Call: Switch to frequency mode, input the working frequency, then hold down the [PTT] key to transmit. The red LED will be on.
  • Receive a Call: Release the [PTT] key. The green LED will be on when receiving a call.

Note: For best reception, keep the microphone 2.5 cm to 5 cm from your mouth during transmission.

6.7 Using the Flashlight

Press the [SK1] key to turn on the high-intensity LED flashlight. Press [SK1] again for strobe emergency mode, and a third time to turn it off.

6.8 Emergency Alert

To activate, press and hold the [SK1] key for 3 seconds. The radio will emit a loud siren and the flashlight will flash. Press [SK1] to exit. WARNING: Only use in actual emergencies.

6.9 FM Radio (FM)

The radio can receive FM radio in the 65-108MHz range.

  1. In frequency or channel mode, press [SK2] to turn on the radio.
  2. Select the desired frequency with the ▲/▼ keys or input directly. Alternatively, press #z to automatically search for a station.
  3. Press [SK2] to exit FM radio.

Note: While listening to FM, the radio automatically switches to the receiving signal's frequency/channel for normal transmitting/receiving. If the signal disappears, it returns to FM mode.

6.10 Monitor

In standby, press and hold the [SK2] key to enter Monitor mode, allowing you to hear weak signals or signals with matched carrier but no signaling. Release [SK2] to exit. If no signal is present, it will emit noise.

6.11 Keypad Lock

The keypad lock disables all keys except the three side keys. To enable/disable, press and hold the * key for two seconds. The radio can also be set to automatically lock after ten seconds via the menu.

6.12 Frequency Reversal

A short press of the * key momentarily enables the reverse function, reversing your transmit and receive frequencies. An 'R' will appear on the LCD next to the +/- indicator.

6.13 TX Repeaters Tone

Press [PTT] + [SK2] to send a 1750Hz repeaters tone. This is useful for communications through repeaters. This function works even with the keypad locked.

  1. Hold the SWEEP key; the screen will display “SEARCH SWEEK...”.
  2. If an effective frequency is received, it will be displayed along with CTCSS/DCS if present (or NONE).
  3. Press the [MENU] key to save the searched frequency and CTCSS/DCS to a channel.

Note: During search, press #z to switch between UHF or VHF bands.

6.15 Weather Radio/Scan Weather Channel (NOAA)

The radio has a NOAA Weather Radio function for receiving weather reports and scanning NOAA channels.

  1. To turn on NOAA Weather Scan, press the [OSQL] key for 3 seconds; a cloud icon will appear, and the radio will enter Weather band mode.
  2. Press and hold the #z key for 3 seconds to start automatic scanning of all 10 channels. It will stop on active channels. Press and hold #z again to stop the scan.
  3. After stopping the scan, manually select the weather channel by pressing the ▲/▼ key.
  4. To exit Weather Radio broadcast mode, press the [EXIT] or [PTT] key.

Weather Channel Frequencies:

Channel NumberRX Frequency MHzChannel NumberRX Frequency MHz
Wx-01162.550Wx-06162.500
Wx-02162.400Wx-07162.525
Wx-03162.475Wx-08161.650
Wx-04162.425Wx-09161.775
Wx-05162.450Wx-10163.275

Note: Weather Channels Wx 1 Thru 10 are Receive-only channels for NOAA and Canadian weather broadcasts. You cannot transmit on these channels.

NOAA Weather Radio and FM Radio features
Figure 5: Display showing NOAA Weather Radio and FM Radio capabilities.

7. Advanced Features

7.1 Working the Menu System

Basic Use:

  1. Press [MENU] to enter the menu.
  2. Use the ▲/▼ keys to navigate.
  3. Press [MENU] again to select an item.
  4. Use ▲/▼ keys to select a parameter.
  5. To confirm, press [MENU]. To cancel, press [EXIT].
  6. Press [EXIT] to exit the menu at any time.

Using Shortcuts:

Each menu item has a numerical value for direct access.

  1. Press [MENU].
  2. Enter the menu item number on the keypad.
  3. Press [MENU] to enter the item.
  4. Use ▲/▼ keys or numerical keypad for parameters.
  5. To confirm, press [MENU].

Programmed Keys:

The [SK1] and [SK2] keys can be programmed for various functions via Menu 48/49/50 (PF1 Press/PF1 LongPre/PF2 Press).

FunctionDescription
NoneNo function
Torch On/OffQuick switch torch
Power SelectQuickly switch between high, low transmit power
Scan On/OffQuickly switch scanning function on or off
VOX On/OffQuickly switch on/off VOX function
Alarm on/offQuickly establishes an emergency call
Radio on/offQuickly switch on or off the FM radio function

7.2 Scanning

The radio features a built-in scanner for VHF and UHF bands. In VFO mode, it scans in steps according to your set frequency step. In Channel (MR) mode, it scans your channels. Dual Watch is inhibited while scanning.

To enable the scanner, press and hold the #z key for about two seconds. Press and hold #z again to exit scanning mode.

Scanning Modes:

Configurable via Menu 19.

  • Time Operation (TO): Scanner stops on a signal, resumes after a preset time.
  • Carrier Operation (CO): Scanner stops on a signal, resumes after a preset time with no signal.
  • Search Operation (SE): Scanner stops on a signal. Must manually resume by holding #z.

Frequency Scanning:

In frequency mode, press #z for more than 2 seconds to start scanning. Change direction with ▲/▼ keys. Press #z to stop.

Channel Scanning:

In channel mode, press #z for more than 2 seconds to start scanning. Change direction with ▲/▼ keys. Press #z to stop.

Scan CTCSS/DCS:

In standby mode, press [MENU] [1][6] for Scan CTCSS or [MENU] [1][7] for Scan DCS. Press [MENU] to start scanning. This function requires the receiving band to detect a signal and cannot be activated in Channel mode.

7.3 Manual Programming (Channels Memory)

The radio features 999 memory channels. Each channel can store receive/transmit frequencies, power, signaling, bandwidth, ANI/PTT-ID, and a six-character alphanumeric identifier.

Programming a Channel Repeater Offset with CTCSS Tone:

Example for Channel 10 (RX = 432.55000 MHz, TX = 437.55000 MHz (+5 Offset), TX CTCSS tone 123.0):

  1. Press [EXIT] to switch menus.
  2. Press [V/M] to set radio to VFO mode.
  3. [MENU] [1][4] [MENU] [1][0] [MENU] [EXIT] (Deletes prior data in channel 10).
  4. [MENU] [0][5] [MENU] 123.0 [MENU] [EXIT] (Selects desired TX encode tone).
  5. Enter RX frequency (e.g., 43255000).
  6. [MENU] [1][3] [MENU] [1][0] [MENU] [EXIT] (Enters desired channel 10, RX added).
  7. Enter TX frequency (e.g., 43755000).
  8. [MENU] [1][3] [MENU] [1][0] [MENU] [EXIT] (Enters same channel 10, TX added).
  9. Press [V/M] to return to MR mode.

Programming a Simplex Channel with CTCSS Tone:

Example for Channel 10 (RX = 432.6625 MHz, TX CTCSS tone 123.0):

  1. Press [EXIT] to switch menus.
  2. Press [V/M] to set radio to VFO mode.
  3. [MENU] [1][4] [MENU] [1][0] [MENU] [EXIT] (Deletes prior data in channel 10).
  4. [MENU] [0][5] [MENU] 123.0 [MENU] [EXIT] (Selects desired TX encode tone).
  5. Enter RX frequency (e.g., 43266250).
  6. [MENU] [1][3] [MENU] [1][0] [MENU] [EXIT] (Enters desired channel 10, channel added).
  7. Press [V/M] to return to MR mode.

7.4 Repeaters Programming

To program repeaters, ensure you know the transmit and receive frequencies and are authorized to use them.

  1. Press [V/M] to set the radio to VFO mode.
  2. Enter the repeater's output (your receiving) frequency on the numeric keypad.
  3. Press [MENU].
  4. Enter [1][2] for frequency offset. Press [MENU].
  5. Enter the specified frequency offset. Press [MENU] to confirm.
  6. Enter [1][1] for offset direction. Use ▲/▼ keys to select + (positive) or - (negative). Press [MENU] to confirm.
  7. (Optional) Save to memory or set CTCSS.
  8. Press [EXIT] to exit.

Note: If connection issues occur, recheck settings. Some repeaters use a 1750Hz tone burst to open. Refer to the "1750Hz Tone-burst" section for details. Contact your radio system administrator or local amateur radio club for further assistance.

7.5 VOX (Voice Activated Transmit)

VOX allows hands-free communication. Speak into the microphone to activate transmission.

  1. In standby, press [MENU] + 25. Screen displays “VOX Switch”. Press [MENU].
  2. Use ▲/▼ keys to turn VOX ON/OFF.
  3. In standby, press [MENU] + 26. Screen displays “VOX Level”. Press [MENU].
  4. Use ▲/▼ keys to select VOX level (1-9, 1 being least sensitive). Press [MENU] to confirm.
  5. Press [EXIT] to return to standby.

Note: VOX is not enabled in Scan or FM Radio mode.

7.6 Dual Watch

Dual Watch allows monitoring two channels simultaneously. The radio features single-receiver Dual Watch functionality.

Enabling or Disabling Dual Watch Mode:

  1. Press [MENU].
  2. Enter 38 for Dual Watch. Press [MENU].
  3. Use ▲/▼ keys to select Double Wait/Signal Wait/OFF. Press [MENU] to confirm.
  4. Press [EXIT] to exit.

7.7 Stopwatch Timer

In standby mode, press [MENU] + 57. The screen displays “STOP WATCH”. Press [MENU] to start/restart counting. Stop counting before pressing [EXIT] to exit.

7.8 DTMF (Dual-Tone Multi-Frequency)

DTMF is an in-band signaling method used for automation systems and remote control, common in amateur radio repeaters.

DTMF Frequencies and Corresponding Codes:

1209Hz1336Hz1477Hz1633Hz
697Hz123A
770Hz456B
852Hz789C
941Hz*0#D

To send DTMF codes, press the corresponding key(s) while holding down the PTT key. This works even with keypad lock enabled.

7.9 Customization

The radio allows customization of visual and audible features.

Display Backlight (ABR) - Menu 51:

In standby mode, press [MENU] + 51. Screen displays “ABR”. Press [MENU]. Use ▲/▼ keys to select ON/delay time (5/10/15/20/30/60 seconds). Press [MENU] to confirm. Press [EXIT] to return.

Beep Prompt (BEEP) - Menu 32:

Enables/disables key press beep tone. In standby, press [MENU] + 32. Screen displays “BEEP PROMPT”. Press [MENU]. Use ▲/▼ keys to turn ON/OFF. Press [MENU] to confirm. Press [EXIT] to return.

Voice Function (VOICE) - Menu 30:

Enables/disables audible voice confirmation of key presses. In standby, press [MENU] + 30. Screen displays “VOICE”. Press [MENU]. Use ▲/▼ keys to select OFF/ON. Press [MENU] to confirm. Press [EXIT] to return.

Language of the MENU (LANGUAGE) - Menu 29:

Sets the menu language (English). In standby, press [MENU] + 29. Screen displays “LANGUAGE”.

Working Mode (MDF-A) - Menu 39:

Sets the display mode: Frequency (FREQ), Channel (CH), or Channel Name (NAME). In standby, press [MENU] + 39. Select desired mode with ▲/▼ keys. Press [MENU] to confirm.

Roger Beep (ROGER) - Menu 33:

Enables/disables the end-of-transmission tone. In standby, press [MENU] + 33. Screen displays “ROGER”. Press [MENU]. Use ▲/▼ keys to select OFF/ON. Press [MENU] to confirm. Press [EXIT] to return.

Power On Message (POWER ON MSG) - Menu 40:

Customizes the welcome message on display when radio powers on. Options: VOLTAGE, MESSAGE, LOGO. In standby, press [MENU] + 40. Screen displays “POWER ON MSG”. Press [MENU]. Use ▲/▼ keys to select option. Press [MENU] to confirm. Press [EXIT] to return.

Power On Password (Power On PWD) - Menu 37:

Enables/disables a password prompt when the radio powers on. Default password is 000000. In standby, press [MENU] + 37. Screen displays “POWER ON PWD”. Press [MENU]. Use ▲/▼ keys to select ON/OFF. Press [MENU] to confirm. Press [EXIT] to return.

Reset - Menu 56:

Two reset modes: VFO (resets frequency settings only) and ALL (resets all settings). In standby, press [MENU] + 56. Screen displays “RESET”. Press [MENU]. Use ▲/▼ keys to select VFO or ALL. Press [MENU] to confirm. Screen displays “Sure to reset?”. Press [MENU] again to confirm. The radio will turn off and reboot.

8. Technical Specifications

FeatureSpecification
Frequency bandFM65-108MHz; AM108-136MHz(Rx); 350-390MHz(Rx); 136-174MHz (Rx/Tx); 220-260MHz (Rx/Tx); 400-520MHz (Rx/Tx)
Memory channels999
Power supplyLi-Ion battery 7.4V/1400 mAh (BL-K6)
Operating temperature-10°C to + 45°C
Working modemonoband/dualband
ModulationF3E(FM)
Max. frequency deviation≤ ±5KHz
Spurious radiation< -60dB
Frequency stability±2.5 ppm
Rx sensitivity< 0.2uV
Audio output power≥ 500mW
Dimensions (LxAxP)64x121x35mm
Weight240g

Specifications are subject to change without notice.

WARNING: Direct plug-in AC/DC power supply must be used for disconnecting the transceiver from the mains; the desktop charger must be positioned close to the unit and easily accessible.

9. Troubleshooting Guide

If you encounter issues with your radio, refer to the table below for common problems and solutions.

PhenomenaAnalysisSolution
Cannot turn on the radio.Battery improperly installed, power run out, or poor/damaged contacts.Reattach/replace battery. Clean/replace contacts.
Voice weak or intermittent during receiving.Battery voltage low, volume level low, loose/incorrect antenna, blocked speaker.Recharge battery, increase volume, reattach antenna, clean speaker.
Cannot communicate with other group members.Frequency/signaling type inconsistent, too far away.Verify TX/RX frequency and signaling type. Move closer.
Hear unknown voices or noise.Interrupted by radios on same frequency, radio in analog mode with no signaling.Change frequency, adjust squelch level. Request dealer to set signaling.
Unable to hear due to too much noise/hiss.Too far from others, unfavorable position (e.g., blocked by buildings), external disturbance.Move closer, move to open area, restart radio. Stay away from interference.
Radio keeps transmitting.VOX turned on, headset not in place.Turn off VOX. Check headset.

Note: If these solutions do not resolve your issues, please contact your dealer for technical support.

10. User Tips

  • Battery Management: Always ensure your battery is adequately charged before use. For optimal battery longevity, avoid overcharging and store the battery at approximately 80% charge when not in use for extended periods.
  • Frequency Usage: Be mindful of local regulations regarding frequency usage. Transmitting on unauthorized frequencies is illegal and can lead to penalties. Always verify your licensing requirements for transmit mode.
  • Squelch Adjustment: If you are experiencing excessive background noise, try adjusting the squelch level (Menu 23) to filter out weaker signals and static.
  • VOX Function: For hands-free operation, enable the VOX function. Experiment with different VOX sensitivity levels (Menu 26) to find the setting that best suits your environment and voice.
  • Wireless Copy Frequency: Utilize the one-touch search frequency feature (Menu 5.15) for quick and easy pairing with other radios, simplifying group communication setup.

11. Warranty and Support

For any technical support, warranty claims, or further queries not covered in this manual, please contact your authorized Baofeng dealer or the point of purchase. They will be able to provide specific assistance related to your product.

© 2024 BAOFENG. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.